Streamline ARCISAN Kudos KU04118 User manual

Kudos Dual Inlet/Outlet Toilet Suite
KU04118
Installation Guide
Dimensions are in millimeters and are subject to manufacturing variations. Streamline
reserves the right to vary specications at any time without notice. Information provided
within this installation sheet is correct at the date of printing. Please conrm all
particulars with your sales consultant prior to purchase.
Version: 1.1 - October 2016
www.streamlineproducts.com.au | Ph: 1300 735 352
This Kudos Dual Inlet/Outlet Toilet Suite is designed for
a left or right hand bottom inlet installation.
A 1/2” male thread will need to be plumbed in at the
location shown.
The standard set-out for a S-Trap is 110-160mm.
All distances are from final floor or finished wall.
The installer will need to supply the stop tap.
For bottom inlet the installer will also need to supply
the flexible hose for connection between the inlet and
the stop tap.
A 500mm length flexible hose will suit most installations
but the required length is dependent on the position of
the stop tap.
A
B
1
17 0
min 17 0 min
190 max 190 max
Bottom
Inlet
Back
Inlet
110 -16 0
185
165
125
65
745
Optional elbow for set out 160-220mm (JT34)

1
Place the pan in
position ensuring
it is centred in
accordance with the
centre line of the outlet.
Mark location of pan xing bolts.
2
Remove pan, drill holes for xing bolts and attach brackets.
3
For S Trap installation, cut horizontal pipe to required length
and t seal. Attach wall xing kit to elbow, push elbow into
the pan collar and adjust to correct height. Fix to wall and
adjust to ensure the elbow is vertical.
4
Attach pan bolts, into holes, as shown.
6
Locate the pan in
the nal position.
Screw threads into
oor mount brackets.
55
7
Fit outlet seal to bottom of outlet mechanism. Do not place
outlet seal on pan and then sit cistern on top!
2
NOTE:
If you have a bottom inlet cistern, follow instructions
on the top of page 3 (A).
If you have a back inlet cistern, follow instructions on
the bottom of page 3 (B).
55mm
5
Ensure screws are centred when the cistern is placed on
the pan.

3
A
8
Remove bung plug and inlet mechanism. Attach 1/2” thread
as shown. Connect exible hose to bottom of cistern.
B
8
Remove inlet mechanism. Locate the cistern onto the pan.
Screw down tightly to ensure a seal between the bolt head
and the bottom of the cistern.
10
Check if the inlet valve is under normal operation and adjust
the inlet valve oat adjustment thumbscrew clockwise (for
higher oat & water level) or anticlockwise (for lower oat &
water level).
Screw inlet hose onto stop tap. Place inlet valve into position
within the cistern.
9
10
Join the inlet mechanism hose
to the thread and replace inlet
mechanism. Connect exible
hose to stop tap.
Bottom Inlet
Back Inlet
9
Feed hose through hole in pan and locate the cistern onto the
pan. Screw down tightly to ensure a seal between the bolt
head and the bottom of the cistern.

4
Technical and Service - Ph: 1300 735 352 | Email: [e-mail]
11
Button Install: Remove nut.
Nut
12
Insert buttons into the hole on the lid. Slide nut over the bottom
of the rods and tighten. Fill and check water. Replace lid and test.
13
Seat Install: Insert expansion plugs into holes in pan.
14
Screw in the post and gasket, lightly, into the plugs that have
been inserted into the pan. Rotate the hinges so the posts are
positioned approximately at 11 and 1 (as shown above).
15
Push seat onto the posts and close lid. Move the seat around
until it is square with the pan.
16
Remove seat from pan. Tighten screws to nal tension. Slide
covers over seat mount. Replace seat on pan.
Please leave the instructions with the owner.