Sunbeam Sleep warm. Sleep well. User manual

HHEEAATTEEDDPPRROODDUUCCTT
U
U
s
s
e
e
r
r
M
M
a
a
n
n
u
u
a
a
l
l
S
Sl le ee ep pw wa ar rm m. .S Sl le ee ep pw we el ll l. .™™
P.N. 119352-000-000
www.sunbeam.com
BED6322 BeddingMan06-Just English.qxd 3/8/06 12:17 PM Page 1

Warnings and Safeguards
As with all electrical products, misuse of product or failure to properly
follow the instructions may cause overheating, fire or personal injury.
Please read the product label and all of the instructions before using
your heated product.
1. Do not use this heated product with an infant, a child, an
incapacitated or immobile person, a paraplegic, a quadriplegic,
a diabetic, one insensitive to heat such as a person with poor
blood circulation, or anyone who cannot clearly understand the
instructions and/or operate the controls.
2. Do not route electrical cords between the mattress and box spring.
Do not allow the cords to be pinched.
3. Do not use with damaged cords. Damaged cords can lead to fire.
Do not tuck in, trap, fold, cross or pinch cords between bed slats,
mattress or springs, or against walls, footboards or bed frame.
4. Do not dry clean this heated product. Cleaning liquid may damage
the insulation of the heating element. Improper laundering may
cause problems with the heating wire which can lead to fire.
5. Do not tuck in, pinch, flex or expose the heating wire to rubbing.
A damaged heating wire may result in possible overheating or fire.
Do not tuck the heated product or supply cord in a sofa or other
furniture. All portions of the heated product and controller should
be visible at all times.
6. Turn off or unplug the control for the heated product when
not using.
7. Wrapping the cord around the controller may damage the cord.
Loop loosely when storing.
IMPORTANT INSTRUCTIONS
DO NOT DESTROY
BED6322 BeddingMan06-Just English.qxd 3/8/06 12:17 PM Page 2

8. Keep the control away from drafty areas that may become damp
or wet such as an open window.
9. Do not use pins; they may damage the electric wiring.
10.Be sure this blanket/mattress pad/throw is used only on an AC
supply current circuit of 110-120 volts. Do not use with an
extension cord.
11.May experience increased heat in areas where heated product
is bunched or folded while in use.
12. Keep all dogs, cats and other pets away from this heated product.
This is an electrical appliance that they can damage or be injured by.
13. Do not use blanket/mattress pad on a waterbed, sofa, bunk
bed or mechanically adjustable bed and do not use throw
on a waterbed, bunk bed or mechanically adjustable bed.
14. For throw blankets: Do not use with rocking chairs, recliners,
chairs with casters or wheels, or other furniture subject to
movement.
15. Do not use another electronic heating device in conjunction
with your heated product.
16. Use the proper size blanket/mattress pad for your bed. For
example, use a Twin Size warming blanket on a Twin Size bed.
17. If the following Important Instructions are not followed, the
heated product will not operate properly.
18. Not for hotel, motel or other institutional use.
19. If you see the heated product operating improperly, unplug it
immediately and call Sunbeam Consumer Care in the U.S at
800-892-7684 or in Canada at 800-667-8623.
IMPORTANT INSTRUCTIONS
DO NOT DESTROY
BED6322 BeddingMan06-Just English.qxd 3/8/06 12:17 PM Page 3

S
Sl le ee ep pw wa ar rm m. .S Sl le ee ep pw we el ll l. .™™
Welcome
Thank you for choosing a Sunbeam®heated product. With your
purchase you’ve made a real investment in your comfort and can
look forward to staying warm and cozy for many cool days to come.
With over 50 years of experience and over 25 million households
using a Sunbeam®heated product, rest comfortably knowing that
you can trust the Sunbeam®brand for quality and performance.
So get ready for a more restful sleep.
BED6322 BeddingMan06-Just English.qxd 3/8/06 12:17 PM Page 4

1
Control Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Auto-Off & Preheat Features . . . . . . . . . . . . . . . . . . . . . 2
Heated Blanket and Mattress Pad
Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Control Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Warming Throw
Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Control Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . 7-8
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
How to Obtain Warranty Service . . . . . . . . . . . . . . . . . 10
Table of contents
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.
If you have any questions while setting up or using your product,
please visit us on the World Wide Web at: www.sunbeam.com or
contact Sunbeam Consumer Care in the U.S. at [phone]
or in Canada at [phone].
BED6322 BeddingMan06-Just English.qxd 3/8/06 12:17 PM Page 5

2
Control Chart
ON
OFF
SmartSense™ChoicePlus™StyleSmart™EliteStyle™
EasySet™PrimeStyle™AOPrimeStyle™
Auto-Off & Preheat Features
Auto-Off Feature
(selected models only):
The “Auto-Off” feature is designed for conservation of energy by
automatically turning your blankets or mattress pad off after
10 hours of continuous use (3 hours for throws).
For Dual Controls: Each control operates independently
and will turn off 10 hours after the control is turned “On”.
Note: After a power outage, the “Auto-Off” feature automatically resets the timer.
To restart all heated products after a power failure:
Press the power button and the heated product will begin to warm.
Preheat Feature
(selected models only):
The preheat function will heat the bed for a period of 30 minutes and the control will return to its original
setting.
1To use the preheat feature, simply turn on the warming product by pressing the “On/Off” button and then
press the “Preheat” button.
The display will show “PH” while the function is activated.
2To reset the preheat feature, simply turn off the control by pressing the “On/Off” button and then turn it
back on by pressing the “On/Off” button.
For questions or support, please visit: www.sunbeam.com
G85
(Single Control)
G85KQ
(Dual Control)
❂
10 hour
10
❂
❂
❂
❂
❂
Style Number
Backlit Display
Auto-Off
Warming Settings
Silent Operation
Preheat
Easy Operation
Easy Grip
Interchangeable Top
Auto Dimmer
85P
(Single Control)
85KQP
(Dual Control)
❂
10 hour
20
❂
❂
❂
❂
SimpliTouch™
H85
(Single Control)
H85KQ
(Dual Control)
❂
10 hour
10
❂
❂
❂
N85AP
Throw
3hour
3
❂
❂
❂
K85P
(Single Control)
K85KQP
(Dual Control)
10 hour
10
❂
❂
❂
❂
J85P/J85D
(Single Control)
J85KQP/
J85KQD
(Dual Control)
10
❂
❂
❂
❂
M85AP
Throw
3hour
3
❂
❂
❂
M85P
Throw
3
❂
❂
❂
BED6322 BeddingMan06-Just English.qxd 3/8/06 12:18 PM Page 6

1Place the heated blanket/mattress pad on the bed with the label at the foot
of the bed facing upward.
2Connect the cord into the module at the bottom of the heated blanket/
mattress pad until the plastic hinges click into place.
CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could
result from a loose connection.
3Run the control cord on the floor under the bed. Do not sandwich cord
between the mattress and box spring. Avoid any tangling or pinching.
4Control Placement:
• Dual Control for heated blanket or mattress pad –
place primary control (label on back of control)
on the right side of the bed.
run cord
under the bed
Mattress Pad
Cord Connector
Secondary
Control
Primary
Control
Flag Tag Label
Power
Cord
Module
Left Side
Right Side
1
3
4
5
2
3
Heated Blanket and Mattress Pad Set Up
CAUTION: Do not plug main power cord into the wall outlet until you have completely
set up your heated product per the instructions.
• Disconnect power cord from wall before detaching control from heated product.
• Always make sure cords are NOT trapped or pinched between bed slats, mattress,
springs, against wall, foot board or bed frame, or between furniture, walls or chairs.
CAUTION: Do not attempt to force the plug. This appliance has a polarized plug (one blade is wider than the
other). To reduce the risk of electrical shock, this plug is intended to fit only one way into an outlet. If the
plug does not fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
IMPORTANT
run cord
under the bed
Blanket Cord Connector
Primary
Control
Flag Tag
Label
Power
Cord
Module
Left Side
Right Side
2
1
3
4
5
2
See Control Features on page 4
for your individual control.
If there is a flashing light or
your control displays a flashing
“FF”, see page 8.
For questions or support, please visit: www.sunbeam.com
• Single Control for heated blanket or mattress pad –
the control can be placed on either side of the bed.
5Plug power cord into a 110-120 volt wall outlet.
(Label on back
of control)
(Label on back
of control)
BED6322 BeddingMan06-Just English.qxd 3/8/06 12:18 PM Page 7

4
SmartSense™
ChoicePlus™
StyleSmart™
EasySet™
Features:
• INTERCHANGEABLE COVERPLATES – Two colors included
•DIGITAL CONTROL – with backlit LCD for nighttime viewing
•AUTO-OFF – 10 hour independent auto-off (see page 2)
• 10 TEMPERATURE SETTINGS – select your personal comfort level
• SILENT OPERATION – no clicking when adjusting the temperature
•PREHEAT – for cozy warmth before bedtime (see page 2)
•SOLID STATE – for accurate and consistent heat control
• EASY OPERATION – electronic digital control for easy operation
• EASY GRIP – ergonomic control for easy operation
G85
(Single Control)
G85KQ
(Dual Control)
Control Features
Features:
•DIGITAL CONTROL – with backlit LCD for nighttime viewing
• AUTO-OFF – 10 hour independent auto-off (see page 2)
• 20 TEMPERATURE SETTINGS – select your personal comfort level
• SILENT OPERATION – no clicking when adjusting the temperature
• PREHEAT – for cozy warmth before bedtime (see page 2)
• SOLID STATE – for accurate and consistent heat control
• EASY OPERATION – electronic digital control for easy operation
• EASY GRIP – ergonomic control for easy operation
85P
(Single Control)
85KQP
(Dual Control)
ON
OFF
Features:
• DIGITAL CONTROL – with backlit LCD for nighttime viewing
• AUTO-OFF – 10 hour independent auto-off (see page 2)
• 10 TEMPERATURE SETTINGS – select your personal comfort level
• SILENT OPERATION – no clicking when adjusting the temperature
• SOLID STATE – for accurate and consistent heat control
• EASY OPERATION – electronic digital control for easy operation
• EASY GRIP – ergonomic control for easy operation
H85
(Single Control)
H85KQ
(Dual Control)
Features:
• BACKLIT DIAL – for easy nighttime viewing of the warming setting
• 10 TEMPERATURE SETTINGS – select your personal comfort level
• SOLID STATE – for accurate and consistent heat control
• EASY GRIP – ergonomic control for easy operation
• AUTO DIMMER – the lighted dial will automatically dim after 60 seconds
J85P/J85D
(Single Control)
J85KQP/J85KQD
(Dual Control)
Using Your Control:
1To turn the control on, press the “On/Off” button.
Note: For the SmartSense™, ChoicePlus™and StyleSmart™controls, the backlit display light will reset itself
by flashing “88” and then will return to the previous setting and will begin to warm.
2Adjust the warming setting to your personal comfort level by rotating the top knob left or right.
3To turn the heated blanket/mattress pad OFF simply press the “On/Off” button.
CAUTION: ALWAYS turn the heated blanket/mattress pad “OFF” when not in use.
For questions or support, please visit: www.sunbeam.com
SimpliTouch™Features:
• BACKLIT DIAL – for easy nighttime viewing of the warming setting
• AUTO-OFF – 10 hour independent auto-off (see page 2)
• 10 TEMPERATURE SETTINGS – select your personal comfort level
• SOLID STATE – for accurate and consistent heat control
• EASY GRIP – ergonomic control for easy operation
• AUTO DIMMER – the lighted dial will automatically dim after 60 seconds
K85P
(Single Control)
K85KQP
(Dual Control)
BED6322 BeddingMan06-Just English.qxd 3/8/06 12:18 PM Page 8

5
Features:
• 3 TEMPERATURE SETTINGS – select your personal comfort level
• SILENT OPERATION – no clicking when adjusting the temperature
• SOLID STATE – for accurate and consistent heat control
• EASY OPERATION – electronic control for easy operation
• EASY GRIP – ergonomic control for easy operation
• AUTO-OFF (Selected models only) – 3 hour Auto-Off operation (see page 2)
Using Your Warming Throw Control:
1To turn on the throw press the button in the middle of the control.
The indicator light will glow, depending on which setting the warming
throw is set, and the warming throw will begin to warm.
CAUTION: ALWAYS turn the warming throw “OFF” and disconnect
the power cord from the outlet when not in use.
2To turn the warming throw OFF press the button through the different
settings until the temperature setting lights are not glowing.
Module
Control
Power
Cord
Flag Tag
Throw Cord
Connector Throw Cord
Label
Module
Control
Power
Cord
Flag Tag
Throw Cord
Connector
Throw Cord
Label
PrimeStyle™
M85P
Non Auto-Off
When setting up your warming throw, be sure to follow the steps below in order.
1Locate the warming throw’s information label near the module.
2Connect the cord into the module at the bottom of the warming throw until
the plastic hinges click into place.
CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result
from a loose connection.
Warming Throw Set Up
For questions or support, please visit: www.sunbeam.com
2
1
3
2
1
3
3Plug the warming throw power cord into a 110-120 volt wall outlet.
CAUTION: Do not plug main power cord into the wall outlet until you have completely
set up your heated product per the instructions.
• Disconnect power cord from wall before detaching control from heated product.
• Always make sure cords are NOT trapped or pinched between bed slats, mattress,
springs, against wall, foot board or bed frame, or between furniture, walls or chairs.
CAUTION: Do not attempt to force the plug. This appliance has a polarized plug (one blade is wider than
the other). To reduce the risk of electrical shock, this plug is intended to fit only one way into an outlet. If
the plug does not fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
IMPORTANT
2
If there is a flashing light on
your control, see page 8.
EliteStyle™
N85AP
Control Features
PrimeStyle™AO
M85AP
Auto-Off
BED6322 BeddingMan06-Just English.qxd 3/8/06 12:18 PM Page 9

6
We recommend washing before initial use.
Before Washing or Storing Your heated product:
1Disconnect power cord from wall BEFORE detaching control cord from the heated product.
2Ensure that no cords are still connected and none of the wires have worn through the fabric.
3Carefully follow all washing instructions or your heated product may shrink and possibly
cause a fire hazard.
• DO NOT submerge control in water.
• DO NOT dry clean your heated product. Dry cleaning solvents may damage the wires.
• DO NOT use bleach or cleaning fluids.
• DO NOT use a wringer.
• DO NOT iron your heated product.
• DO NOT use mothballs or sprays of any kind.
• DO NOT reconnect the heated product or use it until it is COMPLETELY dry.
• DO NOT wash or put into water the power cord or any of the product’s cords.
Taking care of your heated product is easy and safe as long as you follow a few simple steps.
Machine Washing
1Presoak the blanket/mattress pad/throw for 15 minutes in mild soap and lukewarm water.
2Wash in mild soap and lukewarm water on the “delicate” or “gentle” cycle in the washer
for two minutes. Remember, do not use bleach.
3Rinse in fresh, lukewarm water.
4Spin dry in the washing machine. Then gently stretch to its original size.
Machine Drying
Caution: Do not use commercial dryers or the dryers at your local Laundromat.
They get too hot and would damage the wiring of the heated product.
1Preheat the dryer on the “low” temperature setting for 2 minutes.
2Place blanket/mattress pad/throw into the dryer and tumble dry for 10 minutes at a low temperature.
3Remove the blanket/mattress pad/throw while it is still damp and gently stretch it to its original size.
4Drape the heated product over a clothesline or a shower rod. DO NOT use clothespins.
5Heated product must be COMPLETELY dry before reconnecting the power plug or control plug.
Hand Washing
1Presoak the blanket/mattress pad/throw for 15 minutes in mild soap and lukewarm water.
2Gently squeeze the soap suds through a few times.
3Rinse in fresh, lukewarm water.
Hand Drying
1Gently stretch the blanket/mattress pad/throw back to its original size.
2Drape the heated product over a clothesline or hang over a shower rod. DO NOT use clothespins.
3Heated product must be COMPLETELY dry before reconnecting the power plug or control plug.
Care and Cleaning OF YOUR HEATED PRODUCT
For questions or support, please visit: www.sunbeam.com
BED6322 BeddingMan06-Just English.qxd 3/8/06 12:18 PM Page 10

QWho should NOT use the heated blanket, heated mattress pad or warming throw?
AThe following people should NOT use the heated blanket, heated mattress pad
or warming throw:
• An infant
• A child
• An incapacitated or immobile person
• A paraplegic
• A quadriplegic
• A diabetic
• Anyone insensitive to heat such as a person with poor blood circulation
• Anyone who cannot clearly understand the instructions and/or operate the controls
QWhat do the Underwriters Laboratories (UL / cUL) or (ETL/ cETL) labels mean? What do
either of these labels mean about safety of Sunbeam heated products?
AUnderwriters Laboratories (UL/cUL) develops product safety standards for a large range of
products and performs independent tests based on these standards. Products tested by
UL/cUL and which have passed all the safety standards are permitted to bear the UL/cUL
label. Intertek Testing Services (ETL/ cETL) is a certified, independent testing organization that
tests products in accordance with UL/ cUL safety standards and issues the ETL/ cETL label for
those products that meet the relevant UL/ cUL standards. All Sunbeam®products are tested
to UL/cUL standards and bear either the UL/ cUL or ETL/cETL label to indicate that the
product meets or exceeds UL/cUL or ETL/ cETL safety standards for heated products.
QI have heard that some heated products have EMFs.
What is this?
AEMF stands for Electromagnetic Field. This is an electrical field that surrounds any wire
that has current flowing along its length. Although several studies have been conducted to
evaluate the impact, EMFs have not been proven to be harmful. In any event, Sunbeam®has
reduced the strength of EMFs in its blankets/mattress pads/throws to very low levels.
QWhat do I do if my pet chews the cord, I lose my control or the control does not operate
properly?
APlease stop using the heated product immediately. Call our Consumer Service number
listed under How to Obtain Warranty Service and ask for instructions on how and where to
send the heated product.
QMy control feels warm to the touch. Is this a problem?
ANo. The control will feel warm to the touch when functioning properly.
7
Frequently Asked Questions OF YOUR HEATED PRODUCT
For questions or support, please visit: www.sunbeam.com
(FAQs continued on next page)
BED6322 BeddingMan06-Just English.qxd 3/8/06 12:18 PM Page 11

8For questions or support, please visit: www.sunbeam.com
QMy heated blanket/heated mattress pad/warming throw doesn’t heat properly.
AYour heated product is not a heating pad. It will not feel hot to the touch when laid out flat
in a normal manner. Try the following fold test to see if it is operating properly:
1Fold the heated blanket, heated mattress pad or warming throw 3 times over.
2Make sure the control cord is connected to the module and then
plug the power cord into an outlet.
3Turn on your heated product, then turn the control to the highest
setting and wait 5 to 7 minutes.
4Put your hand between the folds and you should feel the blanket/
mattress pad/throw warming up.
Caution: DO NOT continue the test for more than 7 minutes. DO NOT
attempt to make any internal adjustments to this appliance. If you have tried all of the
solutions above and the heated product still doesn’t work, stop using it immediately,
disconnect the power cord and contact Sunbeam Consumer Care.
QWhat does “FF” mean on my Electronic Digital Control?
AThe digital controls (SmartSense™, ChoicePlus™, StyleSmart™) are designed to notify you
in the event that a problem has been discovered by flashing “FF” on the display. Follow
instructions on the flag tag to reset control. First, check the
blanket/mattress pad for visual damage. If no visual damage is
found, unplug the system from wall outlet. Check that the control is
well-connected to the module. Plug the power cord into the wall outlet.
Set the control to “On.” If the system still does not operate after 2 or 3
times trying to reset, disconnect the power cord and contact Sunbeam
Consumer Care.
QWhat does a flashing light mean on my EasySet™, PrimeStyle™,
PrimeStyle™ AO or EliteStyle™ control ?
AThese controls are designed to notify you in the event that a problem has been discovered
by flashing the light on the control. Follow instructions on the flag tag to reset control.
First, check the heated product for visual damage.
If no visual damage is found, unplug the system from wall outlet. Check that the
control is well-connected to the module. Plug the power cord into the wall outlet
and turn the control On. If the product still does not operate after 2 or 3 times
trying to reset, disconnect the power cord and contact Sunbeam Consumer Care.
FF
Models:
ChoicePlus™,
StyleSmart™,
SmartSense™
BED6322 BeddingMan06-Just English.qxd 3/8/06 12:18 PM Page 12

9
Sunbeam Products Inc., doing business as Jarden Consumer Solutions (“Sunbeam”) warrants
that for a period stated below from the date of purchase, this product will be free from
defects in material and workmanship.
• All heated products branded Arlington™ will carry a ONE year limited warranty.
• All heated products branded Sunbeam®HomeChoice™, SlumberRest®Cuddler™ and
Cuddle Up®will carry a TWO year limited warranty.
• All other heated products branded Sunbeam®and SlumberRest®will carry a FIVE year
limited warranty.
Sunbeam, at its option, will repair or replace this product or any component of the product
found to be defective during the warranty period. Replacement will be made with a new or
remanufactured product or component. If the product is no longer available, replacement
may be made with a similar product of equal or greater value. This is your exclusive warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase
and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain
warranty performance. Sunbeam dealers, service centers or retail stores selling Sunbeam
products do not have the right to alter, modify or any way change the terms and conditions
of this warranty. This warranty does not cover normal wear of parts or damage resulting from
any of the following: negligent use or misuse of the product, use on improper voltage or
current, use contrary to the operating instructions, disassembly or repair or alteration by
anyone other than Sunbeam or an authorized service center. Further, the warranty does not
cover Acts of God, or Nature, such as fire, flood, hurricanes and tornadoes. Sunbeam shall not
be liable for any incidental or consequential damages caused by the breach of any express or
implied warranty. Except to the extent prohibited by applicable law, any implied warranty of
merchantability or fitness for a particular purpose is limited in duration to the duration of
the above warranty. Some states, provinces or jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights that vary from state to state.
Limited Warranty
BED6322 BeddingMan06-Just English.qxd 3/8/06 12:18 PM Page 13

10
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.
How to obtain warranty service:
We’re Here to Help. For any questions you may have about your heated
product, please visit our web site at: www.sunbeam.com or contact
Sunbeam Consumer Care in the U.S at 1-800-892-7684 or in Canada at
1-800-667-8623.
©2006 Sunbeam Products, Inc., doing business as Jarden Consumer Solutions. All rights reserved.
Distributed by Sunbeam Products, Inc., doing business as Jarden Consumer Solutions, Boca Raton, FL 33431
Imported and distributed by Sunbeam Corporation (Canada) Ltd, doing business as Jarden Consumer Solutions, 5975
Falbourne Street , Mississauga, Ontario L5R 3V8
Printed in China.
BED6322 BeddingMan06-Just English.qxd 3/8/06 12:18 PM Page 14