Streetwize SWPP3 User manual

STORAGE
This unit may be stored in any position. Make sure the clamps are secure inside the booster cable storage covers.
Store at room temperature. If not used for a prolonged period of time, recharge every 2 months in the winter and
every month in the summer.
WARNING! EXPLOSION HAZARD
DO NOT EXPOSE BATTERY TO FIRE OR INTENSE HEAT AS IT MAY EXPLODE.
BATTERY CONTAINS NON-SPILLABLE SEALED LEAD ACID BATTERY: IF CASE SHOULD BECOME CRACKED,
DISPOSE OF IMMEDIATELY TAKING ADEQUATE SAFETY PRECAUTIONS TO PREVENT INJURIES OR DAMAGE TO
PERSONS OR PROPERTY. BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
SPECIFICATIONS
Battery: 12 volt 8AH sealed lead acid, maintenance free, spill-proof, rechargeable.
Power Supply DC Output: 12-volts nominal. Up to 10 Amps with auto reset protector
Power Supply Charging Time: 24 hours with AC charger;
6 hours to recharge with 12-volt DC charger.
Storage Temperature: Store in a cool dry area.
The WEEE symbol on this product means that this product should be ethically dismantled or recycled to
minimise environmental impact. Please check with your local authority for more information.
IMPORTANT: ADDITIONAL SAFETY INFORMATION
This Power Station/Emergency Jumpstart is NOT intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are supervised or
have been given instruction concerning use of the Power Station/Emergency Jumpstart by a person responsible
for their safety.
12v Portable Power Station &
Emergency Jumpstarter
SWPP3
WELCOME: This product has been carefully engineered and manufactured to give you dependable operation.
Please read this manual thoroughly before operating your new product as it contains the information you need to
become familiar with its features and obtain the performance that will bring you continued enjoyment for many
years. Please keep this manual on file for future reference.
IMPORTANT: PRIOR TO USE, READ AND UNDERSTAND ALL WARNINGS, CAUTIONS AND INSTRUCTIONS INCLUDED
IN THIS INSTRUCTION MANUAL, AND THOSE PUBLISHED BY YOUR VEHICLE BATTERY MANUFACTURER AND
MANUFACTURER OF ANY DEVICE INTENDED TO BE USED WITH THIS UNIT.
RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
LOCATION OF CONTROLS
1. The rotary switch on the left hand side of the unit controls the power to the booster cables.
Always leave this in the “OFF” position except when jumpstarting a vehicle.
2. 3 LED Work Light.
3. 12 Volt Power Outlet.
4. Battery Status Check Button.
5. Reverse Polarity Indicator LED.
6. Battery Charging/Status Indicator LED.
7. Charging Jack.
8. USB Power Outlet.
9. USB/LED On/Off switch.
10. Negative (Black) Crocodile Clip.
11. Positive (Red) Crocodile Clip.
12. AC Charger.
13. DC Charging Cord.
FIRST AID:
Make sure fresh water and soap are available nearby in case battery
acid contacts skin, eyes or clothing. If contact with battery acid occurs,
rinse immediately and thoroughly with water. Then wash with soap and water.
Obtain immediate medical attention if redness, irritation or pain is present. For eye contact, flush eyes for at least
15 minutes and obtain immediate medical attention.
CAUTIONS
• Never work alone with this product. Make sure that someone is available to give assistance if needed.
• Wear complete eye and clothing protection. Do not touch eyes while working near battery.
• Do not attempt to remove or replace the battery used in this device. When the battery has reached the
end of it’s useful lifetime, take the entire unit to a battery recycling facility.
• For proper and safe operation of the 12 Volt DC power accessory outlets, do not place anything into it
except the plug of the accessory to be used.
• Remove metal personal jewelry, such as rings, bracelets, necklaces and watches while working with a
lead-acid battery. It can produce a short-circuit that may cause severe burns.
• Never charge or jump-start a frozen battery.
• Never allow clamps (positive & negative terminals) to touch together or to connect the same piece of
metal to prevent short-circuits and arcing.
• Do not operate this device while wearing vinyl clothing. Static electricity may be generated when vinyl
clothing is rubbed.
• This product is not intended for use in the rain or temperatures above 130˚F.
• Use only the provided chargers, cables and clamps. Unauthorized parts may damage the unit.
1
1
9
2
6
87
3
4
11
10
5
12 13
Streetwize Accessories: Sales enquiries: [email protected]
Technical enquiries: [email protected] www.streetwizeaccessories.com
RoHS
COMPLIANT
M17 1RY
SWPP3 Manual AW 2016.qxp_Layout 1 10/10/2016 12:37 Page 1

JUMP-STARTING A VEHICLE
1. Turn off the vehicle ignition and all accessories (e.g. radios, lights, air conditioners and cellular phones).
2. Set the emergency brake and put vehicles with automatic transmission in park position.
3. Make sure the Jump Start System Power Switch is in OFF position.
4. Determine the polarity of the vehicle’s battery terminals. The positive (POS, P, +) battery terminal usually is
larger in diameter than the negative (NEG, N, -) terminal. If you are unsure, you should refer to the vehicle’s
owner’s manual.
5. Determine whether your vehicle uses a negative or positive grounded system: Negative ground system –
Negative battery terminal is grounded to chassis. Most vehicles use this system.
Positive grounded battery terminal is grounded to chassis or any other part of the vehicle. If you are unsure, you
should refer to vehicle owner’s manual.
6. Never allow clamps (positive & negative terminals) to touch together or to contact the same piece of metal to
prevent short-circuits and arcing.
7. Follow instructions for a negative grounded system or positive grounded system as indicated below:
Negative Grounded System:
a. Securely connect the positive (+) red clamp to the positive (POS, P+) terminal of the vehicle battery or the
remote positive (+) terminal if equipped.
b. Check that vehicle is negatively grounded (most vehicles). Securely connect the negative (-) black clamp to the
vehicle chassis, engine block or a non- moving metal part of the vehicle which is verified to be grounded. Do not
clamp directly to negative battery terminal, carburetor, fuel lines, or sheet metal body parts. Check cable
connection polarity indicator.
c. See jump-starting step 8 to continue.
Positive Grounded System:
a. Securely connect the negative (-) black clamp to the negative (Neg, N-) ungrounded terminal of the vehicle
battery.
b. Securely connect the positive (+) red clamp to the vehicle chassis, engine block or a non-moving metal part of
the vehicle which is verified to be grounded. Do not clamp directly to positive battery terminal, carburetor, fuel
lines, or sheet metal body parts.
c. See jump-starting step 8 to continue.
8. The Reverse Polarity Indicator on the Jump Starter will illuminate RED for wrong connection and GREEN for
right connection.
9. When correct clamp connection is made, turn the Jump Start System Power Switch to ON position.
10. Allow 2 or 3 minutes of charging time. It is recommended to have a second person to assist holding the unit
securely in place during the next steps.
11. Turn on the vehicle to attempt to start the engine. If the vehicle does not start after 4 to 5 seconds of engine
cranking, then stop. Wait 3 to 4 minutes, and then try again. Repeat several times until the vehicle starts.
12. Standing as far away from the vehicle battery as is practical, disconnect the clamps in reverse sequence to
connecting procedure:
For negative grounded systems, first disconnect negative (black) then positive (red) clamps.
For positive grounded systems, first disconnect positive (red) then negative (black) clamps.
• This product is not a toy. Keep out of the reach of children.
• Keep battery terminals clean. Be careful to keep corrosion from coming in contact with eyes.
• Do not operate this unit in or around water. Water can damage the unit.
• If battery acid comes into contact with eyes, flush the eyes with water for at least 10 minutes. Seek
medical attention immediately.
• Always turn the Jumpstart Sustem off when not in use. Store in a cool, dry place.
• Do not open the Jumpstart System. There are no servicable parts in the unit. Doing so will void the warranty.
CHARGING AND RECHARGING
• Fully recharge the unit when red charging indicator light is on.
• The charging Red LED indicator will be illuminated while charging. When charging is complete the Red LED
changes to Green. This LED will not go out until the charging plug is removed.
• Do not charge the unit for more than 36 hours by AC charger and 12 hours by DC charger continuously.
• Do not charge the unit on a boat, boat ramp, or dock since the electrical cords and outlets used for charging could
cause severe electrical shock if they get wet.
• It is recommended that the unit be in an upright position while charging.
NOTE: Make sure both cable clamps (positive and negative) are placed in their storage holsters when not
in use.
CHARGING WITH AC CHARGER:
1. Press the battery status check button, if the battery status Green LED illuminates it will indicate a full charge.
2. If the SWPP3 requires charging, insert AC charger plug into charging jack of the unit.
3. Insert AC charger receptacle plug into AC receptacle.
4. The battery status Red LED will illuminate while charging.
5. Full charge takes approximately 24 hours.
6. The Red LED changes to Green, when charging is complete, unplug the AC charger receptacle plug then the
AC charger from the charging jack on the unit.
CHARGING WITH 12-VOLT CHARGER:
1. Press the battery status check button, if the battery status Green LED illuminates it will indicate a full charge.
2. If the SWPP3 requires charging, insert DC charger plug into charging jack of the unit.
3. Insert DC charger accessory plug into vehicle cigarette lighter socket.
4. The battery status Red LED will illuminate while charging.
5. Full charge takes approximate 6 hours, while the car engine is running.
6. The Red LED changes to Green, when charging is complete, unplug the DC charger accessory plug first and then
the DC charger from the charging jack on the unit.
WARNING: Do not overcharge this unit. Prior to charging unit, read and understand all instructions for
this unit. Overcharging may result in damage to the unit.
IMPORTANT WARNING: This product is only supplied with a minimal amount of charge at manufacture,
therefore for this product to operate correctly it has to be fully charged for a period of 24 hours
IMMEDIATELY after purchase, this is essential BEFORE ANY USE! & cannot be used DURING the charge
period. Failure to adhere to these conditions may invalidate the products warranty.
SWPP3 Manual AW 2016.qxp_Layout 1 10/10/2016 12:37 Page 3