Stonepoint Ll-100-25d User manual

LED Low Voltage Linkable

Landscape Light Kits

w/Dusk to Dawn Transformers

PRODUCT TERMS

ADDITIONAL WARNINGS

INSTALLATION

2 YEAR LIMITED WARRANTY

ALSO COMPATIBLE WITH THIS SET:

This product is guaranteed against failure due to factory defects in materials or workmanship for two (2) years from the date of purchase. This

warranty is non-transferable and applies only to the original owner. Proof of purchase is required for repair or replacement. This warranty

does not cover normal wear of parts or damage resulting from any misuse of the product. Misuse of the product includes, but is not limited to:

washing the product, using in extreme weather conditions, opening the product, or trying to remodel the product. Important: this warranty is

only valid if the product has been purchased through an authorized reseller. Returns and/or warranty replacements must be processed at the

original place of purchase.

WARNINGS

SAFETY AND PRECAUTIONS

CUSTOMER SERVICE

For questions regarding this product, please e-mail us at [email protected].

TROUBLESHOOTING GUIDE

CLEANING INSTRUCTIONS

Using a soft cloth, clean the fixture using a mild, non-abrasive glass cleaner. DO NOT use solvents. DO NOT use cleaners containing

abrasive agents. NEVER spray liquid cleaner directly onto the light or LED.

Problem Probable Cause

Solution

Light comes on during the

daylight hours.

Light cycles ON and OFF

continuously (strobe light effect).

1. Dusk-to-dawn sensor is

detecting reflected light

from the landscape light.

1. Change the position of the light head.

Reposition light away from the reflecting surface.

2. Place a small piece of black electrical tape over

the bottom half of the dusk-to-dawn sensor.

3. Move the light to a different location where the

results are better.

1. Fixture is located in a shaded

area; dusk-to-dawn sensor is

detecting darkness.

1. Shine a light at the dusk-to-dawn sensor.

If the landscape light immediately shuts off,

then the fixture is located in an area that is

too dark to allow enough light to enter the

sensor. The light will need to be relocated.

Circuit breaker trips or fuse blows

when light is turned on.

1. Discontinue use

immediately.

1. Call an electrician.

Individual light goes out. 1. Loose connection.

2. Damaged light or cord.

1. Check connection.

2. Discontinue use immediately.

3 4

Light Head Light Head

SPOT LIGHT PATHWAY LIGHT DUSK TO DAWN

TRANSFORMERS

DUSK TO DAWN

TRANSFORMER

w/ 4-8-D2D TIMER

DUSK TO DAWN

TRANSFORMER

without TIMER

Cord

Notch

Cord

Quick

Connector

Wood Screw

Plug

Quick

Connector

Shroud

Diffuser

Cap

Tube

Collar Ring

Friction

Lock

Ground Stake

Ground

Stake

Thumbscrew

Dusk-to-Dawn

Sensor

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes

or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet

on a circuit different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.

2. Each connection is made up of a connector

(Fig. 3)

and a

quick connector

(Fig. 4). The quick connectors and

connectors are only designed to connect one way.

Remove the thumbscrew from the stake (Fig. 1). Line up the flat side of the ground stake with the friction lock (Fig. 2) against the friction lock on the

back of the light head (Fig. 3). Fasten both pieces together with the thumb screw (Fig. 4).

Refer to the PAGE 5 for the maximum number of light kits that can be added to each model of landscape light kits. The total combined watts of

each light on the set must not exceed the maximum wattage rating of the dusk to dawn transformer.

Attach the light heads to the main cord, depending on the kit. There are 4-5 connectors spaced along the length of the main cord. Plug in the quick

connectors from the light heads into the connectors in the main cord (Fig. 8). Fully insert the quick connectors into the connectors (Fig. 9). Tighten the

collar ring firmly to keep water out (Fig. 10).

An end cap must be securely attached at the end of the main cord to guard against water

(Fig.

11)

(The dusk to dawn transformer is ready to be plugged in).

WARNING: DO NOT use with extension cords near water or

wherever water may accumulate.

WARNING: ONLY use in a GFCI protected outlet for outdoor utilizations.

(Fig. 1)

(Fig. 2) (Fig. 3)

(Fig. 4)

(Fig. 8) (Fig. 9)

(Fig. 10) (Fig. 11)

SPOT LIGHT ASSEMBLY & OPERATION

INSTALLING ADDITIONAL UNITS

Push stakes into ground and aim light.

Check all connections, make sure they are all on tight to prevent water from entering the connections

These fully compatible add-on/replacement lights are sold separately. If adding these lights to an existing set, please verify they

will not exceed the maximum watttage rating of the dusk to dawn transformer.

(Fig. 5) (Fig. 6) (Fig. 7)

Attach the main cord to the

dusk to dawn timer (

Fig. 5). Fully insert the connector into the quick connector (Fig. 6). Tighten the collar ring firmly to keep

water out (Fig. 7). Unroll the cord and connect the light heads and place in desired location.

Quick Connector

Connector

WARNING: Do NOT look directly at LED light sources.

WARNING: Avoid using this product in the immediate

vicinity of highly flammable materials, liquids and gases.

WARNING: DO NOT alter or disassemble any of the parts of this fixture. It is

completely enclosed and does not contain replaceable or serviceable parts.

12W and 24W DUSK TO DAWN TRANSFORMER

with 3 TIME SETTINGS:

The lights will automatically turn on at dusk. The adjustable timer is

located on the side of the transformer, this will determine how long the

lights stay on. Set the switch to either 4H (on at dusk off 4 hours

later), 8H (on at dusk off 8 hours later) and DUSK TO DAWN (turns

the lights on at dusk and off at dawn).

12W DUSK TO DAWN TRANSFORMER:

This unit plugs in directly over an electrical outlet. The lights will

automatically turn on at dusk and off at dawn.

DUSK TO DAWN TRANSFORMER CONTROL

Revision Date: 10-28-2019

MATERIAL: Plastic

CORD LENGTH: 25 ft.

NUMBER OF HEADS: 3

LUMENS PER HEAD: 100 (300 total lumens)

WATTS PER HEAD: 1.5 (4.5 total watts)

TRANSFORMER: 12 Watts MAX., Dusk to Dawn

LINK UP TO A MAXIMUM OF 12 WATTS

25 FT

MATERIAL: Plastic

CORD LENGTH: 40 ft.

NUMBER OF HEADS: 4

LUMENS PER HEAD: 35 (140 total lumens)

WATTS PER HEAD: 0.5 (2 total watts)

TRANSFORMER: 12 Watts MAX., Dusk to Dawn

w/ timer settings (4 Hour or 8 Hour)

LINK UP TO A MAXIMUM OF 12 WATTS

30 FT

MATERIAL: Metal

CORD LENGTH: 30 ft.

NUMBER OF HEADS: 3

LUMENS PER HEAD: 200 (600 total lumens)

WATTS PER HEAD: 3 (9 total watts)

TRANSFORMER: 24 Watts MAX., Dusk to Dawn

w/ timer settings (4 Hour or 8 Hour)

LINK UP TO A MAXIMUM OF 24 WATTS

MATERIAL: Metal

CORD LENGTH: 40 ft.

NUMBER OF HEADS: 4

LUMENS PER HEAD: 75 (300 total lumens)

WATTS PER HEAD: 1.2 (4.8 total watts)

TRANSFORMER: 24 Watts MAX., Dusk to Dawn

w/ timer settings (4 Hour or 8 Hour)

LINK UP TO A MAXIMUM OF 24 WATTS

1. Suitable for outdoor use.

2. Do NOT look directly at LED light sources.

3. The LED modules used in this fixture are not serviceable.

4. This product is inspected prior to shipping. Do not use if

product is cracked, broken or missing parts.

5. Suitable for use in operating environments ranging between

-13° to 122°F (-25° to 50° C). Lifetime of this product may be

reduced with prolonged exposure to extreme temperatures.

6. Do not anchor cord with staples, nails, or similar objects to

avoid puncture and damage to the cord.

7. Do not cover this product as the covering may cause the

lights to overheat or ignite.

8. Modifications or hardwiring of product voids the warranty.

WARNING: This product has a polarized plug (one contact blade is wider than the

other) as a feature to reduce the risk of electric shock. The plug is fashioned to only fit in

a standard outlet one way. If it does not fit, flip the plug and try again. If it still does not fit,

contact a qualified electrician. DO NOT ALTER THE PLUG OR CORD. WARNING: Only use this product with an extension cord for

outdoor use with the following extension cord types: SEW,

SOEW, SOEOW SOW, SOOW, STW, STOW, STOOW, SJEW,

SJEOOW, SJW, SJOW, SJOOW, SJTW, OR SJTOOW.

9. Do not use if there is any damage to the light or cord

insulation. Inspect periodically.

10. Do not install the lighting near flammable liquids.

11. Do not install cord on doors or gates where repeated flexing

can occur.

12. For outdoor installation, a Ground Fault Interrupting Circuit

(GFCI) outlet must be used.

13. Do not hang objects from cords.

14. Do not use with dimmers or in-line cord switches.

15. Do not allow the light head to touch the ground.

16. Ensure all connections and the cap on the last segment of

cord is tightly secured to prevent water entry.

17. Unplug cord from outlet prior to adding additional strands.

1. The dusk to dawn timer

should be plugged into a

GFCI protected outlet after the

installation is complete. There

are 2 basic styles of dusk to

dawn transformers included in

the landscape lighting kits: 1.

The dusk to dawn transformer

in the kit directly plugs into and

covers the outlet (Fig 1). 2. If

the set includes a dusk to

dawn transformer that surface

mounts, attach it to a surface

using the included wood

screws. (Fig. 2).

1.Place the pathway light tube over

the stake (Fig. 1). A notch is located on the bottom edge of the tube where the cord will need to be carefully guided

through as the stake and tube are connected together (Fig. 2). The pathway light is now ready to be pushed into the ground (Fig. 3).

PATHWAY LIGHT ASSEMBLY

4H 8H DUSK TO DAWN

40 FT

Push stakes into ground and aim light. The light heads can be positioned from horizontal to straight up (Fig. 5). Loosen the thumbscrew to adjust the light

head to better aim the light where desired. Once that is achieved, tighten the thumbscrew.

Modifications or hardwiring of product voids the warranty!

This fixture is rated for outdoor use.

4-8-D2D Switch

Mounting Tabs

LVPPD-35-BOL

0.5 Watts

LVPPP-35

0.5 Watts

LVPMD-75

1.2 Watts

WL-200

3.5 Watts

LVSPD-100

1.5 Watts

LVSMD-200

3 Watts

LVSMD-400

5.5 Watts

25 ft. 3 Light, Dusk to Dawn Kit

MODEL No: LL-100-25D

30 ft. 3 Light, Dusk to Dawn Kit

MODEL No: K3LVSM-30

40 ft. 4 Light, Dusk to Dawn Kit

MODEL No: K4LVPPP-40

40 ft. 4 Light, Dusk to Dawn Kit

MODEL No: K4LVPM-40-75

100 Lumen Plastic

Landscape Lights w/ 3 ft. cords

Operating Voltage: 12-24V

(24V Max.)

12W Plug-in

Dusk to Dawn

Transformer

Operating voltage: 110-240v

24W Plug-in Dusk

To Dawn Transformer

w/ 4 or 8 Hour

Time On Settings

Operating voltage:

110-240v

25 ft. 18/2 SPT-2W

Main Cord

40 ft. 18/2 SPT-2W

Main Cord

40 ft. 18/2 SPT-2W

Main Cord

Weatherproof

Caps

Weatherproof

Caps

Weatherproof

Caps

Weatherproof

Caps

30 ft. 18/2 SPT-2W

Main Cord

200 Lumen Metal

Landscape Lights w/ 3 ft. cords

Operating Voltage: 12-24V

(24V Max.)

35 Lumen Plastic Pathway

Lights w/ 3 ft. cords

Operating Voltage: 12-24V

(24V Max.)

75 Lumen Metal Pathway

Lights w/ 3 ft. cords

Operating Voltage: 12-24V

(24V Max.)

12W Plug-in Dusk to Dawn

Transformer w/ 4 or 8 Hour

Time On Settings

Operating voltage: 110-240v

24W Plug-in Dusk To

DawTransformer

w/ 4 or 8 Hour

Time On Settings

Operating voltage:

110-240v

Fig. 1 Fig. 2 Fig. 3 Fig. 4

MODEL No: LL-100-25D

25 ft. 3 Plastic Spot Light Kit with a Dusk to Dawn Transformer

MODEL No: K4LVPPP-40

40 ft. 4 Plastic Pathway Light Kit Featuring a Dusk to Dawn Transformer with 2 Time On Settings

MODEL No: K3LVSM-30

30 ft. 3 Metal Spot Light Kit Featuring a Dusk to Dawn Transformer with 2 Time On Settings

MODEL No: K4LVPM-40-75

40 ft. 4 Metal Pathway Light Kit Featuring a Dusk to Dawn Transformer with 2 Time On Settings

Fig. 5

Fig. 1 Fig. 2 Fig. 3