Strymon OJAI R30 User manual

USER MANUAL

OJAI R30 - High Current DC Power Supply User Manual ®
pg 2
Getting Started
Connect one end of the
included IEC cable to the 24V
power adapter, and the other
end to an AC power outlet.
Connect one end of the
included power adapter cable
to the 24V power adapter.
Connect the other end of the
power adapter cable to Ojai
R30’s 24V IN jack.
12
3

OJAI R30 - High Current DC Power Supply User Manual ®
pg 3
Connect Your Pedals
PEDAL OUTPUTS: Connect up to five DC pedals with the included 5.5mm x 2.1mm pedal cables.
Each output is dual-isolated for noise-free operation.
NOTE: Use non-adjustable outputs first to power your Strymon pedals. If using adjustable
outputs with Strymon pedals, make sure these outputs are set to 9V.
Check with each pedal manufacturer for recommended voltage, polarity, and required
current. If a pedal requires more than 500mA of current, or voltages other than 9, 12 or 18,
please find details on those configurations here: strymon.net/support/ojai-r30
• 9V OUTPUTS
Three outputs provide
500mA of available current
at 9V and have center
negative polarity.
• ADJUSTABLE OUTPUTS
Two outputs provide selectable 9V, 12V, or 18V
DC, each with center negative polarity. Each
output provides 500mA of available current at
9V, 375mA at 12V, and 250mA at 18V. Make sure
these outputs are set to 9V before connecting
your Strymon pedals.
• LED INDICATOR
Each output features
an LED indicator. LED
illuminates green when a
pedal cable is plugged in.
LED will turn off if cable is
unplugged, or the current
draw on the output exceeds
the maximum amount
available.

OJAI R30 - High Current DC Power Supply User Manual ®
pg 4
Ojai R30 is Expandable
Is your pedalboard growing?
Gain more outputs by linking Ojai units (sold separately) to the 24V THRU jack. Ojai R30 is part of a truly
expandable, modular power distribution system that can grow with your pedalboard.
Learn more about linking Ojai units to your Ojai R30: strymon.net/support/ojai-r30
Ojai R30 provides a huge amount of power. You can link together as many as 7 Ojai units powered from one 24V
power adapter, powering up to 35 effects pedals (depending on the total current requirement for the pedals).
While it’s unlikely that anyone would go to such extremes, we wanted to ensure that the Ojai product family
delivers maximum flexibility and expandability. A much more likely scenario would be to link 2 or 3 Ojai units
together, powering a combination of up to 15 high and low current draw pedals.
NOTE: Ojai units can be linked to a Strymon Zuma power supply for the ultimate in power and flexibility.
TO CONNECT OJAI UNITS TO YOUR OJAI R30:
Power your Ojai R30 with the included PS-124 power adapter, or the 24V OUT of another
Strymon power supply using the included EIAJ-05 cable.
Connect the 24V THRU on your Ojai R30 to the 24V IN on another Ojai unit using its included
EIAJ-05 cable.
Link additional Ojai units in the same manner.
1
2
3

OJAI R30 - High Current DC Power Supply User Manual ®
pg 5
Locate the Drill Template that is included in the box. It is also available for download at strymon.net/
support/ojai-r30.
Choose your mounting location. Tape the Drill Template, logo side up, in the location you want to install
your Ojai R30.
This illustration shows mounting to the top of your pedalboard. To mount Ojai R30 to the bottom of your
pedalboard, turn the pedalboard over before placing the Drill Template logo side up in the location you
want to install your Ojai R30.
Drill holes. Drill through the two marked
hole locations with a 1/8” (3mm) bit.
Remove the drilling template.
Attach Ojai R30. Place the Ojai R30 over
the holes. Install from the reverse side
of your pedalboard using the provided
#4 screws (3/8”).
1
3
4
2
DRILL TEMPLATE
HOLE LOCATIONS
#4 SCREWS
Installation Instructions
Ojai R30 features built in threaded hardware for easy mounting to the top or bottom of most pedalboards.