Stompa T1035-02 User manual

White - 4ft6 Bed with Slats
Dimensions
Width - 148cm
Depth - 204cm
Height -109cm
Issue 1 - 22/10/10
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0844 8008475
Assembly Instructions - Please keep for future reference 6564942
Use this position if adding
the Under bed Storage Unit
Ladder can be fitted right or left side.
350
POSITION 2
254
POSITION 1 Use this position if adding
the Truckle/drawer
This is a universal bunkbed that can be used on its own or
with one of the 2 optional storage solutions show below
- Detachable bunkbed
80364516
208
,
2cm
105
,
1cm
161
,
2cm
80364516 NR331-V6 Issue 3 - 12/07/12
1

· Warning! Children can become trapped
between the bed and the wall.
To avoid risk of serious injury the
distance between the top safety barrel
and the wall shall not exceed 75 mm or
shall be more than 230mm.
Glue safety - Take care when using glue, please follow the advice below
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Care and maintenance
• The bunk bed meets the european
EN 747-1:2012 standards for security
and durability.
• The bunk bed meets the Bunk Beds
(Entrapment Hazards) (Safety)
Regulations 1987
Before Starting Assembly
• Only clean using a damp cloth
and mind detergent, do not use
bleach or abrasive cleaners.
• Regularly check that there are
no loose screws on this unit and
retighten when necessary.
Parts of your product are produced
from solid pine which is a natural
product containing a beautiful
wooden structure.
Direct sunlight can speed up the
natural process of the resin
contained in the pine knots to change
colour around knots.
This is a normal process happening
to natural wood and cannot be seen
as a manufacturers fault. All wood
has been dryed to Industry standards
for furniture timber and all
procedures for obtaining the best
lacquring finish have been followed.
Our furniture will endure most
temperatures in the home but it is best
to avoid placing furniture next to heat
sources as radiators or fire. Be
particularly careful with solid wood as
the lack of humidity caused by central
heating can cause damage such as
warping.
Safety when using your bed
Do not allow children to climb over the safety rails. Always use the ladder when climbing in and out of bed. Never
attempt to hang bags, bunting or other items with strings or handles on the bed.
2
IMPORTANT, READ CAREFULLY - RETAIN FOR FUTURE REFERENCE
15
,
25 cm

Components - Fittings
Please check you have all the fittings listed below
Note:The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A
Tools reqiured
1cm 2 345678910 11 12 13 14 15 16
1 inch 23456
Rulers - Use this ruler to help correctly identify the screws
Philips screwdriver (medium)
Flathead screwdriver (medium)
Allen key (incl)
Small hammer
Dowel Ø8x40 x34 Conformat screw Ø7x 60mm x20 Screw 3.5 x 35mm x60
Barrel nut Ø10 x 14mm x24 Allen key 4mm x1 Cover cap Ø15/Ø18 x12
Cover cap Ø8/Ø13 x16
E F
H K L
N P
Spacer 20x72x3mm x2
3
Rubber hammer
Q
Connecting bolt M6 x 50mm x5
Connecting bolt M6 x 75mm x19
R
Metal dowel x16
S
Locking nut x32
T
Cover cap Ø4/Ø17 x12
U
Cover cap Ø10/Ø13 x6
V
Cover cap Ø12/Ø3 x20
Y
Rubber hammer
Rubber hammer
3,5x40 Screw x 52
D35 Cover Cap x 8
D4x13 Cover Cap x 20
4,2x35 Screw x 8
7x50mm Screw x 20
55mm Screw x 6
M6x10x13 Cross dowel x 8
D35 Sector x 8
7x60mm Screw x 8
6,3x70mm Screw x 3
M6x75 Bolt x 8
10x40 Wooden dowel x 71
D15x18 Cover Cap x 4
4mm Allen key x 1
D15 Cover Cap x 11
D8x13 Cover Cap x 32 D10x15 Cover Cap x 32
15x80 Wooden Dowel x 4
A
B
C
D
EF
G
H
H
J
H
K
H
LH
M
H
P
H
RH
S
H
T
H
U
3

Components - Panels
3OHDVH FKHFN \RX KDYH DOO WKH SDQHOV OLVWHG EHORZ
8
1
1
4
3
11
6
10 29
5
7
5
514
7
5
12
13
12
10
26
14
9
11 11
8
4

Components - Panels
3OHDVH FKHFN \RX KDYH DOO WKH SDQHOV OLVWHG EHORZ
2Rear Bed rail x 2
(200,6x14,5x2 cm)
10
(89,2x9x3,8 cm)
Slats x2
14
Leg x 2
(123,8x9x2 cm)
Ladder side x2
12
1Front Bed rail x 2
(200,6x14,5x2 cm)
11
(89,2x9x3,8 cm)
Leg x 2
(80,2x48x2 cm)
End panel x 2
7
(72x9x3,8 cm)
Leg x 2
9
(72x9x3,8 cm)
Leg x 2
8
(200,6x14,5x2 cm)
Rear safety rail x 1
3(163,6x14,5x2 cm)
Front safety rail x 1
4
13 Step x 5
(36x6,8x2,5 cm)
5End rail x 4
(80,2x14,5x2 cm)
6End rail x 2
(80,2x14,5x2 cm)
5

4
Assembly Instructions
Step 1
Fitting dowels
Insert wooden dowels A
into the holes in bed rails
1, headboard rails 2
,3, footboard 6and
bottomrail 7.
Note: It may be
nessesary to tap the
dowel in very gently with
small hammer.
Insert wooden dowels
Hinto the holes in
headboard panels 4
and 5.
Note: It may be
nessesary to tap the
dowel in very gently with
small hammer.
Assembling
headboard
Position details and
attach headboard panels
WRKHDGERDUGUDLOVOLNH
showed on illustration at
side.
Step 2
A
AA
A
A
H
A
A
A
A
A
A
11
2
6
7
A
H
H
H
3
4
5
2
5
3 4
4
4
4
4
4
x 6
4
B
35 mm
Step 2
In this step use this fitting:
In this step use this fitting:
A
A
B
B
BB
C
11 C
10
C
8
C
9
C
7
C
6
C
5
C
4
C
3
C
2
C
1
A
A
A
A
A
A
A
A
A
A
A
B
A
A
Insert dowels into the
holes in bed rails, end rails
and safety rails.
Note: It may be necessary
to tap dowel in very gently
with small hammer.
Screw connecting screws
into holes of legs using 4mm
Allen key.
x2
x3
x71
x8
x2
x2 x2 x2
x2
x3
x3 x3
x3
x3
x3
x2 x2
x4
x2
x3
6

4
Assembly Instructions
Step 1
Fitting dowels
Insert wooden dowels A
into the holes in bed rails
1, headboard rails 2
,3, footboard 6and
bottomrail 7.
Note: It may be
nessesary to tap the
dowel in very gently with
small hammer.
Insert wooden dowels
Hinto the holes in
headboard panels 4
and 5.
Note: It may be
nessesary to tap the
dowel in very gently with
small hammer.
Assembling
headboard
Position details and
attach headboard panels
WRKHDGERDUGUDLOVOLNH
showed on illustration at
side.
Step 2
A
AA
A
A
H
A
A
A
A
A
A
11
2
6
7
A
H
H
H
3
4
5
2
5
3 4
4
4
4
4
4
x 6
4
Step 3
Step 4
In this step use this fitting:
In this step use this fitting:
H
U
H
U
H
U
C
C
C
C
H
U
C
6
C
5
C
7
C
5
C
8
C
9
C
10
C
11
H
U
C
H
U
C
C
C
H
U
C
C
H
U
H
U
H
U
Position legs. Insert sectors
into 35mm holes on
end panel 7 as shown in the
picture.
Tighten screws with 4mm
Allen key.
Cover 35mm holes with
cover caps
x4
x4
x4
x4
Position legs. Insert sectors
into 35mm holes on
end rail 6 as shown in the
picture.
Tighten screws with 4mm
Allen key.
Cover 35mm holes with
cover caps
x2
x2
7

4
Assembly Instructions
Step 1
Fitting dowels
Insert wooden dowels A
into the holes in bed rails
1, headboard rails 2
,3, footboard 6and
bottomrail 7.
Note: It may be
nessesary to tap the
dowel in very gently with
small hammer.
Insert wooden dowels
Hinto the holes in
headboard panels 4
and 5.
Note: It may be
nessesary to tap the
dowel in very gently with
small hammer.
Assembling
headboard
Position details and
attach headboard panels
WRKHDGERDUGUDLOVOLNH
showed on illustration at
side.
Step 2
A
AA
A
A
H
A
A
A
A
A
A
11
2
6
7
A
H
H
H
3
4
5
2
5
3 4
4
4
4
4
4
x 6
4
POSITION 1 POSITION 2
Step 5
Step 6
In this step use this fitting:
In this step use this fitting:
E
EE
D
D
D
D
D
D
E
E
E
D
D
F
F
F
D
D
D
E
E
E
C
3
C
1
C
2
C
1
C
2
E
E
D
F
E
D
E
D
F
E
D
Push Cross dowel into
hole in bed rails 1 and 2
the groove on Cross dowel
should be horizontal.
Push Bolt through each
leg to meet Cross dowel
and then fasten with the
Allen key.
Push Cross dowel into
hole in bed rail 1 and 2
the groove on Cross dowel
should be horizontal.
Push Bolt through each
leg to meet Cross dowel
and then fasten with the
Allen key.
Attach the rear safety rail 3
to the legs with the screws
Tighten with Allen key
x4
x4
x2
x4
x4
(using under bed
Storage Unit) (using Truckle/drawer)
8

4
Assembly Instructions
Step 1
Fitting dowels
Insert wooden dowels A
into the holes in bed rails
1, headboard rails 2
,3, footboard 6and
bottomrail 7.
Note: It may be
nessesary to tap the
dowel in very gently with
small hammer.
Insert wooden dowels
Hinto the holes in
headboard panels 4
and 5.
Note: It may be
nessesary to tap the
dowel in very gently with
small hammer.
Assembling
headboard
Position details and
attach headboard panels
WRKHDGERDUGUDLOVOLNH
showed on illustration at
side.
Step 2
A
AA
A
A
H
A
A
A
A
A
A
11
2
6
7
A
H
H
H
3
4
5
2
5
3 4
4
4
4
4
4
x 6
4
Step 7
In this step use this fitting:
Step 8
In this step use this fitting:
H
H
H
H
H
H
J
H
J
H
J
H
J
H
J
H
J
G
G
H
M
H
M
C
12
C
12
C
13
C
13
C
13
C
13

H
H
J
H
M
G
H
H
J
Always placed inside the ladder
Insert Dowels into the
holes in lower bunk legs.
Place upper bunk on lower
bunk as shown on
illustration.
Fix dowels in legs with
screws using Philips
screwdriver.
Assemble ladder sides 12
and steps 13 as shown in
the picture.
Use connecting screws
and 4mm Allen key.
Cover the heads of the
connection screws with
cover caps
x4
x8
x16
x16
Follow this step if you
are assembling bed in
position 2


4
Assembly Instructions
Step 1
Fitting dowels
Insert wooden dowels A
into the holes in bed rails
1, headboard rails 2
,3, footboard 6and
bottomrail 7.
Note: It may be
nessesary to tap the
dowel in very gently with
small hammer.
Insert wooden dowels
Hinto the holes in
headboard panels 4
and 5.
Note: It may be
nessesary to tap the
dowel in very gently with
small hammer.
Assembling
headboard
Position details and
attach headboard panels
WRKHDGERDUGUDLOVOLNH
showed on illustration at
side.
Step 2
A
AA
A
A
H
A
A
A
A
A
A
11
2
6
7
A
H
H
H
3
4
5
2
5
3 4
4
4
4
4
4
x 6
4
Choose this position if adding Under bed Storage Unit
Step 9
In this step use this fitting:
Step 10
In this step use this fitting:
H
M
G
H
K
H
K
F
H
K
H
K
H
K
C
4
C
13
C
12
C
12
C
13
C
13
C
13
C
13
F
H
K
F
H
K
H
K
H
M
G
G
H
M
Place the ladder as shown on
the side of the bed you
decided (left or right).
Connect ladder to Front bed
rail using screws and a
4mm Allen key.
Fix safety rail 4 to ladder with
screws and with screw
to leg.
Assemble ladder sides 12
and steps 13 as shown in
the picture.
Use connecting screws
and 4mm Allen key.
Cover the heads of the
connection screws with
cover caps
x20
x20
x6
x1
Now you must decide if the
ladder is placed in the left or
the right side.
Follow this step if you are
assembling bed in position 1
10

4
Assembly Instructions
Step 1
Fitting dowels
Insert wooden dowels A
into the holes in bed rails
1, headboard rails 2
,3, footboard 6and
bottomrail 7.
Note: It may be
nessesary to tap the
dowel in very gently with
small hammer.
Insert wooden dowels
Hinto the holes in
headboard panels 4
and 5.
Note: It may be
nessesary to tap the
dowel in very gently with
small hammer.
Assembling
headboard
Position details and
attach headboard panels
WRKHDGERDUGUDLOVOLNH
showed on illustration at
side.
Step 2
A
AA
A
A
H
A
A
A
A
A
A
11
2
6
7
A
H
H
H
3
4
5
2
5
3 4
4
4
4
4
4
x 6
4
POSITION 1 POSITION 2
Step 11
In this step use this fitting:
Step 12
In this step use this fitting:
H
T
H
T
H
P
H
P
H
P
H
P
H
R
H
R
H
L
H
L
H
L
C
14
C
14
H
P
H
P
H
P
H
P
H
T
H
T
H
T
H
T
H
T
H
T
H
T
H
T
H
PH
P
H
R
H
R
H
R
H
P
H
P
H
R
H
R
H
P
H
T
H
L
H
L
H
P
H
P
Position slats equally.
End slats must be in contact
with legs.
Place two screws in each
slat and tighten using a
Philips screwdriver.
Cover the heads of screws
and bolts with cover caps.
Cover all unused holes with
cover caps as shown.
x26
x29
x11
x52
x52
x2
x5
x5
x2
x2
x2
x2
x2
11

4
Assembly Instructions
Step 1
Fitting dowels
Insert wooden dowels A
into the holes in bed rails
1, headboard rails 2
,3, footboard 6and
bottomrail 7.
Note: It may be
nessesary to tap the
dowel in very gently with
small hammer.
Insert wooden dowels
Hinto the holes in
headboard panels 4
and 5.
Note: It may be
nessesary to tap the
dowel in very gently with
small hammer.
Assembling
headboard
Position details and
attach headboard panels
WRKHDGERDUGUDLOVOLNH
showed on illustration at
side.
Step 2
A
AA
A
A
H
A
A
A
A
A
A
11
2
6
7
A
H
H
H
3
4
5
2
5
3 4
4
4
4
4
4
x 6
4
Step 13
In this step use this fitting:
Step 14
In this step use this fitting:
C
6
C
6
H
S
H
S
H
S
H
S
H
S
C
H
U
C
H
U
C
H
U
C
H
U
C
H
U
B
B
Detaching the Bunkbed into 2
separate beds.
Turn end rail 6 in upper bunk
ends by taking cover cap
off and releasing fitting
and
Retighten fitting and
and push cover cap back
on.
Assemble separate beds as
shown.
Use upper bunk endpanels
as headboard and lower bunk
endpanels as footboard.
Cover all unused holes with
cover caps as shown.
x4
12

13

Customer Service Form
Please return complete to Fax: [phone]
Name:
Address:
Contact No:
Date of purchase:
Place of purchase:
Product Name:
See assembly instructions:
Problem:
Parts Needed: Part No. Quantity
Please quote assembly
instruction or number
Description
e.g drawer base
14