STRAPBINDER POW'R-WRAP TOOL HBPW8201 User manual

POW'R-WRAPTM TOOL
MANUFACTURER PART NUMBER RSA-590
STRAPB
Contents
2 Technical Data
3 Safety Instructions
5 Operation Instructions
6 Adjustment & Maintenance
7 Schematic & Parts List

2
TECHNICAL DATA
Length 7.89”
Width 0.99”
Height 6.38”
Weight 1.17 lbs
Strapping Dimensions
Width ¼”
Thickness .015”
Material Smooth stainless-steel

3
SAFETY INSTRUCTIONS
Read and follow operation instructions carefully.
Failure to follow these warning can result in severe personal injury.
eye injury hazard
When handling RSA-590 and stainless-steel strap, always wear protective glasses.
Failure to wear safety glasses with side shields can result in severe eye injury or blindness.
Always wear safety glasses with side shields that conform to ANSI Standard Z87.1.1
protective gloves
When handling RSA-590 and stainless-steel strap, always wear protective gloves.
strap warnings
Never use strap as a means of pulling or lifting loads.
Follow operation instructions (pg. 5) to properly apply using the RSA-590.
strap breakage hazard
Sudden loss of strap tension or strap breakage can occur due to improper operation of the
RSA-590, excessive tensioning, using non-recommended strapping or sharp corners on a load.
This can further lead to a sudden loss of balance causing one to fall or the tool and strap flying
violently.
Preventatives:
• Use edge protectors if load corners are sharp
• Use recommended strap quality, width, gauge, and tensile strength (page 2)
• Place strap correctly around a properly positioned load
• Load strap correctly into the RSA-590 tool
• When tensioning, position yourself to one side of the strap and keep all bystanders away

4
cutting tensioned strap
When cutting strapping, use the proper strapping cutter and keep other bystanders and yourself
at a safe distance from the strap. Always stand to side of strap, away from the direction in which
the loosened strap will release.
tool hazard
A well maintained and inspected tool can optimize safety!
Check tool daily for broken or warn parts.
DO NOT MODIFY any part of the tool without proper expertise and supervision. Unsupervised
modification can result in severe personal injury.
fall hazard
Keep work area tidy. A cluttered or messy work area may cause a risk of injury.
Maintain proper footing and/or balance – especially in elevated areas – when operating
the RSA-590.
Failure to do so may result in falling and severe personal injury.
Both feet should be securely placed on a flat, solid, surface. Do not use the RSA-590 when
you are in an awkward position. In addition, follow the rules and regulation established in the
workplace to prevent accidents.

5
OPERATION INSTRUCTIONS
RSA-590 works with ¼ smooth stainless steel strapping.
1. Preset desired tension (0-8) by turning the knob at the rear of the tool – the higher the
number, the tighter the tension capacity.
0 = 15 lbs 1 = 20 lbs 2 = 30 lbs 3 = 40 lbs
4 = 50 lbs 5 = 60 lbs 6 = 70 lbs 7 = 75 lbs 8 = 80 lbs
2. Push tension handle forward to open strap grip.
3. Slide the end of the strap through the opening and push the tool forward on the strap until the
clips are holding the seal.
4. Squeeze the tension handle several times, until the tool locks.
Once locked, squeeze the handle one more time to seal and cut the strap.
Result: deep punch and dual lock on the outside
5. When complete, remove remaining strapping from tool by working handle back and forth.
Tension Capacity Indicator
Tension Adjustment Knob
Tension Handle
Strap Grip & Clips

6
ADJUSTMENTS & MAINTENANCE
tension adjustment
Preset desired tension (0-8) by turning the knob at the rear of the tool – the higher the number,
the tighter the tension capacity.
0 = 15 lbs 1 = 20 lbs 2 = 30 lbs 3 = 40 lbs
4 = 50 lbs 5 = 60 lbs 6 = 70 lbs 7 = 75 lbs 8 = 80 lbs
daily inspection
Keep a daily tool inspection log for damaged or warn parts.
Tension Capacity Indicator
Tension Adjustment Knob

7
SCHEMATIC & PARTS LIST