STREAM LABS Control User manual

Catch and control water issues. Anytime, anywhere.
StreamLabs®Control

Introducing the StreamLabs®Control
Brass body with stainless
steel ball valve
Robust ABS housing
NSF-61 Certied IP 54 / IP 56 Rating*
Open/Close Valve buttons
Valve position
Water-ow &
Calibration status
Wi-Fi status
Power override Power port
*IP 54 rated for indoor use, IP 56 rating achievable
with available outdoor enclosure
Wi-Fi reset button

Setup and Installation
Return to App to Adjust
Alerts & Shut-o Settings
Install Control:
Make sure there is a sucient Wi-Fi signal
where you plan to have the StreamLabs
Control installed, then follow instructions
in the installation guide included in the
StreamLabs packaging.
3 4
Pair Control to Wi-Fi:
Don’t worry about installing your Control
just yet. Sit somewhere comfortable,
plug in your Control, and follow the
instructions in the StreamLabs App to
pair your Control to Wi-Fi.
CAUTION: Valve rotation could cause injury.
Please keep clear of valve while in operation.
1 2
Download App

works with
1. Go to your device’s app store.
2. Search “StreamLabs water”.
3. Click on the StreamLabs App.
4. Click download.
How to Download the StreamLabs®App
Make your Water Even SmarterTM
StreamLabs works with other smart home devices like Amazon Alexa and Nest to automatically
put your Control in home or away mode.
Visit www.StreamLabswater.com/alexa or www.StreamLabswater.com/nest to learn more.

Important Safety and Installation Information
Make your Water Even SmarterTM
StreamLabs works with other smart home devices like Amazon Alexa and Nest to automatically
put your Control in home or away mode.
Visit www.StreamLabswater.com/alexa or www.StreamLabswater.com/nest to learn more.
• Note: This product is NOT intended to serve as/or replace primary
water shuto.
• Please refer to included documentation for installation instructions,
warnings, and diagrams.
• This product must be installed downstream of primary water shuto
and pressure reduction valve.
• If the installation location does not have a primary water shuto
and/or pressure reduction valve, install these rst prior to beginning
the installation of the StreamLabs Control.
• Not intended for outdoor installation (crawl space is an acceptable
installation location).
• Refer to installation insert for instructions on opening the valve in the
event of power loss.
• All included installation paperwork and disclosures can be found
online at https://support.StreamLabswater.com.

In the Box
• StreamLabs®Control
• Union ttings [depending on model]
• Power supply
• Temporary Bypass Flow Tube
• Installation instructions
• Additional StreamLabs Control barcode to scan during Wi-Fi setup
Requirements
• Wi-Fi 802.11b/g/n, 2.4 GHz (WEP, WPA, WPA2 encryption supported)
• Broadband internet connection with at least 2 Mbps upload/download speed
• Access to power outlet (DC power extension cables available on
www.StreamLabswater.com)
• Access to inlet water supply
• Not intended to replace primary shuto, to be installed aer primary shuto and PRV
• Free StreamLabs App and a compatible iOS or Android device
• Creation of a free StreamLabs account and acceptance of terms of service, which can be
found online at www.StreamLabswater.com
• Indoor use only
Specications
• StreamLabs Control dimensions: 8.0” (L) x 3.4” (W) x 5.4” (H)
• StreamLabs Control weight: 3.5 lbs (not including ttings)
• DC power supply cable length: 10 feet (DC power supply extender cables included on
www.StreamLabswater.com)
Support and Limited Warranty
• 2 year electronics warranty, 7 year brass warranty
• For full support, visit: https://support.StreamLabswater.com
Patent: www.StreamLabswater.com/patents Note: 9V battery for temporary alternate power not included

CAUTION: In order to protect the contact pads on the underside of the
Monitor, please do not ROTATE, SLIDE, or TWIST the Monitor on the pipe.
To adjust or move the Monitor, raise the Monitor off the pipe so that the
pads are not touching the pipe. If you need to change the location of a
Monitor that is already fastened to the pipe, cut the fasteners, remove
the Monitor, and reapply using the spare pipe fasteners in the box.
NOTE: Remember to remove the protective film covering the contact
pads before attempting installation.

Federal Communications Commission Regulations
FCC & IC DisclosureF
NOTE: This equipmenthas been tested and found to comply with the limits for a Class B digital device, pursuant to part 15of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates,uses and can radiate radio frequency energy and,if not installed and used inaccordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference willnot
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help.
This device complieswith Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should
be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
Additional Information, Warnings and Certifications Industry Canada Regulations
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et
d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.
This equipment complies with the ICES RF radiation exposure limits set forth for an uncontrolled environment. This equipment should
be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
Cet équipement est conforme aux limites d’exposition aux radiations ICES définies pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et une partie de votre corps
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device
may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présentappareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Antenna Information
NOTE: The UFCV-1000 Module bearing FCC ID: 2AHFE-UFCV1000 and IC: 21143-UFCV1000 has been approved by the FCC and ISED
to operate with the antenna types listed below with the maximum permissiblegain and required antenna impedance for each
antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device.
Inverted F PCB antenna, +0.97dBi peak
Le présent émetteur radio RM-10002705, FCC ID: USKRM-10002705, IC: 11898A-10002705 a été approuvé par FCC y ISED pour
fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour
chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont
strictement interdits pour l'exploitation de l'émetteur.
Antenne F inversée pour circuit imprimé, pic de 0,97 dBi

Contact Us
Website: www.StreamLabswater.com
Support: https://support.StreamLabswater.com
Email: [e-mail]
Phone: [phone]