Strahman HYDRO-PRO 150 User manual

RENEWABLE COVER REPLACEMENT
If the renewable cover (2) becomes worn or cracked, follow the steps below
to replace it.
1. Disassemble the renewable cover (2) by loosening and removing the six cover screws (4) (not shown).
2. Lift the body (1) free of the cover (2). Remove the ratchet assembly hinge (3), ratchet (5), and ratchet
spring pin (13).
3. lnstall the body (1) and ratchet assembly-hinge (3) ratchet (5), ratchet spring (13) and spring pin (14) in the
new renewable cover (2). Reinstall the six cover screws (4) (not shown).
RUBBER COVER - BLACK RUBBER COVER - RED RUBBER COVER - WHITE Assembly Instructions
HYDRO-PRO 150®
WATER-SAVER SPRAY NOZZLE
WDEHP150062020
A
C
E
R
T
I
F
I
E
D
Q
U
A
L
I
T
Y
P
R
O
D
U
C
T
•
A
C
E
R
T
I
F
I
E
D
Q
U
A
L
I
T
Y
P
R
O
D
U
C
T
•
A
C
E
R
T
I
F
I
E
D
Q
U
A
L
I
T
Y
P
R
O
D
U
C
T
•
1 YEAR
LIMITED
WARRANTY
ESTABLISHED 1921
STRAHMANVALVES.COM
WORLD HEADQUARTERS
STRAHMAN VALVES, INC.
2801 BAGLYOS CIRCLE, BETHLEHEM, PA 18020
P: +1 484.893.5080 F: +1 484.893.5099 E: [email protected]
UNITED STATES • FRANCE • GERMANY • CHINA • HONG KONG

HYDRO-PRO 150® WATER SAVER NOZZLE
INSTRUCTIONS FOR SERVICING SPRAY NOZZLE
If the Hydro-Pro 150 begins to leak from the seat (14) or rear of the body (1) follow
the steps below. For best results, order original Strahman parts.
1. Disassemble the renewable cover (2) by loosening and removing the six cover screws (4) (not shown).
2. Lift the body (1) free of the cover (2). Remove the ratchet assembly hinge (3), ratchet (5), and ratchet spring pin (13).
Place the body in boiling water for 2-3 minutes to release the Loc-Tite bond on stem screw (11). Remove the stem
screw (11) and swivel the U-bracket (17) down or up away from the stem (9).
3. Remove the snap rings (7) from the font and rear of the water saver body (1). Push on the rear of the stem (9) until
the seat stem (14) and stem spring (10) are free of the body.
4. Carefully press the housing (8) out of the rear of the water saver body (1). Precautions should be taken to avoid
damaging the inside of the water saver body.
5. lnstall a new “O-ring” (6) on the seat (14). Install a new “O-ring” (6) on the new housing (8).
6. lnstall seat (14) and snap-ring (7) in the front of the water saver body (1). Install the stem (9) and then stem spring
(10) from the rear of the water saver body.
7. Install the housing (8) in the rear of the body and compress the stem spring (10). Install a snap ring (7) in the rear of
the water saver body.
8. Swivel the U-bracket (17) back into place over the end of the stem (9). Apply Loc-Tite 271 to the stem screw (12) and
reinstall.
9. Re-install the body (1) and ratchet assembly-hinge (3) ratchet (5), and ratchet spring pin (13) in the new renewable
cover (2). Reinstall the six cover screws (4) (not shown).
PARTS LIST
ITEM
NO. ORDER NUMBER DESCRIPTION
1 HPBODYASSM HYDRO-PRO 150® BODY
2
WSHP1COVER0007 RENEWABLE COVER - BLACK
WSHP1COVER0008 RENEWABLE COVER - RED
WSHP1COVER0009 RENEWABLE COVER - WHITE
3 HP1HINGESS RATCHET HINGE ASSY, SST
4 HP1SCR COVER SCREWS (SET OF 6) (NOT SHOWN)
5 HP150RACHETASSY RATCHET
6 ORNG18MM02MMEA O-RINGS (SET OF 6)
7 HP1SNAPRINGSS SNAP RETAINING RING, SST
8 HP1HOUSASSY HOUSING, SST
9HP150STEMASSY STEM ASSEMBLY
10 SPRG12339S3SS SPRING STEM (SET OF 6), SST
11 MSN8320038LWOZ STEM SCREW & WASHER (SET OF 6)
12 SPRG12410S5SS RATCHET SPRING, SST
13 HP1SPINSS RATCHET SPRING PIN (SET OF 6) SST
14
HP1SEAT HP 150 SEAT, SST
HP1SEATLFSS HP 150 LOW FLOW SEAT, SST
15 HPILARM9 LEVER ARM
16 WSHP1LPIV0000 LEVER ARM PIVOT ASSY
17 HP1UBRKSS U-BRACKET, SST
3
5
11
10
1
2
15
12
13
6
14
7
17
9
6
7
8
2
16
3
5
11
10
1
2
15
12
13
6
14
7
17
9
6
7
8
2
16
3
5
11
10
1
2
15
12
13
6
14
7
17
9
6
7
8
2
16
3
5
11
10
1
2
15
12
13
6
14
7
17
9
6
7
8
2
16
Add pipe sealant at this connection;
tighten to ensure an adequate seal.