NANGUANG CN-1200DCHS User manual

1.After receiving the light ,please check if any damage caused by transportation. If there is damage caused by
transportation ,please do not use the light and contact with the distributor or the manufacturer ASAP.
2.Please do not mount the light directly on the surface of the common combustible material. Keep the light dry
and keep it away from wet ,hot or dusty condition ,prevent the light from water or other liquids.
3.Before installation ,please make sure the power voltage you use should be according to the voltage indicated
on the lamp ,please do not open and repair the lamp yourself when the power is on.
4.Please do not use the power cord which is with bad insulating layer, and do not pull the plug or drag the power
cord directly.
DMX IN DMX OUT
The connection between light and light,or between light and the controller should use 3 pins power
cord which the diameter is not less than 0.5mm.Please use 3 pins XLR plug to connect the DMX 512
output / input. The connection between XLR plug and the cable is showed as above photo.
Use the XLR cable from the DMX output socket of the controller to connect with the DMX input socket
of the first light, and from the DMX output of the first lamp to connect with the DMX input of the second
lamp, and so on, until finish the connection of all lights.
·Notice: the length of the XLR control cable can't be longer than 300m.
CN-1200DCHS Studio LED Light
Instruction Sheet
The lighting comes with accessoiries together,pls check carefully.
Name
XLR Signal line
Instruction sheet
Power Adapter
Filter set
Power cable
Quantity
1
Unit
PC
Remarks
English
15V
Parameters:
LED Bulbs Amount:1200 pcs Total Power:72W
AC Power:100V-240V DC Power:15V
Color Temperature:7500K-3200K
4.Channel instruction
When the LED light is mono color,the address choose 001, it will occupy the corresponding pusher
CH1 in DMX controller.
When the LED light is Bi-color,the address choose 001,and the system will occupy the corresponding
pusher CH1,CH2 in DMX controller.After choose and confirm the address,
next time it will remain the previous address as a default one.
Safety Warning:
control signal connection
General Breakdown Service
Description of Breakdown Measurements
The lamp can not start up normally
The manual function is right but can not
controlled by the controller
The screen can not display or the content disorder
The light is on but can not be operated by
manual or controller
1.Please check if the power cord is connected firmly
2.The plug of the power supply is connected well with
the lamp or not
1.Check the setting of the DMX starting address is correct or not
2.Check if the XCR signal wire damaged or not.
Turn off the power for 1 minute and restart.
Internal CPU chip damaged,please contact with the
supplier or return it back to factory.
GND 1
DATA- 2
DATA+ 3
1 GND
2 DATA-
3 DATA+
1PC
1PC
1SET
1PC
www.nglbg.com
Add:Zhanglin Section,Highway324,Dongli,Chenghai,Shantou City,Guangdong Province,China
Tel:[phone] Fax:[phone]
E-mail:[e-mail] http://www.nglbg.com
Please switch off
the power button
before inserting
or removing the
power cable.
Guangdong NanGuang Photo&Video Systems Co.,Ltd

Please switch off
the power button
before inserting
or removing the
power cable.
1) .In 3 seconds after starting up ,the language select option appear ,press or
to choose Chinese or English ,and press to get into model display page.
2) .The Model No. stays for 3 seconds or you can press directly to enter main menu,
press or button to choose each menu setting ,the menu show as below :
1 . DMX512
2 . Manual
·When choose 1 .DMX512 option and press to get into the setting page for DMX512
address. Show as below: 1 . DMX512 address:XXX
2 . Bi-color temperature
When choose 1.DMX512 address :XXX and press to get into settings,press or
to choose DMX channel address .Press to confirm and press to return to the
previous page.
When choose 2.Bi-color temperature and press to read the data of adjustable brightness
XXX%: it will show ch1.TC-5600K:XXX %, ch2.TC-3200K:XXX%,
press to return to the previous page.
·When choose 2 .Manually and press to manual display page.
When the screen shows (Bi-color temperature),press ,the screen will show :
ch1.TC-5600K :XXX% ch2. TC-3200K:XXX%
And press to manual dimming condition,press or to adjust LED light brightness.
If need to switch function,press to backspace,and oprerate as above.
Please switch off
the power button
before inserting
or removing the
power cable.
1. Mount the lighting on a light stand with a suitable direction, unfold the
barn doors . Please check if the power is off,then connect the DC power,
turn on the power and use.
2. Please insert diffuser or filter from the right side(as picture on the right).
3.Operating instructions
Instructions:
Components:
Barn Doors: For better adjustment of light direction.
Display screen: Show the function operate data.
Clamping Screws: To fix the light panel with U-bracket.
U-bracket: To fix the light panel and adjust light direction.
Power Switch: To switch on or off.
Power Input Socket: For input of AC/DC power.
DMX input socket: For input DMX signal.
DMX output socket: For output DMX signal.
Power Adapter: For connecting 230V-110V AC power to DC inverting and power stabilizing.
XLR connect cable: Connect DMX Signals between LED lightings, and between LED lightings
and lighting console.
Sony V-Lock Battery Plate:For mounting Sony V-Lock Batteries.
Diffuser and Filters:Without diffuser and filters,light is of spotlight effect and suitable for
shooting at a relatively long distance;with diffuser,light is of soft light effect;with extra soft
diffuser,light is of extra soft light effect; With blue filter,color temperature could be adjusted
towards 7500K (As below pictures).
LED Light panel
Display screen
DMX Input Socket
DMX Output Socket
U-Bracket
Barn doors
Power Input Socket
Power Switch
Clamping Screws
Power Adapter
XLR Cable
1
2
3
4
5
6
7
8
9
11
10
1
2
3
4
5
6
7
8
11
9
10
12
Sony V-lock Battery
Plate
Without filter and
diffuser
With diffuser With blue filter