Stirling STR-FL80 User manual

AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
8kg Front Load Washing Machine
Model Number STR-FL80
INSTRUCTION MANUAL

2AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
Welcome
Congratulations on choosing to buy a STIRLING®product.
All products brought to you by STIRLING®are manufactured to the highest standards
of performance and safety and, as part of our philosophy of customer service and
satisfaction, are backed by our comprehensive 3 Year In Home Warranty. We hope you
will enjoy using your purchase for many years to come.

3
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
Contents
02 Welcome
04 Warranty Details
05 General Safety Instructions
09 Product Overview
10 Installation
16 Getting Started
18 Instructions
25 FAQs and Troubleshooting Guide
28 Other Useful Information
35 Repair and Refurbished Goods or Parts Notice

4AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
The product is guaranteed to be free from defects in workmanship and parts for
a period of 36 months from the date of purchase. Defects that occur within this
warranty period, under normal use and care, will be repaired, replaced or refunded
at our discretion. The benefits conferred by this warranty are in addition to all
rights and remedies in respect of the product that the consumer has under the
Competition and Consumer Act 2010 and similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and to compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.
YEAR IN HOME
WARRANTY
3
8kg Front Load Washing Machine
Warranty Details
REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION

5
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
General Safety Instructions
Electrical safety and cord handling
• Voltage: Before connecting and turning on the appliance, ensure the electrical volt-
age and circuit frequency correspond to those indicated on the appliance rating label.
• Power supply system: As the maximum current through the unit is 10A when you
are using the heating function, make sure the power supply system (current, power
voltage and wire) at your home can meet the normal loading requirements of electri-
cal appliances.
• WARNING! Only connect the washing machine to a grounded (earthed) electrical
outlet. Do not overload the wall outlet, as overloading can result in fire or electric
shock. Insert the power plug securely.
• Protect from moisture: To avoid electric shock, fire and malfunction, do not install
this machine in a damp place. Do not pull out or insert the plug with wet hands or
bare feet. Do not expose the appliance, cord or plug to rain, moisture or other liquid.
• Power cord: Do not kink or damage the power cord, and position it out of the way so
no one steps on or places anything on the cord or against it.
WARNING! Do not use the machine if the cord or plug is damaged to avoid an
electric shock, short circuit or fire. If the cord is damaged, it must be replaced by the
manufacturer’s service agent or a properly qualified person in order to avoid a hazard.
IMPORTANT SAFETY INSTRUCTIONS
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
Read this manual thoroughly before first use, even if you are familiar with this type
of product. The safety precautions enclosed herein reduce the risk of fire, electric
shock and injury when correctly adhered to. Keep the manual in a safe place for future
reference, along with the completed warranty card and purchase receipt. If applicable,
pass these instructions on to the next owner of the appliance.
Always follow basic safety precautions and accident prevention measures when
using an electrical appliance, including the following:
Pay particular attention to safety advice following the words:
DANGER, WARNING and CAUTION.
These words are used to alert you to a potential hazard that can seriously injure
you and others. The instructions will tell you how to reduce the chance of injury
and let you know what can happen if the instructions are not followed.
DANGER means that failure to read this safety statement may result in severe
personal injury or death.
WARNING means that failure to read this safety statement may result in
extensive product damage or serious personal injury.
CAUTION means that failure to read this safety statement may result in
minor or moderate personal injury, property or equipment damage.

6AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
General Safety Instructions (Cont.)
• CAUTION! Use of a power adaptor or extension cord is not recommended. However,
if you must use an extension cord, make sure it is earthed, has been approved and
has the same or higher electrical rating (voltage and power) as the product. Arrange
the extended cord so that it is not subjected to splashing or ingress of moisture.
• After use: Always unplug the appliance and turn off the water after use.
• Disconnect: Unplug the washing machine from the power supply before cleaning,
servicing, maintenance or moving the appliance. Pull by the plug, not by the cord.
• Keep openings clear: Do not insert any objects into ventilation or similar openings.
• No timer: The appliance is not intended to be operated by means of an external
timer or separate remote control system.
• RCD: Unless your home is already fitted with a residual current device (safety
switch), we recommend installing an RCD with a rated residual operating current
not exceeding 30mA to provide additional safety protection when using electrical
appliances. See your electrician for professional advice.
Installation
• WARNING! This appliance is extremely heavy. Transport with care! A team lift
or mechanical aid is required when moving the machine. Do not hold the washing
machine by the door or any other protruding part while lifting or transporting it.
• Freestanding use only: This appliance is not to be built in.
• Do NOT install the appliance:
- Outdoors or in a damp or wet environment (such as a bathroom).
- In areas where caustic or explosive gases are present.
- Behind a lockable door, a sliding door or a door with a hinge on the opposite side to
that of the washer in such a way that a full opening of the washer door is restricted.
• Installation surface: This washing machine must be installed on a flat, even and
stable ground to avoid overturning during use or maintenance. Do not place it on
carpet. If the machine must be positioned on carpet, place a plastic mat underneath
the machine and make sure any ventilation openings in the base are not obstructed.
• Clearances: Ensure that there is a distance of at least 200mm between the appliance
enclosure and any external heat sources, such as appliances containing heating
elements.
• Installation: Make sure that all water and electrical connections are made by
qualified persons only, observing local safety regulations and following the installation
instructions in this manual (refer to “Getting Started: Installation”, pages 10–15). Do
not use the appliance until it is fully installed.
• Water connection: Connect the washing machine to the water mains using new
hose sets. Do not reuse old hose sets. The required water pressure is 0.03MPa (min.)
to 1.0MPa (max.).
CAUTION! This machine has only one inlet for water (cold). Do not connect it to the
hot water supply.

7
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
General Safety Instructions (Cont.)
• Drainage: Do not allow the water drained out of the appliance to accumulate.
• Electrical connection: During installation, the power cord must not be excessively or
dangerously bent or flattened. The plug must be accessible after installation.
• Ventilation openings: Do not cover any air inlet or exhaust openings.
• Misuse: Improper installation or faulty use may result in the risk of fire, electric shock
and/or injury. We accept no liability for any eventual damages or injury caused by
improper installation, misuse or noncompliance with these instructions.
Usage conditions and restrictions
• Domestic use only: The appliance is designed for private household use only. It is
not suitable for commercial, industrial or trade use.
• Intended purpose: This washing machine is designed for washing domestic
quantities of textiles suitable for machine-washing. Do not use the machine for
anything other than its intended purpose, and only use it as described in this manual.
• No outdoor use: Do not operate the appliance outdoors.
• Usage restriction: This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
• Children: Supervise children to ensure they do not play with the appliance. Close
supervision is necessary when any appliance is used by or near children. Do not
allow children (or anyone else) to climb up and sit on top of the washing machine.
• Handling: Handle the washing machine with care. Do not place or store flammable
items or heavy objects on top of the machine. Do not sit on the top cover.
• Door handling: Handle the door with care. Do not lean against the machine door.
Do not let children swing from the door. Do not close the door with excessive force.
If you find it difficult to close the door, please check and ensure that the clothes are
properly loaded and well distributed.
• Before loading the washing machine, make sure that:
- No young child or pet has climbed into the drum.
- The water inlet hose is properly connected and the tap is turned on.
- All pockets of clothing to be washed are empty. Hard, sharp objects such as coins,
safety pins, paper clips, bra wires, nails, screws or stones can cause extensive
damage to the appliance and block the pump. Any damage or malfunction resulting
from foreign objects is not covered by your warranty and may lead to expensive
repairs.
• Do NOT wash the following items in the washing machine:
- Rain jackets, raincoats, fishing coats and similar waterproof clothes or covers.
- Carpets or floor rugs.
- Underwire bras (damage to the appliance can result if metal reinforcements come
loose during the washing cycle).

8AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
General Safety Instructions (Cont.)
- Clothes that have any residues of flammable materials, as this may result in fire
or explosion. For example, articles that have been cleaned in, washed in, soaked
in, or dabbed with industrial chemicals, or combustible or explosive substances
(such as wax, oil, paint, petrol, alcohol, degreasers, dry-cleaning solvents,
kerosene, etc.). Items containing such substances must be washed by hand or
rinsed thoroughly before they may be machine-washed.
• Flammable, explosive or toxic substances must not be used as washing
detergents or for cleaning the machine.
• Capacity: Do not overload the washer; its maximum capacity is 8kg (max. weight of
dry wash load).
• Water intake: Never refill the water by hand during washing.
• After use: After the program is finished, wait until the drum has stopped spinning
and the door lock icon is no longer lit before opening the door. If water is still visible,
do not attempt to open the door. Do not add or remove clothes while the drum is
spinning.
• Disconnect the water and power supplies after use.
CAUTION: Hot!
• During a hot wash, the door window may become hot. Do not touch it, and ensure
to keep children and pets away from the machine during operation.
• Be careful of burning when the machine drains hot washing water.
Cleaning and maintenance
• Disconnect: Before cleaning or carrying out maintenance, always unplug the
appliance from the power supply.
• CAUTION: After each wash, clean the door and the door seals and remove any
threads, lint or foreign objects. Also check the detergent drawer and clean out
detergent residues.
• Keep parts clean: Regularly clean the power plug to remove dust and dirt and avoid
contact failure.
• Do not open the housing: The washing machine has no user-serviceable parts
contained within. Do not attempt to repair, dismantle or modify it. Repairs made by
inexperienced or unqualified persons may cause injury and/or make more serious
repairs to the appliance necessary.
• Service: This appliance should only be serviced by authorised service personnel,
and only genuine spare parts should be used. To purchase spare parts, please
contact our after sales support centre.

9
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
Product Overview
5
6
7
2
3
Scope of delivery
A Top load washing machine
1 Door
2 Detergent drawer
3 Program dial
4 Control panel with LED display
5 Wash/spin drum
6 Pump filter cover
7 Adjustable legs
B Other inclusions (not shown)
Transport hole plugs (4)
Cold water supply hose
Drain hose and hose support (attached to
the rear of the machine)
Wrench
Instruction manual, Quick start guide,
Warranty certificate
NOTE: Due to continued product improvement, images and illustrations in this
manual may vary slightly from the product purchased. All images in this manual are for
reference purposes only. Parts are not necessarily pictured to scale.
1
4

10 AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
Installation
Unpacking the washing machine
CAUTION: EXTREMELY HEAVY!
• A team lift or mechanical aid is required when moving this appliance.
• Keep the washing machine as upright as possible during transportation.
• This product has been packaged to protect it against transportation damage.
Remove all packaging materials from inside the drum and around the appliance.
• Keep the original packaging carton and materials in a safe place. It will help prevent
any damage if the product needs to be transported in the future, and you can use
it to store the appliance when it is not in use. In the event that the carton is to be
disposed of, please recycle all packaging materials where possible.
• Plastic wrapping can be a suffocation hazard for babies and young children, so
ensure all packaging materials are out of their reach and disposed of safely.
• Carefully lift the washing machine and remove the
base packing. Make sure the base protection device is
removed together with the bottom piece (Fig. 1). If not,
lay the unit down on its side, then remove the small
foam piece from the base of the unit manually.
• Remove any tapes securing the cord and drain hose.
• Remove all accessory parts from the drum.
Checking the package contents
• Check all parts of the package against the scope of
delivery list on the previous page and ensure you have received all items.
• Check the washing machine for any damage from transportation. Unwind the power
cord to its full length and inspect it for damage. Do not use the appliance if the
appliance or its cord has been damaged or is not working properly. In case of
damage, of if anything is missing, contact our after sales support centre for advice
on examination, repair or return of the damaged product.
• Read this manual to familiarise yourself with all the parts and operating principles of
the wash. Pay particular attention to the safety instructions on the previous pages.
Fig. 1
WORKING CONDITION
• Do not operate the washing machine in temperatures outside its normal working
condition (0–40°C). Using it in temperatures below 0°C may damage the machine’s
inlet valve and draining systems.
• If the machine is stored in an area where the temperature drops to below 0°C,
transfer it to an area with a warmer ambient temperature before use and ensure no
residual water is frozen in hoses and pipes.

11
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
Installation (Cont.)
Removing the transport bolts
WARNING!
• Before installing the washing machine, you must remove the transport bolts from
the back of the housing and cover the holes with the transport hole plugs provided.
• The four bolts hold the drum in place during transport but they must be
removed before use so the drum can move during the wash and spin cycles.
Leaving the bolts installed will result in strong shock and noise during use,
malfunction and serious damage to the machine.
Selecting the location
WARNING!
• Stability is important to prevent the washing machine from moving during operation.
• Make sure that the machine does not stand on the power cord.
Before installing the appliance, make sure the location meets the following requirements:
• Dismantle the four bolts from the back of the washing
machine using the supplied wrench (Fig. 2).
• Keep the bolts in a safe place; you will need them
again when moving the machine, if you move house.
(When required, the transport bolts must be reinstalled
into the machine by an authorised service agent; call
our after sales support centre for advice.)
• Cover the holes with the supplied transport hole plugs.
• The surface is rigid, dry and level – if it is not level,
please adjust the levelling legs (see page 12).
• The position is protected from direct sunlight, water
and weather.
• There is sufficient ventilation.
• There is 100mm space between any walls and the
furthest protruding part of the machine (Fig. 3).
• The room temperature is above 0°C.
• The position is at least 200mm from heat sources.
• The machine will not stand on the power cord.
• The area is not carpeted (if this cannot be avoided, place a plastic mat underneath
the machine and make sure any ventilation openings in the base are not obstructed).
Do NOT install the appliance:
• Behind a lockable or sliding door, or a door with a hinge on the opposite side of the
machine, in such a way that a full opening of the appliance door is restricted.
• In a tight-fitting cabinet.
Fig. 2
Fig. 3
100mm

12 AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
Installation (Cont.)
1
2
Lock nut
Foot
Fig. 4
Levelling the machine
• Place the machine on solid, dry and level ground.
• First check if the legs are closely attached to the cabinet. If not, please turn them
to their original positions and tighten the nuts with a wrench.
• To determine whether levelling is necessary,
place a spirit level on top of the washer and
hold it upright against the housing to identify
any inclinations (Fig. 4).
• To find out which leg needs to be adjusted,
press the four corners of the top cover in
sequence. If the washing machine is not
stable when being pressed, this leg needs to
be adjusted.
• Loosen the lock nut with the wrench and turn
the leg by hand until it makes close contact
with the floor.
• Turn the lock nut clockwise to raise the leg
and anticlockwise to lower it (Fig. 5-2, 5-3).
• To lock the foot, hold the leg with one hand
and fasten the nut closely to the cabinet with
the other.
• Use the same steps to shorten or lengthen
any other leg that needs adjusting.
WARNING!
It is very important to level the washing machine carefully, especially if your floor is
uneven. Failure to do so may result in the machine shaking and moving during the
spin cycle, or out-of-balance problems.
Foot
Lock nut
Fig. 5
WARNING!
The lock nuts on all four feet must be screwed tightly against the housing (Fig. 5-4).

13
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
Installation (Cont.)
Connecting the water supply hose
WARNING!
• To prevent leakage or water damage, make sure to follow the instructions in this
section when connecting the washing machine to your water supply.
• Do not kink, crush, modify or sever the water inlet hose.
Connect the supplied cold water supply hose to an ordinary laundry tap following the
instructions below:
• Attach straight end of the hose to your cold water tap. While holding the hose, turn
the coupling nut clockwise to tighten securely by hand. [If you need to detach the
hose, first turn off the tap, then turn the nut anticlockwise to loosen (Fig. 6).]
• Attach the curved end of the hose to the inlet valve of the washing machine.
Tighten the coupling nuts securely by hand (Fig. 7).
• Turn on the taps and check for leaks. In case of leakage, repeat the connection
steps above, or tighten the nuts more firmly. If your water pressure is strong, close
the water tap completely, then open it slightly.
CAUTION!
• When tightening the coupling nut, take care not to damage the water inlet valve
joint. Apply force evenly and do not twist the water inlet valve.
• Use only the new (supplied) hose with your new appliance. Do not use a hose
from an existing machine, or one that has been used previously.
Water inlet valve
Turn clockwise to tighten Turn anticlockwise to
loosen
Fig. 7
Fig. 6

14 AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
Installing the drain hose
Installation (Cont.)
WARNING!
• Do not kink or protract the drain hose.
• Position the drain hose properly in order to prevent water spillage onto the floor
and potential damage.
• Never immerse the end of the drain hose in water.
The drain hose is installed at the back of the machine. For drainage of the washing
water, you can install the other end of the hose three different ways, as illustrated:
• Lead the drain hose into a drain spout (Fig. 8).
• Affix the drain hose into a branch drain pipe of the laundry sink (Fig. 9).
• Lead the drain hose into a sink/basin, using the drain hose support at the back of
the machine, and secure it with a rope or tie (Fig. 10). To ensure proper drainage
when the washing machine is in use, the height of the drain hose must not be higher
than 100cm above ground.
WARNING!
• If the drain hose is too long, do not force it into the washing machine as it will cause
abnormal noise.
• Never lay down the drain hose as water will be discharged.
• Be sure the drain hose is properly routed so it will not kink or lift off the sink.
• Leave the drain hose affixed to the back of the machine; do not remove the hose
buckles.
• When the washing machine is not in use, you may leave the drain hose at the back
of the machine, using the hose clips to keep it in place.
Fig. 8 Fig. 9
Drain
spout
100cm
Fig. 10 Basin
100cm
Max. 100cm

15
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
WARNING! This appliance must be earthed!
In the event of a malfunction or breakdown, earthing will reduce the risk of an
electric shock by providing a path of least resistance for the electric current.
This appliance is equipped with a cord having an equipment-earthing conductor
and an earthing plug. The plug must be plugged into an appropriate outlet that is
installed and earthed in accordance with all local standards and requirements.
Do not modify the plug under any circumstances. If the plug does not fit your
outlet, consult a licensed electrician and have the outlet changed.
Electrical connection
Installation (Cont.)
Power supply system
• As the maximum current through the unit is 10A when you are using the heating
function, make sure the power supply system (current, power voltage and wire) at
your home can meet the normal loading requirements of electrical appliances. The
electrical voltage and circuit frequency are listed on the appliance rating label.
• WARNING! Only connect the washing machine to a single, grounded (earthed)
electrical outlet. Do not overload the outlet, as overloading can result in fire or electric
shock. Insert the power plug securely. Do not use a power adaptor or extension cord.
Electrical installation advice
• To avoid electric shock, fire and malfunction, do not install this machine in a damp
place. Do not pull out or insert the plug with wet hands or bare feet. Do not expose
the appliance, cord or plug to rain, moisture or other liquid.
• Do not kink or damage the power cord, and position it out of the way so no one steps
on or places anything on the cord or against it.
• Ensure the washer is unplugged from the power supply before installation. The plug
must be accessible after installation.
• CAUTION! Use of a power adaptor or extension cord is not recommended. However,
if you must use an extension cord, make sure it is earthed, has been approved, and
has the same or higher electrical rating (voltage and power) as the product. Arrange
the extended cord so that it is not subjected to splashing or ingress of moisture.
• Unless your home is already fitted with a residual current device (safety switch), we
recommend installing an RCD with a rated residual operating current not exceeding
30mA to provide additional safety protection when using electrical appliances. See
your electrician for professional advice.
• All electrical connections must be made by qualified personnel, and all instructions in
this manual as well as local safety regulations must be observed.

16 AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
Getting Started
Quick start guide
The pictorial quick start guide below only contains basic information. For detailed
operating instructions, please read the corresponding content on the following pages
of this manual.
CAUTION!
• Make sure the washing machine is properly and securely installed before using it.
• Before using the washing machine for washing clothes, run a complete washing
cycle without clothes, using the drum clean program.
Preparation (Fig. 11)
Washing (Fig. 12)
After washing (Fig. 13)
Unplug Open door Unload Close tap
234
1
Plug in Open tap Load Close door Add detergent
Deter-
gent
Detergent
Select program Select option Start up
(or skip for default)

17
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
Getting Started (Cont.)
Control panel (Fig. 14)
1 Wash programs
2 Program dial: Turn the program dial to switch on the machine and select your
desired wash program.
3 Stand-by position: Turn the dial to the stand-by position to switch the machine to
stand-by (it switches to stand-by automatically at the end of the program, but the
dial remains on the selected program position).
4 LED display: Shows the settings, estimated time remaining, options, codes, etc.
5 Temp. button: Press to adjust a program’s default temperature (if available). Press
and hold this button to set the child lock function.
6 Spin Speed button: Press to adjust a program’s default spin speed (if available).
Press and hold this button for at least 3 seconds to mute the buzzer.
7 +Rinse button: Press to add an additional rinse (if available).
8 Delay Start button: Press to set the delay function (up to a maximum of 24 hours).
9 Start/Pause button: Press to start the program or to pause it.
Display (Fig. 15)
The numbers on the LED display (A) show the remaining time, delay time, number of
extra rinses, water temperature or spin speed.
Icons will illuminate when you have the buzzer (B) muted, child lock (C) set or door
lock (D) activated.
5
1
A
3 1
24
67 8 9
B C D

18 AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
Before first use
Before using the washing machine for the first time, please review the following
important points and make sure that:
• All transit bolts are removed.
• The washer is stable and level. If necessary, adjust the levelling legs to stabilise the
washer (see page 12).
• The water supply hose is properly installed (see page 13).
• The power plug is firmly inserted into a nearby power point and power is switched
on to the outlet.
• The water tap is open.
• The drain hose is properly installed and secured into the laundry sink or into a
drain spout (see page 14).
• Before using the washing machine for the first time, run a complete drum
clean program without laundry items and without any detergent.
Instructions
Door lock
The door of the front load washing machine locks automatically when the machine is
working. It cannot be opened during the wash without first pausing the wash program.
Unlocking the door
• When the machine is working, press the Start/Pause button to pause the program.
Wait until the door lock icon extinguishes on the LED display. The door may then be
unlocked when the drum has stopped spinning (unless the water temperature is high).
• Suds may flow out of the open door if it is opened during the wash cycle. Beware of
suds escaping from the machine and have a cloth/towel ready for catching spills.
NOTE: If you remove the power plug while the machine is working – or when the
electricity supply is cut during operation due to a power outage – the door will not
unlock automatically.
Child lock
The child lock function lets you lock the door and buttons to prevent unauthorised
operation of the machine by young children.
1. To set the child lock, power must be supplied to the machine.
2. Press and hold the Temp. button for approximately 3 seconds until a buzzer
sounds. The door and all buttons will now be locked.
3. To cancel the child lock, repeat this action.

19
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
The middle compartment is for fabric softener. It will be dispersed through the
washing during the last rinse cycle. Concentrated fabric softeners should be
diluted as required. Do not exceed the full mark line.
The detergent compartments on the left and right side of the drawer are for
low-sudsing detergent. If you are using powder detergent, we recommend you
dissolve it in some water before adding it to one of the two compartments.
Liquid detergent and bleach may also be added to these detergent compart-
ments, but they must be diluted according to the instructions on the bottle.
Never pour bleach directly onto the washing or into the compartment, as this
can cause stains or fading of coloured garments.
Detergent recommendations
• Only use low-sudsing detergent and clothing care preparations that are
suitable for use in a front load washing machine, or in a top and front load
machine. Detergents for top load machines are unsuitable because they tend to
produce too much suds, which may cause overflowing from the detergent drawer.
• Use detergent in the amounts recommended on the detergent packaging. Dosage
depends on your amount of washing, the degree of soiling, water hardness and
the washing performance of your detergent. Using too little detergent will give poor
washing results, but too much will affect rinse performance and may cause overflow
of suds, which could interfere with machine operation. Do not overfill detergent!
• Pull open the detergent dispenser drawer and add detergent, as illustrated (Fig. 16)
and described below.
WARNING!
• Do not use flammable and explosive or toxic solvents, petrol, alcohol or other
chemicals in the machine.
• Keep detergents and clothing care preparations out of reach of children.
Instructions (Cont.)
Fig. 16
Deter-
gent
Detergent

20 AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-FL80 PRODUCT CODE : 11969 11/2019
Table 1: Programs
Instructions (Cont.)
# This program was used for energy efficiency testing to the standard. Rinse numbers cannot be adjusted when used on default settings.
Program Application
Max.
Load
(kg)
Default
rinses+
(extra)
Default Temperature
(default + temp. range)
(°C)
Default
Time
(hr:min)
Spin Speed (RPM)
(default + extra)
Cotton Eco # A warm water eco program with an extra long
washing time used for energy efficiency testing 8.0 3
2+ (0–4)
40
(Cold - 30 - 40 - 60) 5:39 1400
(400 - 600 - 800 - 1000 - 1200 - 1400)
Cotton
Normally soiled cottons, linens or cotton
mix fabrics (e.g. table linen, towelling,
underwear, T-shirts etc.)
8.0 2+ (0–4) 40
(Cold - 30 - 40 - 60 - 80) 1:21 1400
(400 - 600 - 800 - 1000 - 1200 - 1400)
Mixed Wash A warm water program for a mixed load of
synthetic and cotton textiles 6.0 2+ (0–4) 40
(Cold - 30 - 40 - 60) 1:18 1000
(400 - 600 - 800 - 1000 - 1200)
Jeans A program for denim jeans or similar hard-
wearing cotton clothing 5.0 2+ (0–4) 30
(Cold - 30 - 40) 1:08 1000
(400 - 600 - 800 - 1000 - 1200)
Woollens
A specially gentle program for machine-
washable wool or wool-blend textiles.
Designed to prevent shrinkage.
2.0 2+ (0–4) Cold
(Cold - 30 - 40) 1:04 600
(400 - 600 - 800)
Synthetics A gentle program for synthetic or synthetic
blend textiles 6.0 2+ (0–4) 30
(Cold - 30 - 40) 1:07 800
(400 - 600 - 800 - 1000)
Down Jackets A gentle program for puffer (down-filled)
jackets, vests and similar clothing 2.0 3+ (0–3) 30
(Cold - 30 - 40) 1:31 800
(400 - 600 - 800 - 1000)
Quick Wash An extra short program for a few lightly
soiled items 1.0 1+ (0–5) Cold
(Cold - 30) 0:16 800
(400 - 600 - 800 - 1000 - 1200 - 1400)
Colours A cold program for brightly coloured items 3.0 2+ (0–4) Cold 1:00 600
(400 - 600 - 800)
Delicates Delicate, washable textiles made from syn-
thetic, rayon, viscose or blended fibres 3.0 2+ (0–4) Cold
(Cold - 30 - 40) 0:55 400
(400 - 600)
Shirts Cotton or mixed fibre shirts and blouses 3.0 2+ (0–4) 30
(Cold - 30 - 40 - 60) 1:05 800
(400 - 600 - 800 - 1000)
Hot A very hot water wash for items requiring
particularly high levels of hygiene 4.0 3+ (0–3) 80
(60 - 80) 2:23 800
(400 - 600 - 800 - 1000 - 1200 - 1400)
Rinse + Spin Separate rinse program with spin 6.0 1+ (0–5) –0:21 1000
(400 - 600 - 800 - 1000 - 1200 - 1400)
Spin Separate spin program with selectable
speed. Drains water before spinning. 6.0 – –0:12 1000
(400 - 600 - 800 - 1000 - 1200 - 1400)
Drum Clean A drum cleaning program designed for use
without laundry items –– – 2:19 –