STILFORD S2 Electric Sit Stand Desk User manual

User Manual
1. nitial Setup
After the initial assembly of the desk or if the display shows either of “E10, E16,E20 or E60”,
press the button for 5 seconds until it shows , the desk will automatically
move down to the lowest and rebound back up. The learning process & stroke reset
is then finished and will display the lowest height
2. Lifting
The desk will go up and down when pressing or .
3. Height memory setting
Move the desk up or down to a desired position. Press the button after which the
display will blink, then press a numeric key ( ) to save the desired height
to the corresponding preset position. The display will stop blinking and exit the memory
mode if there is no numeric key pressed within 5 seconds.
Once you have saved the desired you can press that numeric key to automatically
move the desk to the saved height.
4. Setup Mode
1. Press and hold the button for 5 seconds, display will show “S--" and blink.
2. Press the button to move through the below setup menu functions,
then press
to select menu,and press "S" into menu.
Unit（）: Display height on screen in centimeters or inches;
Brightness（ ）: Brightness of the controller;
Stilford S2 Electric Sit Stand Desk
position
(072) .
position
height
,,
1/4
I

Beep（ ）: Turn on/off beep sound;
Collision Force（ ）: Collision protection sensitivity;
To navigate through the setup menu use the below buttons：
Backspace key (back to previous menu) or Exit Setup Mode
Tab switch
Enter key (enter to next menu or confirm the current operation)
If there is no numeric key pressed within 20 seconds the Setup Mode will be exited.
2/4
Main menu interface Submenu
interface Description
CM
Unit Inch
Select height unit to be displayed in cm or
inches.
or to choose the height unit, and press
to confirm and save it. The system will exit after
2 seconds.
Low
Normal
Brightness
High
Select brightness setting of controller. Use or
to choose the and press
to confirm and save it. The system will exit after
2 seconds.
Off
Beep On
Turn on or off the beep sound. Use or to
choose sound on or off, and press to
confirm and save it. The system will exit after 2
seconds.
Off
Light
Normal
Collision Force
Heavy
Select collision protection sensitivity. Use or
to choose the sensitivity, and press to
confirm and save it. The system will exit after 2
seconds.
resistance
resistance
resistance
brightness level,

3/4
5. Protection codes and warnings
E16 Block protection
HOT Overheat protection
The desk has entered the overheat protection after operating for a long time. Wait
for "HOT" to disappear and a number to show on the screen, then the desk will
E10
Motor fault protection
Power off the desk. Remove desktop for easy access to cables. One by one unplug
is each cable then reconnect ensuring all are connected in correct location based on
the Assembly Instructions. Turn power on and follow the Initial Setup process.
E20 Overload protection
The desk has more weight than the intended weight capacity. Remove objects from
the desktop to ensure the desk is not overloaded with weight then power the desk
and on again or follow the Stroke Reset Process.
E31 Undervoltage protection
Power the desk off and make sure the voltage between 110 to then power on
E32 Overvoltage protection
E60 Out-of-step protection
Check and ensure the motors of each leg are at an identical height and their
connection to the controller is correct as per the Assembly Instructions, then power
the desk off and on again. Press down button,"E60" shown on the screen, then
function normally.
V
V
and follow the Initial Setup process (press and hold down button for 5 seconds).
240
Power the desk off and make sure voltage correct from 110 to then power onV
V
and follow the Initial Setup process. (press and hold down button for 5 seconds).
240
follow the Initial Setup process (press and hold down button for 5 seconds).
off
1. Please check if the desk is tilted, if tilted please make sure it is adjusted to flat
surface then press up or down button for height adjustment.
2. Message "E16" will flash on the screen for 5 to 10 seconds if the desk has been hit
by an object during operating. Please ensure you remove the object away from the
desk then press up or down button to adjust your desk height.
3. If error message "E16" continuous to flash, please unplug the desk and wait for
at least 1 minute before you plug it back in. will also need to check and ensure
all cables are connected properly follow by the assembly instructions. Once you have
done the check, plug the desk back into the powerpoint and start the Initial Setup
process by press down arrow for 5 seconds until it shows "rES", the desk will
automatically move down to the lowest position and rebound back up.
If above step can not solve the problem please follow echanical Reset on page 4.
If above step can not solve the problem. Please follow the echanical Reset on page 4.
If above step can not solve the problem please follow echanical Reset on page 4.
If above step can not solve the problem please follow the echanical Reset on page 4.
You
M
M
M
M

4/4
6. Mechanical Reset
1. Press "S" button for 3-4 second until it shows "S - - " and flash.
2. Press "S" button 1 time to go into the menu showing "Un".
3. Press "up" arrow button 2 times until it shows "rSE".
4. Press "S" button again the screen will now show "OFF".
5. Press "up" button again until it shows "ON".
6. Press "S" button again and "ON" will stop flashing. Press "S button again and screen will
now show the current height of the desk.
7. Hold the "down" arrow for the desk to move down. The higher leg should come down
first until it is at the same height as lower leg. Then screen will now show "E20" then
show current height of desk.
(If you press "down" arrow and the desk still will not move, please try to hold down the
"S" button for 3-4 second until the desk goes down).
8. Release the "down" arrow button until the screen shows "rES", desk will automatic go
down again until it reaches to the lowest position.
9. You can use the up and down arrow to adjust your desk height as per normal.
7. The default lowest height is 72cm.
If you want to adjust lowest position to 67cm please follow below step.
1. Press "S" button for 3-4 second until it shows "S - - " and flash.
2. Press "S" button 1 time to go into the menu showing "Un".
3. Press "down" arrow button 4 times until it shows "SH".
4. Press "S" button again the screen will now show "0".
5. Press "down" button again until it shows "L".
6. Press "down" button again until it shows "072".
7. Press "down" button until it shows "067"
8. Press "S" button 1 time to confirm the lowest position.
9. Press "down" button until desk to "067"