Summer My Bath Seat User manual

My Bath Seat® with Toys
OWNER’S MANUAL
Thank you for purchasing My Bath Seat® with Toys from Summer Infant.
While this product has been designed to comply with all applicable safety standards and regulations,
please remember to NEVER leave your child unattended at any time.
There is no substitution for adult supervision. Always keep baby within adult’s reach.
Please read the following instructions
and warnings carefully
KEEP THIS INSTRUCTION MANUAL
AND SAVE FOR FUTURE REFERENCE.
For technical support, contact us at 1-401-671-6551
or www.summerinfant.com/contact
Product is suitable for babies able
to sit up unassisted (approximately 5 months of age).
STOP using when baby begins pulling to a
standing position (approximately 10 months of age).
Adult assembly and installation required.

NOT A SAFETY DEVICE
Babies have DROWNED while using bath seats.
• ALWAYS STAY WITHIN ARM’S REACH OF YOUR BABY.
• Product is suitable for babies able to sit up unassisted
(approximately 5 months of age).
• STOP using when baby begins pulling to a standing position
(approximately 10 months of age).
• Suction cups will only properly adhere to a smooth, clean
surface.
• NEVER use in a sink.
• ALWAYS firmly lock all 3 suction cups to interior adult tub walls
according to provided instructions. Check for secure fit before
each use. Pull on each of the connections to assure secure fit.
• NEVER use product in non-rectangular tub, oval, Jacuzzi or
whirlpool style tub, or any tub that has water jet nozzles.
• ONLY use in standard rectangular adult tub with inner width
dimensions of 21-24 inches.
• Discontinue the use of the product if it becomes damaged,
broken, or disassembled.
• NEVER bathe baby until you have tested the water temperature.
ALWAYS check water temperature before placing child into
bath seat.
• Bath water should be between 90 and 100°F (32.2 and 37.8°C).
PREVENT DROWNING:
• Babies can drown in as little as 1 inch (2.5 cm) of water. Use
as little water as possible to bathe your baby.
• NEVER rely on a toddler or preschooler to help your baby or
alert you to trouble. Babies have drowned even when other
children are in or near the bathtub.
WARNING

components
3
• NEVER allow other children to substitute for adult supervision.
Parent or adult caregiver must always be present within arm’s
reach of the infant in the bath seat regardless of the
circumstances.
• NEVER allow a second child in the tub when bath seat is in
use.
• DO NOT fill adult tub over max fill water line mark located on
seat.
FALL HAZARD: Prevent serious injury from falling.
• NEVER lift or carry baby in bath seat.
Rear Suction Cup
C
Side Extending Arms
D
Side Suction Cups (2)
E
Locking Dials (3)
F
Locking Tabs (2)
G
Front Hanging Toys
H
Suction Cup Tray Toy
I
Play Tray
J
Rear Extending Arm
B
Bath Seat
A
A
B
D
D
C
E
E
F
F F
G
H
I
J

4
pushpush
Fully extend Rear Locking Arm
until both Locking Tabs on the arm
"click" open on back side of seat.
This will ensure the arm
is locked in place.
Place bath seat at rear of standard adult rectangular tub
(with inner dimensions of approximately 21-24 inches wide).
installing the bath seat
2
1
"click & lock”
"click & lock"
"click & lock”
"click & lock"
NEVER use product in a sink,
non-rectangular tub, oval,
Jacuzzi or whirlpool-style tub,
or any tub that has water jet
nozzles.
Ensure Rear Suction Cup is flush against rear tub wall.
Firmly press suction cup against tub wall.
Rotate Locking Dial clockwise
to lock suction cup in place.
Rear Suction Cup will swivel and rotate
to allow for optimal contact,
in case rear tub wall is angled.
WARNING

bath seat installation (continued):
3
4
Turn Screw Nobs
towards the
lock icon
Turn Locking Dial
towards the
lock icon
Turn Screw Nobs
towards the
lock icon
Turn Locking Dial
towards the
lock icon
Rotate Locking Dials on Side Extending Arms evenly
until Side Suction Cups make contact with interior side walls of tub.
5
Continue rotating Locking Dials
until Red Indicators are no longer visible.
See illustrations below.
installing the bath seat (continued)
Red!Red!
Red!
Red!

1
Turn all Locking Dials
to wards the
unlock icon
Rotate Locking Dials on Side
Extending Arms until
they are no longer in contact
with interior walls of tub.
6
Pull on Suction Cup tabs to break
the seal with the tub wall.
1
2
1
2
3
Turn all Locking Dials
towards the
unlock icon
Pull on Suction Cup tabs to break
the seal with the tub wall.
removing the bath seat
installing the bath seat (continued)
5
IMPORTANT: Before
bathing child, ENSURE bath
seat and all 3 suction cups are
securely locked in position to
interior tub walls.
!
PREVENT DROWNING: Babies can drown in as
little as 1inch (2.5 cm) of water.
ALWAYS bathe your infant using as little water
as necessary.
ALWAYS keep baby within adult's reach.
Never ll adult tub past the "Max Fill Level" mark.
WARNING
MAX
FILL LEVEL

3
2
removing the bath seat (continued)
7
pushpush
Pull on Suction Cup tabs
to break the seal with
the tub wall.
Rotate Locking Dial
counter clockwise to
release Suction Cup
from rear tub wall.
presspress
press
Press both Locking Tabs
on Rear Extending Arm
inward and push arm fully
back into bath seat.
1
2

•Surface-clean suction cups and bath seat after each
use with warm water and mild soap.
•Dry with clean towel.
•Product should be completely dry before any long
periods of storage.
• When stored, make sure
suction cups are not creased
or folded.
cleaning
Colors and styles may vary.
MADE IN CHINA.
D0000000772 7/20
Summer Infant (USA), Inc.
1275 Park East Drive
Woonsocket, RI 02895 USA
1-401-671-6551
© 2020 Summer Infant (USA), Inc.
Summer Infant Canada
200 First Gulf Blvd., Unit C
Brampton, Ontario, Canada, L6W 4T5
1-905-456-8484
storage
We’re here to help! If you have questions or need assistance,
please contact our Consumer Relations Team at
1-401-671-6551 or www.summerinfant.com/contact
attaching tray and toys
• Before each use, inspect the bath seat for damaged components, missing parts or sharp edges.
• Do not use product if any parts are missing or broken.
maintenance
1
2
To remove tray
To remove toys
Pull on
Suction Cup
tab to break
the seal with
the tray
• To clean toys, wipe clean and
completely dry before storing.
For the squirting sh toy,
squeeze all the water out and
dry before storing.