STI STI-34098 User manual

· Works in conjunction with a control panel
· Operates up to 1,000’ (line of sight)
· Form “C” relay, 30V AC/DC, 1A
· Form “C” contact enables the transmitter to interconnect
with another system
· 12VDC operation
· Latching or auto restore mode
Single Channel
Slave Receiver
STI-34098
We protect the things that protect you.®
Install 34098, MAY2020
Important Notice
This product has been tested and complies with the specications for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resident
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which is found by turning equipment on and o, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and devices.
- Connect the equipment to an outlet other than the receiver’s.
- Consult a dealer or an experienced radio/TV technician for assistance.
Operation is subject to the following two conditions: (1) this device may cause interference, and (2) this device must
accept interference, including interference that may cause undesired operation of the device. Changes or modications
not expressly approved by Safety Technology International, Inc. could void your authority to operate this equipment.
To reduce potential radio interference to other users, the antenna type and its gain should be chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.
This product meets the applicable industry Canada Technical Specications.
Le présent matériel est conforme aux spécications techniques applicables d’Industrie Canada.
When installed without the STI-34099 case, STI highly recommends that the receiver is installed inside a panel enclosure
where it will not be subjected to direct electro static discharge (ESD) and that appropriate handling is used to minimize
ESD during installation process.
This device is a wireless receiver intended for home and oce use in all EU and EFTA member states.
Technical Support
Contact STI at 248-673-9898
Additional Wireless Alert Series Products
STI-34098 Single Channel Slave Receiver
STI-34099 Single Channel Slave Receiver Case
STI-V34104 4-Channel Voice Receiver
STI-34108 8-Channel Receiver
STI-34188 8-Zone Relay Board
STI-34101 Solar Powered Driveway Monitor Sensor
STI-34151 Battery Powered Driveway Monitor
Sensor
STI-34201 Wireless Mail Alert Sensor
STI-34301 Wireless Garage Sentry Sensor
STI-34401 Wireless Universal Alert Sensor
STI-34501 Wireless Door Entry Alert®Sensor
STI-34601 Wireless Doorbell Button
STI-34752 Indoor/Outdoor Wireless PIR
STI-6200WIR Wireless Fire Extinguisher Theft Stopper
STI-6200WIR4 Wireless Fire Extinguisher Theft Stopper w/
Receiver
STI-6400WIR Wireless Exit Stopper Door Alarm
STI-6400WIR4 Wireless Exit Stopper Door Alarm with Receiver
STI-6517A Stopper Station Shield with Sound
STI-6517B Stopper Station Shield with Sound and Transmitter
STI-6517C Stopper Station Shield with Wireless Transmitter
STI-6517D Wireless Stopper Station Shield with Button
Sound and Transmitter
STI-30105 Extended Antenna
STI-34105 Voltamax 12VDC (500mA) Power Supply
STI-34106 Keyfob
STI-34188 8-Zone Relay Board
Taylor House • 34 Sherwood Road • Bromsgrove, Worcestershire • B60 3DR • England
Tel: [phone] • [email protected] • www.sti-emea.com
Unit 7A • Lockhead Avenue • Airport Business Park • Waterford • X91 HWF2 • Ireland
[email protected] • www.sti-emea.com
2306 Airport Rd • Waterford, MI 48327, USA
Phone: [phone] • [email protected] • www.sti-usa.com
USA EMEA

-2-
Contact Rating (Resistive) Specications
- 30V AC/DC, 1A - Standby Power: 12VDC, 10mA
- Max Operating: 12VDC, 16mA
MODE
SWITCH POSITIONS
Program
Latching
Auto Restore
Antenna
Sounder
Yellow Reset
Leads
+
_
NC
COM
NO
PROGRAM SOUNDER LED RELAY
Power ON in program Start-Up tone will sound Alernating RED and GREEN Normal
Activate transmitter Will double beep Alternating RED and GREEN Normal
LATCHING SOUNDER LED RELAY
Power ON in latching (normal) Start-up tone will sound Flash GREEN every 2-3 seconds Normal
Activate transmitter Will double beep Solid RED Switched
Transmitters restores No sound Flashing RED Switched
AUTO RESTORE SOUNDER LED RELAY
Power ON in auto restore (normal) Start-Up tone will sound Flash GREEN every 2-3 seconds Normal
Activate transmitter Will double beep Solid RED Switched
Transmitter restores No sound Flash GREEN every 2-3 seconds Normal
Modes of Operation
{
12VDC
-3-
Instructions
Move switch to program. LED will ash RED and GREEN. Program transmitter into receiver by activating
transmitter (see transmitter instructions). Speaker will double beep to conrm programming. Move mode
switch to intended mode. Activate transmitter to conrm enrollment.
To operate in Latching - Move switch to center position. The LED will turn GREEN and ash every 2-3
seconds.
When activated in Latching - Sounder will double beep and LED will turn to solid RED state. When
restore signal is received from transmitter LED will ash RED.
Options for restoring the receiver (LED ashing RED)
• Move slide switch to Auto Restore (bottom position) and then back to Latching.
• Use Keyfob (STI-34106) - press the OFF button and then press the ON button.
• Hard-wire the momentary switch to yellow reset leads on receiver and cycle switch.
To operate in Auto Restore – Move switch to bottom position. The LED will ash GREEN every 2-3
seconds. When activated in Auto Restore, LED will go solid RED until the restore transmission is received.
Once received, the LED will ash GREEN.
Keyfob Operation with STI-34098 Receiver
Keyfob has 2 functions:
• ON/OFF – can be used to reset latched receiver to normal after the restore signal is sent.
• RED and WHITE buttons can be used as alert transmitter.
· RED button sends alert signal.
· WHITE button sends restore signal.
Programming Keyfob in Receiver
Move switch to Program Mode. LED ashes alternating RED/GREEN.
Program ON/OFF reset function – press ON and OFF buttons at the same time to enroll.
Receiver will beep twice to acknowledge enrollment.
Enrolling the keyfob will delete any previously enrolled keyfob.
Program RED/WHITE buttons – while in Program Mode, press the RED and WHITE buttons
simultaneously. The receiver will beep twice to acknowledge enrollment. The RED and WHITE buttons
function as a transmitter. Programming these buttons will delete previously programmed transmitters.
Supervisory signal (3 Types) - Flashing Amber LED (RED and GREEN ashing together) and the sounder
will beep once every minute. Signal will show up within 18-24 hours.
1. Tamper on transmitter is open.
2. Low battery signal from transmitter.
3. Transmitter is out of range.
Notes
• STI-34098 receives signal from only one transmitter.
• Attempting to program a second transmitter will delete original transmitter.
• If receiving a signal from another 433.92 MHz transmitter, the LED will ash GREEN for 3-5seconds.
• Professional installation only.
Warranty Information
Safety Technology International, Inc. warrants to the original consumer/purchaser that this product shall
be free of defects in material and workmanship under normal use and circumstances for a period of one
(1) year from the original date of purchase.
Electronic warranty form at www.sti-usa.com/wc14.