Streetwize SWPB1 User manual

The WEEE symbol on this product means that this product should be ethically
dismantled or recycled to minimise environmental impact. Please check with your
local authority for more information.
IMPORTANT: ADDITIONAL SAFETY INFORMATION: This Jumpstart & Powerbank is
NOT intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they are
supervised or have been given instruction concerning use of the Jumpstart &
Powerbank by a person responsible for their safety.
Please read these instructions carefully
before operating this device.
It is recommended to charge the
unit for 3 hours before
any use.
Streetwize Accessories: Sales enquiries: [email protected]
Technical enquiries: [email protected] www.streetwizeaccessories.com
Lancashire
BL9 9NB
Next Generation Portable
Emergency Jumpstart
& Powerbank
12V - 400Amp
A POWERFUL but compact 400Amp-(peak) emergency Jumpstart for most 12V
vehicles. PLUS a Power Bank that also provides HOURS OF PORTABLE POWER for
smart phones, laptops, or tablets and much more when out and about!
RoHS
COMPLIANT
Emergency Jumpstart & Powerbank contents:
Emergency Jumpstart & Powerbank
12V battery clips
USB charge cable with 4 built-in
assorted adaptors.
240V mains plug.
12V in-car charging plug.
interchangeable power
lead with 8 adaptors.
Charging the Emergency Jumpstart & Powerbank:
1. Insert either the 12V In-car charger or 240V mains power cable into the
15V/1A input port on the unit.
1. Insert the plug end into the require power socket. The LED’s (blue) will
flicker to indicate charging, 5 lit LED’s will indicate a FULL charge.
Charging smart phones etc:
1. Insert the USB charging plug into the 5V 2.1A USB output port.
2. Insert the correct adaptor for the device to be charged.
3. When the cable is connected Press the “On” button to charge the device.
12
12 3
SWPB1 Manual AW:Layout 1 6/10/15 12:29 Page 1

Emergency Jumpstart Operating Instructions:
generally a vehicle can be jump started with only 2 power LED’s (blue) lit on
the unit, however it is preferable to use a fully charged unit. DO NOT USE THE
CHARGER WITH LESS THAN 2 LED’s LIT
1. Connect the crocodile clips in the following order. Positive (+ Red)
charging lead to the positive (+ Red) terminal. Connect the negative (-
Black) charging lead to the negative (- Black) terminal. It is important that
the crocodile clips are making good contact with the battery terminals.
2. Connect the crocodile clips into the Jumpstart power outlet.
3. Turn the key to start the vehicle engine. If the engine does not start
immediately turn off the engine, wait at least 15 seconds.
4. When the vehicle starts, unplug the power supply plug from the unit and
remove the crocodile clips from the battery.
Caution: Never connect the red & black crocodile clips together.
Always use the charger at normal room temperature, never use near a naked
flame. Store in a cool dry place
12
34
Charging Instructions:
The unit has multiple charging outputs 12V & 19V. Press the power on button
(1) to select the required voltage, the LED’s (2) will light to show the chosen
voltage. Laptops and larger gadgets generally require a 19V power supply.
Charging laptops etc:
1. Insert the 12V in-vehicle or 240V mains power lead into the output
power point of the unit.
2. Choose the correct connector to connect the laptop or other device to
the unit.
2. Insert the correct connector onto the power lead and connect the device
to the powerbank unit. Press the “On” button.
12
1 2 3
SWPB1 Manual AW:Layout 1 6/10/15 12:29 Page 3