Monster MLB7-1030 User manual

BLUETOOTH®
MULTI-COLOR LED LIGHT BAR
MODEL MLB7-1030
V1.0 0819
Operation Manual

Features
What’s Included
Introduction
• Multi-color and dimmable LED lighting effects
• Included color-selector remote with positionable IR receiver
• Bluetooth®app controlled
• Multi-position base for various horizontal, vertical,
or wall mounting orientations
• Conveniently plugs into any 5V USB power source (not included)
• Plug and play
• Control multiple light bars simultaneously through the app
This Bluetooth® Multi-color LED Light Bar is easy to install,
easy to use, and is ideal for adding controllable ambient
lighting to any room.
• Bluetooth® Multi-color LED Light Bar
• IR Remote Control
• Multi-position Base
• Base Attachment Screws x2
• Base and IR Receiver Adhesive
• User Manual x1 pc

• Keep these instructions.
• Do not drop, puncture, or disassemble this product.
• Avoid long exposure to direct sunlight, which may cause
damage.
• Do not expose this product to dripping or splashing of drinks
or liquids of any kind.
• Do not expose this product to open flames.
• Do not use the product in a strong magnetic field.
• Use a clean, soft cloth to clean. Do not use any corrosive
cleaners/oils to clean.
• Do not attempt to repair the device or open the unit as this
will void the warranty.
Please read and understand all instructions before using this
product. If damage is caused by failure to follow the
instructions, this warranty is null and void.
Safety
Instructions
Specifications
• LED Light Bar (USB): 5V
• output: 1.5W
• cable length: 5ft
• remote control: 3V
(1 x 3V battery, type CR2025)

WALL MOUNT
HORIZONTAL
VERTICAL
Get Started
1Determine where and in what orientation you would like
to use your Bluetooth®Multi-color LED Light Bar
2Pass the USB power cord and
IR receiver through the opening
in the multi-position base

5Remove the tab from the battery compartment of the
remote control
6Connect the USB cable to a powered USB port or
wall charger (1A adapter required – not included)
3For horizontal or wall mounted orientations, attach the base
in the center of the light bar using the two included screws.
For vertical orientation, route cord through the cord channel
and attach the base at the end of the light bar.
4Position the IR receiver in a location where it can receive
signal from the IR remote. Secure the receiver using the
included adhesive tape if desired.
screws
horizontal or
wall mounted:
to avoid cord damage,
don’t pull the cord tight
vertical:
using the cord channel
makes the vertical
light bar more stable
adhesive
this
side
UP
wall mounted tip:
attach the base to the wall
first using the adhesive tape
or, if desired, a screw and
anchor (not included)

①
②
③
④
⑤
⑥
⑦
⑧
Controls, at a Glance
ON/OFF
MULTI-WHITE SELECTORS
MULTI-COLOR SELECTORS
FLASH
STROBE
FADE
SMOOTH
RESET
DIMMER BUTTONS
⑥
Turn the product on and off
Select from cool, soft, or warm white
Change the color to match your mood
Flash color-changing mode
Strobe color-changing mode
Fade color-changing mode
Smooth color-changing mode
Reset to default settings
Adjust the brightness/intensity
④ ⑤ ⑥ ⑦
⑧
⑥
①
②
③
IR Remote IR Receiver (in-line)

IR Remote
Operation
1
2
Turn on the LED Light Bar by pushing the ON button
on the remote control
3Set the desired brightness using the buttons to
increase/decrease the intensity of color
Select the desired color of the desired effect by pushing
the corresponding button on the remote control
4Push the OFF button to turn off the LED Light
1
2
The battery compartment is located on the narrow side
of the remote control
3Place the battery compartment back in the remote control
so it locks in place
Remove the empty battery and insert a 3V battery,
type CR2025, with the positive terminal pointing upwards
Changing the remote control battery:
Note: The battery for the remote control has already been
installed. Remove the battery pull tab to operate.

Bluetooth®
App Operation
1
2
Download the free Monster Basics Light Control app
3Once connected, you can now control color, brightness,
color-changing modes and speeds, music reactive, and
on/off scheduling
NOTE: Your LED Light Bar must be connected to power and your
phone must be Bluetooth enabled and within range to operate
Enable Bluetooth®connectivity on your device. Open the
Monster Basics Light Control app and locate your Monster
LED Light Bar in the equipment section. Select the device
in the list to connect.
ON/OFF
COLOR SPECTRUM WHEEL
BRIGHTNESS ADJUST
COLOR SELECT
SPEED ADJUST
COLOR-CHANGING MODES
MENU ITEMS
Color Control:

Customer
Service
1 Year Limited Warranty
866-246-2008
Notice
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation
is subject to following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Warning
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
warranty or authority to operate the equipment.