Stiegelmeyer Libra User manual

Last updated: 09-12-2021 294236_V1
Instruction Manual
Care Bed
Libra

Instruction Manual for Libra Care Bed
Page 2
Libra care bed
Similar to illustration!
In this instruction manual, numbers and letters that appear in round brackets ()
and bold type refer to the care bed’s operating devices as shown in this and the
following images.
Item
Description
1
Footboard
2
Full-length safety side bars (standard)
3
Removable centre support (optional)
4
Handset
5
Headboard
6
Combined safety side with bars (optional)
7
Mattress retainer bar
8
Side panel
9
Holder for centre support (optional)
10
Individual axle braking (standard)
Central locking (optional) –only operated at foot end
1
2
3
4
5
5
6
8
10
10
9
7

Instruction Manual for Libra Care Bed
Page 3
Libra –floor access Plus variant
This version has no metal support bars along the sides of the chassis.
Libra beds can also be supplied without safety sides. Refer to chapter
4.5.6 for more information about this
Features:
Patient lifts and cleaning equipment can easily slide under the bed
thanks to the ground clearance of the chassis
D
“Vario Safe system” split safety side (telescopic, on both sides)
C
“Easy-floor-access” double castors (head and foot end)
(individual axle braking)
D
C
D
D
D
D

Instruction Manual for Libra Care Bed
Page 4
Libra –movo variant
Item
Description
11
Central locking - only operated at foot end
12
100 mm double castors
1
1
12
11

Instruction Manual for Libra Care Bed
Page 5
Contents
1 FOREWORD........................................................................................................................7
2 GENERAL INFORMATION.................................................................................................8
2.1 Definition of the groups of persons involved...................................................9
2.2 Safety information.........................................................................................10
2.2.1 Explanation of the safety symbols used...............................................10
2.2.2 Safety information for the operator.......................................................11
2.2.3 Safety information for the user.............................................................12
2.3 Product description.......................................................................................14
2.3.1 Intended use ........................................................................................14
2.3.2 Use for the intended purpose...............................................................14
2.3.3 Side effects ..........................................................................................15
2.3.4 Particular features of the bed...............................................................15
2.3.5 Special electrical equipment (optional).................................................16
2.3.6 Special mechanical equipment (optional).............................................16
2.3.7 Materials used......................................................................................17
3 PUTTING INTO SERVICE.................................................................................................18
3.1 Checklist: Inspection by the user..................................................................19
3.2 Location requirements..................................................................................20
4 OPERATION......................................................................................................................22
4.1 Moving and braking the bed .........................................................................22
4.1.1 Individual axle braking (standard) ........................................................23
4.1.2 Central locking (optional)......................................................................23
4.1.3 Moving with steering lock (optional with central locking)......................23
4.2 Mechanical adjustment options ....................................................................24
4.2.1 Lower leg rest (LR)...............................................................................24
4.2.2 Manual CPR release of the backrest....................................................25
4.3 Electrical adjustment options........................................................................27
4.3.1 Special safety information on the electrical drive system.....................27
4.3.2 Handset (standard)...............................................................................29
4.3.3 Trendelenburg handset (optional) ........................................................32
4.3.4 Handset locking functions ....................................................................33
4.4 Attachments and special equipment.............................................................34
4.4.1 LED reading light * ...............................................................................34
4.4.2 Under bed light * ..................................................................................35
4.4.3 Patient lifting pole * ..............................................................................36
4.4.4 Grab handle* (triangular grab handle)..................................................37
4.4.5 Bed extension (adaptable) *.................................................................38
4.4.6 Handset holder (optional).....................................................................40
4.4.7 Linen holder *.......................................................................................40
4.4.8 Removing/assembling the headboard/footboard..................................41
4.4.9 Fit/remove the side panels...................................................................46
4.5 Safety sides..................................................................................................51
4.5.1 Full-length safety sides (standard) .......................................................52
4.5.2 Special safety information for safety sides...........................................53
4.5.3 Combined safety sides *.......................................................................55
4.5.4 Removal/installation of the safety side (2) and (6) ...............................61
4.5.5 Split safety sides *................................................................................64

Instruction Manual for Libra Care Bed
Page 6
4.5.6 Variant - without safety sides * ............................................................ 76
4.5.7 Comfort mattress base - 90 cm width (optional) .................................. 77
4.5.8 Comfort mattress base - 100 cm width (optional) ................................ 78
4.6 Inserting the mattress................................................................................... 79
5 CLEANING AND DISINFECTION .................................................................................... 80
5.1 General information on cleaning and disinfection......................................... 80
5.2 Cleaning and disinfection plan ..................................................................... 81
5.3 Instructing users and staff............................................................................ 82
5.4 Cleaning of firmly upholstered components ................................................. 83
5.4.1 Cleaning the fabric upholstery ............................................................. 83
5.4.2 Cleaning faux leather upholstery ......................................................... 83
5.5 Cleaning agents and disinfectants ............................................................... 85
5.6 Handling cleaning and disinfection agents................................................... 87
6 MAINTENANCE................................................................................................................ 88
6.1 By the user................................................................................................... 89
6.2 Responsibilities of the operator.................................................................... 90
6.3 Replacement parts....................................................................................... 96
6.4 Service address ........................................................................................... 96
6.5 Replacement of electrical components ........................................................ 97
6.5.1 Plug assignment on the control unit..................................................... 97
6.5.2 Replacing the handset......................................................................... 99
6.5.3 Connecting a reading lamp at a later date (optional)......................... 100
6.5.4 Connect a battery at a later date (optional equipment)...................... 101
6.5.5 Replace the control unit..................................................................... 104
6.5.6 Initialise the control unit..................................................................... 104
6.5.7 RESET the control unit...................................................................... 106
6.5.8 Replace the motors............................................................................ 106
6.5.9 Decommissioning .............................................................................. 107
7 TROUBLESHOOTING.................................................................................................... 108
8 ACCESSORIES.............................................................................................................. 110
9 TECHNICAL DATA......................................................................................................... 111
9.1 Dimensions and weights ............................................................................ 111
9.2 Electrical data............................................................................................. 111
9.3 Ambient conditions..................................................................................... 114
9.4 Type plate –electrical data ........................................................................ 115
9.5 Other labelling on the product.................................................................... 116
9.6 Information on electromagnetic compatibility (EMC).................................. 117
9.7 Classification.............................................................................................. 120
10 DISPOSAL INSTRUCTIONS.......................................................................................... 121
11 DECLARATION OF CONFORMITY............................................................................... 122

Instruction Manual for Libra Care Bed
Page 7
1 Foreword
Dear Customer,
Stiegelmeyer has built this bed to give you the best possible help with the challenges
posed by nursing and caregiving. We passionately pursue the goal of developing
products that are durable and of a high-quality. Our beds should make patients and
residents feel as safe and comfortable as possible during their stay in bed and also
lighten the workload of nursing and care staff. For this reason, the electrical safety
and all functions are tested prior to delivery. Each bed leaves our factory in perfect
condition.
Correct operation and care are necessary to keep the bed in excellent condition
during long-term use. Please therefore read and observe these instructions carefully.
They will help you to put the bed into service for the first time and to use it on a daily
basis. This instruction manual contains all the information you will need to make it as
easy and safe as possible to control and handle this bed, both for you as the operator
and for your users. It is a practical reference book and should be kept close to hand
at all times.
Even after you have purchased a bed, Stiegelmeyer is still on hand to help at any
time. Our Service business division can provide you with customised solutions in all
matters relating to inspection and maintenance, repair and process optimisation. You
can contact our service centre in Germany by phone on [phone].
Customers outside Germany can contact our distribution companies in their particular
country if they have any questions. Contact details can be found on our website
www.stiegelmeyer.com.
We wish you and your users every success and satisfaction with the care of your
patients and residents.
Stiegelmeyer GmbH & Co. KG
Disclaimer
This product is not licenced for use on the North American market. This applies
particularly to the United States of America. The distribution and use of the care bed
in these markets, including through third parties, is prohibited by the manufacturer.

Instruction Manual for Libra Care Bed
Page 8
2 General information
The Libra care bed is simply referred to as the 'bed' or 'care bed' in this
instruction manual. In addition to the standard functions of the bed, this
instruction manual also describes optional functions and special bed
equipment which might not apply for the model that you have selected.
•This care bed fulfils all the requirements of the Medical Device Regulation (EU)
2017/745 (MDR). It is classified as a Class I active medical device in accordance
with § 13 of the German Medical Devices Act (Medizinproduktegesetz: MPG).
•Please observe your obligations as the operator in accordance with the Medical
Devices Operator Ordinance (Medizinprodukte-Betreiberverordnung, German
abbreviation: MPBetreibV), to ensure that this medical product is always operated
safely and with no risk to residents, users or third parties.
•This instruction manual contains safety information which must be followed. All
users working on and with the care bed must be familiar with the contents of this
instruction manual and follow the safety advice provided.
Instructions for the operator:
Any item of technical equipment, electrical or otherwise, can prove hazardous if not
used properly.
•You are obligated to instruct users in the proper use of this care bed in
accordance with § 5 of the German Medical Devices Operator Ordinance
(MPBetreibV § 5).
•Ensure that users know where this instruction manual is kept, in accordance with
§ 9 of the German Medical Devices Operator Ordinance (MPBetreibV § 9).
Before putting the bed into service for the first time:
•Remove all transport securing devices and packaging film.
•Clean and disinfect the bed before using it for the first time.

Instruction Manual for Libra Care Bed
Page 9
Features of the bed
The main features of the Libra bed are listed below:
Model
Mattress
base height
adjustment
range
Safe
working
load
Type of castor
Castor locking
mechanism
Libra –
standard
Approx. 25
–80 cm
225 kg
50 mm double
castor, hidden in
column
Locked in pairs at
the head/foot end
Optional: central
locking at foot end
Libra –floor
access Plus
variant
Approx. 25
–80 cm
225 kg
8 x 50 mm double
castor, hidden in
column
Locked in pairs at
the head/foot end
Libra –
movo
variant
Approx. 28
–83 cm
225 kg
100mm double
castor
Central locking at
foot end
2.1 DEFINITION OF THE GROUPS OF PERSONS INVOLVED
In this instruction manual, the following groups of persons are defined as:
Operator
The operator (e.g. nursing homes operators) are all natural and legal persons with
property rights to the Libra care bed. The operator is responsible for the safe
operation of this medical device.
Users
Users (nursing staff, carers, attendants etc.) are persons who, based on their
training, experience or briefing, are qualified to operate the bed on their own authority
or to carry out work on it, or have been instructed on how to handle this bed.
Furthermore, they are able to recognise and avoid potential hazards and assess the
clinical condition of the resident.
Residents
In this instruction manual, a resident is defined as a person who is infirm or in need of
care and occupies this bed.
It is a requirement that the operator or user instructs each new resident in the bed
functions that are important for him/her.

Instruction Manual for Libra Care Bed
Page 10
2.2 SAFETY INFORMATION
At the time of leaving the factory, this bed represents state-of-the-art technology.
•Only use the bed if it is in perfect working order.
The most important objective of the safety information is to prevent personal injuries.
2.2.1 Explanation of the safety symbols used
In this instruction manual, the following safety symbols are used:
Risk of injury to persons
This symbol indicates hazards due to electrical voltages. There is
danger to life.
This symbol indicates general hazards. There is danger to life and
health.
Risk of damage to property
This symbol indicates possible damage to property. It is possible that
damage may occur to the drive, materials or the environment.
Other advice
This symbol indicates a useful general tip. If you follow it, you will find it
easier to operate the bed. This tip is provided to give you a better
understanding.
Please note:
The safety symbols used are not a substitute for the written safety information.
It is important therefore to read the safety information and follow the
instructions exactly!

Instruction Manual for Libra Care Bed
Page 11
2.2.2 Safety information for the operator
•Using this instruction manual, which must be provided with the bed, make sure
that every user and resident is instructed in the safe operation of the bed before
using it for the first time.
•Draw every user’s attention to the possible hazards that can arise if the bed is
improperly used. This applies in particular to the use of electrical drives and safety
sides.
•Please observe your obligations in accordance with the Medical Devices Operator
Ordinance (Medizinprodukte-Betreiberverordnung: MPBetreibV), to ensure that
this medical product is always operated safely and with no risk of danger to
residents, users or third parties.
•If the bed is in long-term use, test the functions and check for any visible damage
(see chapter 6.2) after a reasonable period of time (recommendation: once a
year).
•Only persons who have been properly instructed in its use must be allowed to
operate this bed.
•Make sure that substitute staff are also sufficiently well instructed in the safe
operation of this bed.
•If any additional devices (such as compressors for positioning systems) are
attached, ensure that these are securely fastened and are working properly. Pay
particular attention to:
oSafe routing of all loose connector cables, tubing etc.
oEnsuring that no multiple socket outlets are located under the bed (fire hazard
due to ingressing liquids).
ochapter 2.3.1of this instruction manual
If you have any questions or concerns, consult the manufacturer of the additional
equipment or Stiegelmeyer.
•Check that your staff are complying with the safety information.
•Allergic reactions when using upholstered components
Please note: The headboards, footboards and side-panels of the Libra
bed can be supplied in the upholstered version according to customer
specifications. If the resident is especially sensitive and tends to allergic
reactions, it is not possible, however, to completely exclude such
allergic reactions in the case of extended intensive skin contact with
upholstered parts. In these rare cases, please do not use the
upholstered parts.

Instruction Manual for Libra Care Bed
Page 12
2.2.3 Safety information for the user
•Route the cable of the switch mode power supply in such a way that it
cannot be pulled, driven over or damaged by moving parts when the
bed is operated.
•At regular intervals, carry out a visual inspection of the power supply
cable to check for mechanical damage (scuffing, exposed wires,
kinks, pressure points, etc.). Such a check should be performed:
•Whenever the cable of the switching power supply has been
subjected to any mechanical load, e.g. has been driven over by the
bed itself or by an equipment trolley, has been bent, stretched or
violently pulled due to the bed rolling away while still plugged into the
wall socket.
•Before plugging it back into the power socket after the bed has been
moved or relocated.
•Regularly by the user when the bed is in constant operation.
•If any damage or malfunction is suspected,
•Unplug the switch mode power supply immediately from the mains
socket,
•Indicate clearly that the bed is “Out of Order”,
•Take the care bed out of service, and
•Report this immediately to the operator responsible.
•Check the strain relief of the power mains cable regularly to ensure
that it is securely fixed.
•When using external electrical components such as patient lifts,
reading lamps, or compressors for positioning systems, ensure that
their power cables will not become entangled or damaged by moving
parts of the bed. This will prevent potential hazards due to electric
shocks, fire etc.
•Do not use multiple socket outlets placed loosely on the floor to
connect external electrical components. These could cause electrical
hazards due to damaged mains cables or the ingress of liquids.
•The cable for the switch mode power supply is fitted with a mains
cable holder. The holder is located on the mains cable itself
oBefore moving the bed, always make sure that you have
unplugged the switch mode power supply from the mains socket.
Hang it on the headboard with the mains cable holder to ensure it
will not fall off and the cable does not trail on the floor.

Instruction Manual for Libra Care Bed
Page 13
Danger of death due to electric shock!
•If a damaged cable continues to be used, this can lead to electric
shock, fire and other hazards as well as malfunctions.
•A damaged cable must be replaced immediately.
•Ensure that the operator instructs you in the safe operation of this bed.
•Each time before using the bed, check that it is in perfect working
order to prevent unnecessary hazards for the resident and delays to
work procedures (see also chapter 3.1).
•Adjust the mattress base to its lowest position before leaving the
resident unattended. In this way, you considerably reduce the risk of
injury to the resident due to a fall when getting in or out of bed.
•To safeguard the resident against unintentional motorised
adjustments, place the handset out of reach (e.g. at the foot end of
the bed) or lock the adjustment functions of the handset on the
control panel, if:
oThe resident is unable to operate the bed safely or to free
himself/herself from potentially dangerous situations.
oThe resident could be at risk due to unintentional motorised
adjustments.
oThe safety sides are raised (danger that the user's limbs could be
trapped when adjusting the backrest and thigh rest).
oChildren are left unsupervised in the room with the bed.
•Adjustments may then be made only by, or in the presence of, a
person who has received appropriate instruction.
•Ensure that no obstacles such as bedside cabinets, window sills,
sloping ceilings, floor cable ducts or chairs could impede adjustments
to the bed, to prevent damage to load-bearing parts of the bed and to
the obstacles.
•When not in use, stow the handset in such a way that it cannot
inadvertently fall off (hang it up by the hook). Make sure that the cable
cannot be damaged by moving parts of the bed.

Instruction Manual for Libra Care Bed
Page 14
2.3 PRODUCT DESCRIPTION
2.3.1 Intended use
•This bed is designed for positioning and transporting residents, as an aid to
diagnosing, monitoring, treating, and alleviating illnesses or compensating for
injuries or disabilities. For detailed instructions for use, see chapter 9.7
•This bed is suitable only for accommodating adult residents whose height is at
least 146 cm.
•The bed itself is not life sustaining or life supporting.
•The bed has no medical indication.
2.3.2 Use for the intended purpose
-The bed is intended for indoor use in senior residences and nursing homes and
comparable medical institutions with qualified personnel. For detailed instructions
for use, see chapter 9.5.
-Qualified personnel must be skilled in handling the beds and be thoroughly
conversant with the instruction manual.
-This bed may be operated without restrictions with a permanent maximum
load of 225 kg (resident and accessories). Symbol:
-The permitted weight of the resident depends on the total weight of the
accessories attached (e.g. respirators, infusions,) Symbol:
Example:
Weight of accessories
(incl. mattress)
Safe working load 225 kg:
Maximum permitted resident weight
10 kg
215 kg
40 kg
185 kg
-If the owner of the bed changes, the instruction manual must be handed over with
the bed.
-The bed with its castors is designed for being moved within the room, with the
resident in the bed.
-This bed is suitable for repeated use.
-This bed must only be used as a single bed.
-This bed may not be used in explosive environments caused, for example, by
cleaning agents or anaesthetics.
-This bed must not be used in combination with high-frequency surgical equipment.
-Before using the safety sides, assess and take into consideration the clinical
condition and particular physical build of the patient. Observe the special safety
information in chapter 4.5

Instruction Manual for Libra Care Bed
Page 15
This bed may only be used under the operating conditions described in this
instruction manual. Its use for any other type of application is deemed to be contrary
to the intended purpose.
2.3.2 Contraindications
•If used with safety sides, this bed is only suitable for residents
who do not fall below the following minimum body size/weight:
oHeight: 146 cm,
oWeight: 40 kg
oBody mass index
1
“BMI”: 17.
•Owing to the smaller limbs of patients with a body size/weight that is less than this,
there is an increased risk of entrapment between the open spaces of the safety
sides when safety side systems are used.
2.3.3 Side effects
Unless suitable measures are taken, residents who spend prolonged periods in bed
may develop decubitus.
2.3.4 Particular features of the bed
•Full-length safety sides on both sides
•Mattress base 200 x 90 cm, in four sections; external dimensions approx. 210 x
100 cm (depending on model)
•Electrical height adjustment range for mattress base: approx. 25 to 80 cm (for
Libra –movo variant approx. 28 to 83 cm)
•Electrical thigh rest adjustment from 0° to approx. 40°
•Electrical backrest adjustment from 0° to approx. 70°
•Electrical adjustment to a reverse-Trendelenburg position of approx. 16°
•Moves on four castors; each pair can be locked separately
1
Calculation of BMI = 󰇟󰇠
󰇟󰇠; example: a) 
  →ok!;
b) 
  →Not ok
Sticker on the
bed chassis

Instruction Manual for Libra Care Bed
Page 16
2.3.5 Special electrical equipment (optional)
-Electrical setting of Trendelenburg position: An external operating device (handset) allows
medical staff to place the resident in an emergency position whenever necessary.
-LED reading light: Energy-saving, no hazardous heating as with conventional lamps, resistant to
jolts and vibrations; approx. 50,000-hour lifetime of the LED bulb.
-Rechargeable battery for unrestricted electric emergency operation with full lifting capacity for
electric adjustments if a mains connection is not available: can be supplied ready integrated or can
be easily retrofitted for temporary use.
-Discreet LED night light under the bed provides orientation for the resident and prevents falls
from occurring at night.
2.3.6 Special mechanical equipment (optional)
–Mattress base 200 x 80 cm and 200 x 100 cm, in four sections
–Combined safety side (6): These combine the advantages of the familiar full-length and split safety
sides and provide maximum protection and flexibility in use. Can be quickly assembled or removed
without tools.
–Split safety sides on both sides (D): Our 2-stage telescopic safety sides can be adjusted across
a range of settings to suit individual needs and can be quickly assembled or removed without tools.
–Removable head and footboards: With Vario Safe system, split safety side and without safety
side, both the head and footboard can be quickly removed to provide easier access to the resident.
–Eight castors: With Libra –access Plus variant, lockable in pairs
–Thanks to its deep venting slits, the removable polypropylene hygiene mattress base is also
highly breathable. It can be easily placed on the mattress base and removed. It is also easy to care
for and can be cleaned with conventional cleaning agents.
–Removable comfort mattress base comprises 50 individual spring elements. These elements are
designed to mould themselves closely to the shape of the body and help to ventilate the mattress.
Their flexibility also ensures that the pressure is optimally distributed. The comfort mattress base
also significantly contributes to preventing pressure ulcers.
–Adaptable bed extension, extends the bed by approx. 10 cm or approx. 20 cm.
If full-length or combined safety sides are used, longer safety side bars must be fitted. In this case,
please consult our sales department (see chapter 6.4)
–Pillow holder, for attaching at the foot end; can be pulled out from under the mattress base
–Wall deflection roller effective in horizontal and vertical directions please observe (Please note:
Wall deflection rollers are fitted to the head and footboard. If the head and/or footboard are
removed (optional for Vario Safe and split safety sides), there is no longer any protection for the
bed and walls).
–Wall spacers, on the head end + sides; prevent damage to walls and on-site equipment when the
height of the bed is adjusted.

Instruction Manual for Libra Care Bed
Page 17
2.3.7 Materials used
For the most part, the bed is manufactured from steel profiles whose surfaces are finished
with a polyester powder coating or a metal coating of zinc or chrome.
The head and footboards and safety sides are made of wood or wood-based material with
sealed surfaces. All surfaces that can be touched during normal use have been tested for
bio-compatibility and are harmless to humans when in contact with the skin. Structural design
Mattress base
The mattress base is divided into a backrest, a fixed seat section, a thigh rest and a lower leg
rest. The rests are adjustable. The mattress base can be raised and lowered horizontally or
set to the reverse-Trendelenburg position with the foot end lowered (optional Trendelenburg
position also available).
Bed chassis
The chassis is constructed from welded steel tubing with an optimised scissor lift design and
is equipped with four castors (optionally with 8 castors for the Libra –floor access Plus
variant) which can all be locked in pairs on the foot and head end.
Safety sides
The bed has a full-length safety side to protect the resident from falling out of bed (2) or
optionally,
•a combined safety side (6),
•a split telescopic safety side (D).
The safety sides can be raised, one after the other, from the lowered position to provide
protection for the resident, and then lowered again when no longer required.
Electric drive system
The bed’s electrical drive system is first-error-secure, flame-resistant (UL94V-0) and consists
of:
•Electricity supply via:
oAn "external" switch mode power supply. The switch mode power supply consists
of a voltage transformer and a low-voltage connection cable. The voltage
transformer generates a protective low voltage that is safe for residents and
users. The switching power supply provides the control unit of all drives (motors)
with protective low voltage via a connection cable and a cable harness.
o(Optional) 230 V mains cable. In this case, the 230 V mains supply is
transformed to 24 V by the control unit.
•the central control unit. All drive motors and the handset are connected to the central
control unit via plug connections which work with protective low voltage.
•Electric motors for the backrest and thigh rest.
•Two electric motors for adjusting the height of the mattress base.
•A handset with a hook.

Instruction Manual for Libra Care Bed
Page 18
3 Putting into service
No electrical measurements are necessary prior to putting this bed into service for
the first time, since the bed has been tested by the manufacturer for electrical safety
and functionality and left our factory in perfect condition.
Before putting the bed into service for the first time:
•Remove all transport securing devices and packaging film.
•Clean and disinfect the bed.
Before putting the bed into service each time:
Check that:
-The bed has been cleaned and disinfected.
-The castors are braked.
-The power supply is compatible with the technical data of the bed (230 volt AC,
50/60 Hz).
-Easy access to the mains plug is ensured at all times so that the bed can be
disconnected from the mains, if necessary.
-The switch mode power supply unit is connected and the cable is routed in such a
way that it cannot be damaged through bed adjustments/being driven over.
-The switch mode power supply, drive cables and handset cable cannot be
damaged by the moving parts of the bed.
-This bed is not used in explosive environments caused, for example, by cleaning
agents or anaesthetics.
-Do not use this bed in combination with high-frequency surgical equipment.
-No obstacles such as bedside cabinets, supply rails or chairs will inhibit
adjustments.
-All adjustment functions are in proper working order and have been checked (see
chapter 3.1).
The care bed may be put into operation only after all these steps have been
followed!

Instruction Manual for Libra Care Bed
Page 19
3.1 CHECKLIST:INSPECTION BY THE USER
Check
WHAT ? HOW ?
OK
Not
OK
Description
of defect
Visual inspection of the electrical components
Handset
Damage?
Handset cable
Damage, cables routed
away from moving parts?
Switch mode power supply
Visual inspection of the mechanical components
Patient lifting pole, lifting
pole sleeves, grab handle
with strap (optional features)
Damage, cracks
Bed frame
Damage, deformations?
Mattress base
Damage?
Wooden surround
Damage, splinters?
Safety sides
Damage, deformation,
splinters?
Functional check of the electrical components
Handset, locking functions
Functional test
Rests
Functional test
Height adjustment
Functional test
Reverse-Trendelenburg
position
Functional test
Functional check of the mechanical components
Castors
Braking, moving
CPR release of backrest
Test according to
instruction manual
Safety sides
Locking in place,
releasing?
Accessories (e.g. patient
lifting pole, grab handle)
Suitability, secure
fastening, damage?
Inspector’s signature:
Inspection result:
Date:
If damage or a malfunction is suspected, the care bed must be withdrawn
from service immediately and disconnected from the mains supply until the
defective parts have been repaired or replaced!
Report this immediately to the operator!

Instruction Manual for Libra Care Bed
Page 20
3.2 LOCATION REQUIREMENTS
•There must be sufficient room available to accommodate the bed’s entire range of
adjustments. Furniture, window sills, must not be in the way.
•Before using the bed on parquet flooring, check whether the castors could leave
marks on the parquet varnish. The bed can be used on tiles, carpet, linoleum or
laminate flooring without causing any damage.
•A properly installed mains socket must be available as close as possible to the
head end of the bed. Position the bed so as to allow easy access to the power
plug at all times, so that the bed can be disconnected from the mains, if
necessary.
Features of the switch mode power supply
The switch mode power supply is simply
plugged into an electrical socket.
The outlet cable must hang downwards.
The mains socket you wish to use for the switch mode power supply
must NOT be under the bed.
oOtherwise, the moving mattress base frame may rip the switch
mode power supply out of the mains socket during horizontal
adjustments.
oIrreparable damage to the switch mode power supply could be
caused and a short-circuit in the electrical socket could occur.
Be careful when moving the bed away: Ensure that the cable is
long enough; unplug the switch mode power supply.
Take care when adjusting the height: Maintain a sufficient
distance at the side between the bed and the switch mode power
supply to avoid damaging it. (Use a wall spacer, if necessary)