Streetwize SWPB1 User manual

Emergency Jumpstarter
& Portable Power Bank
A POWERFUL but compact 400Amp-(peak) Emergency
Jumpstarter for most 12V vehicles. PLUS a Power Bank that
also provides HOURS OF PORTABLE POWER for smart phones
or tablets and much more when out and about!
SWPB1
12V -
400Amp
Emergency Jumpstart & Power Bank contents:
Emergency Jumpstarter & Power Bank
12V Smart Jumpstart Cables
(protects jumpstarter &
vehicle battery).
240V mains plug.
12V in-car charging plug.
USB charge cable with
3 built-in assorted adaptors.
Laptop charging lead with 8 adaptors
Emergency Jumpstart Operating Instructions:
The unit can jump start vehicles with a minimum of 3 LED’s lit. However for
optimum performance fully charge the unit (5 LED’s lit). NEVER USE THIS PRODUCT
TO JUMPSTART WITH LESS THAN 3 LED’s LIT AS THIS CAN CAUSE PROBLEMS AND
DAMAGE THE PRODUCT.
1. Connect the crocodile clips in the following order. Positive (+ Red) charging lead to the
positive (+ Red) terminal. Connect the negative (- Black) charging lead to the negative
(- Black) terminal. It is important that the crocodile clips are making good contact with
the battery terminals.
2. Connect the crocodile clips into the Jumpstarter power outlet.
3. Turn the key to start the vehicle engine in no longer than 4 second bursts. If the engine
does not start immediately turn off the engine, wait at least 15 seconds.
4. When the vehicle starts, IMMEDIATELY unplug the power supply plug from the unit and
remove the crocodile clips from the battery.
Please READ & UNDERSTAND the instructions carefully before operating this device, and
retain for future reference.
IT IS RECOMMENDED TO CHARGE THE UNIT FOR AT LEAST 3 HOURS BEFORE ANY USE AND TO
KEEP IT FULLY CHARGED WHEREVER POSSIBLE.
PLEASE NOTE: The Emergency jumpstart will NOT jumpstart a vehicle if it has a Voltage rate is
above 12.3V (a good level of charge). If the vehicle does not start this may indicate another
problem. Please have the vehicle checked by a qualified mechanic.
SWPB1 Manual AW 2019.qxp_Layout 1 29/03/2019 09:25 Page 2

1 2
3 4
1 2 3
Caution: Never connect the red & black crocodile clips together at the same time.
Always use the charger at normal room temperature, never use near a naked flame. Store
in a cool dry place.
DO NOT use or store at temperatures above 50°C or below -10°C.
Function on Smart Battery Cable
1) Reverse polarity connection: Solid Red LED with fast 2 short beep.
2) Short-circuit protection: Solid Red LED with long beep (Beeping as 3.3Hz Frequency).
3) Over-heat protection: Solid Red LED with long beep (Beeping as 2Hz Frequency).
4) Over-discharging protection: Solid Red LED with 2 short beep.
5) Green/Red LED flashing: Searching for status connection.
6) Green LED: Correct connection after one beep.
Do not use any charger cable other than those specifically provided with the
Jumpstarter/Powerbank for jumpstarting or charging.
To connect to battery. Connect Red (+) Croc Clips to Positive (+) battery terminal,
followed by Black (–) Croc Clips to (–) terminal. To remove the Croc Clips, remove Black (–)
Croc Clips followed by Red (+) Croc Clips.
1 2
3 4
Charging Instructions: The Power Bank has multiple voltage charging outputs 19V & 12V
(1 & 2) or charging input 15V/1A (3). Insert the power cable into the appropriate power
point 19V/3.5A (1) or 12V/2A (2) on the unit.
1 2 3
PLEASE NOTE: Laptops & larger gadgets generally require a 19V power supply.
SWPB1 Manual AW 2019.qxp_Layout 1 29/03/2019 09:25 Page 3

1 2 3
12 3
12
Charging smart phones etc:
1. Insert the USB charging plug into the 5V 2.1A USB output port.
2. Insert the correct adaptor for the device to be charged.
3. When the cable is connected Press the “On” button to charge the device.
Charging laptops etc:
1. Plug in the power connector into the required 19V or 12V output power point.
2. Choose the correct adaptor to connect the laptop or other device to the Power Bank.
3. Insert the correct connector onto the power connector lead and connect the device to
the Power Bank unit. Press the “On” button.
Charging the Emergency Jumpstart & Powerbank:
1. Insert either the 12V In-car charger or 240V mains power cable into the 15V/1A
input port on the unit.
2. Insert the plug end into the required power socket. The LED’s (blue) will flicker to
indicate charging, 5 lit LED’s will indicate a FULL charge.
SWPB1 Manual AW 2019.qxp_Layout 1 29/03/2019 09:25 Page 4

M17 1RY
RoHS
COMPLIANT
Warnings: The power bank will generate heat when charging. Use it in a well ventilated
area when charging. Keep the power bank away from heat sources, direct sunlight,
humidity, water or other liquids.
Do not operate the power bank if it is wet or damaged to prevent electrical shock,
explosion and/or injury. Improper repairs of this device may place the user at risk.
Do not use the power bank with wet hands. Keep the input ports free from dust, lint, etc.
which prevents good connections. Do not use this unit for anything other than its intended
use. The power bank is not a toy. Keep out of reach of children.
Do not charge under pillows, blankets. Do not store in a car during hot weather.
Short-circuiting a Li-ion battery can cause it to ignite or explode. Never open a Li-ion
battery’s casing. Li ion batteries contain safety devices that protect the cells inside from
abuse, if damaged these can cause the battery to ignite or explode.
Do not charge the power bank and charge an electronic device at the same time. This will
shorten the power bank’s battery life.
THE MANUFACTURER AND SUPPLIER HOLDS NO RESPONSIBILITY FOR DAMAGE CAUSED
BY INCORRECT OR IMPROPER USE OF THE PRODUCT. PLEASE READ AND RETAIN THE
INSTRUCTIONS FOR FUTURE REFERENCE.
The WEEE symbol on this product means that this product should be ethically
dismantled or recycled to minimise environmental impact. Please check with your local
authority for more information.
IMPORTANT: ADDITIONAL SAFETY INFORMATION: This Jumpstarter & Power Bank is
NOT intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they are supervised or
have been given instruction concerning use of the Jumpstart & Power Bank by a person
responsible for their safety.
LED Torch
Press and hold the power button
(1) to turn on the LED torch,
then press again to select.
SOS FLASHING or STROBE (fast)
Press again to turn off.
1
Streetwize Accessories:
Unit 1, Royce Trading Estate, Ashburton Road West,
Trafford Park, Manchester M17 1RY
Sales enquiries: [email protected]
Technical enquiries: [email protected]
Telephone: [phone]
www.streetwizeaccessories.com
WARRANTY: The 12 month warranty on this product will need to be activated within
30 days of purchase, please go to our web site and click on the “Warranty” link and
enter your details on the warranty screen. www.streetwizeaccessories.com.
SWPB1 Manual AW 2019.qxp_Layout 1 29/03/2019 09:25 Page 1