Sunbeam HOT-2-TROT TRAVEL IRON User manual

HOT-2-TROT TRAVEL IRON
Instruction Manual
www.sunbeamhome.com
MODEL 32610001
ITEM 17043
Printed in China
3 Year Limited Warranty
This device has a limited warranty of 3 years from the
original date of purchase against workmanship and
defects in material. If under normal use, your product
fails to operate, please contact our customer service
department at [email protected] . A replacement
or refund will be provided to you with proof of purchase.
Star Elite Inc. may deny claims of damage caused by
misuse or modifications of this product.
© 2023 Sunbeam Products, Inc. All rights reserved.
SUNBEAM®is a registered trademark of
Sunbeam Products, Inc. used under license.
Distributed by Star Elite Inc., Montreal, Canada H3B 3X9.
SE010-100523
Questions? [email protected]
or 1-877-383-6399
(8:30 am - 5:00 pm EST) Monday - Friday

IMPORTANT
SAFEGUARDS
When using electrical appliances, basic safety
precautions should always be followed including
the following:
READ ALL INSTRUCTIONS BEFORE USE
• Use iron only for its intended use.
• To protect against risk of electric shock, do not immerse
the iron in water or other liquids.
• The Steam Selector must be OFF when lling the
water in tank.
• Never yank cord to disconnect from outlet; instead,
grasp plug and pull to disconnect.
• Do not allow cord to touch hot surfaces. Let iron cool
completely before putting away. Loop cord loosely
around iron when storing.
• Always disconnect iron from electrical outlet when
lling with water or emptying and when not in use.
• Do not operate iron with a damaged cord or if the iron
has been dropped or damaged. To avoid the risk of
electric shock, do not disassemble the iron. Incorrect
reassembly can cause a risk of electric shock when the
iron is used.
• Close supervision is necessary for any appliance. Do
not leave iron unattended while plugged in or turned
on or on an ironing board.
• Burns can occur from touching hot metal parts, hot
water or steam. Use caution when you turn a steam
iron upside down – there may be hot water in the tank.
• If the iron is not operating normally,disconnect it from
the power supply.
• Your iron is designed to rest on the heel rest. Do not
leave the iron unattended. Do not set the iron on an
unprotected surface, even if it is on its heel rest.
• Note: We test each iron at the factory to ensure that
it functions correctly. The test may leave a small,
harmless amount of water within the water tank.
TO USE THE SHOT OF STEAM: Place the iron on top of the
wrinkle and press both the buttons each time you would
like an extra burst of steam. The Shot of Steam®feature
may be used continuously in approximately 3 second
intervals.
CARING FOR YOUR IRON AFTER USE
TURNING OFF YOUR IRON
TURNING OFF YOUR IRON
1. Turn the Steam Selector to (Dry) and Temperature
Select Dial to OFF.
2. Unplug the iron from the power source.
WARNING: NEVER yank the power cord when unplugging
the iron.This can damage the cord.
STORING YOUR IRON
1. Turn off and allow the iron to cool.
2. If you do not use your iron on a daily basis, empty the
water tank after each use for a longer iron life.To do so,
unplug the iron, turn the iron upside down, open the
ll hole cover, and allow water to ow from the Water
Fill Door. Shake the iron gently to remove trapped
water drops.
3. Loosely loop the power cord around the iron body and
store the iron on its heel rest.
Important: Wrapping the cord around the iron too
tightly can damage the cord.
MAINTAINING YOUR IRON
CLEANING THE SOLEPLATE
Clean the soleplate if starch or other residue accumulate.
TO CLEAN THE SOLEPLATE
Turn off and allow the iron to cool and then wipe it with
a soft, damp cloth.
WARNING: DO NOT use abrasive cleansers, scouring pads
or vinegar to clean the soleplate. This will damage the
nish.
TO FILL THE WATER TANK (use tap water)
1. Make sure the iron is unplugged. Set the Steam Selector
to (Dry) and the Temperature Select Dial to OFF.
2. Lift the Water Fill Door.
3. Pour tap water into iron water tank. Do not ll water
tank beyond maximum ll level.
WARNING: To prevent the risk of burns, be careful when
lling a hot iron with water. Hot metal parts, hot water
and steam can cause injuries.
DRY IRONING
1. Make sure the Steam Selector is turned to the (Dry)
setting.
2. Plug the cord into a 120-Volt AC outlet or 240 V based
on the specic country Electrical Output.
3. Select the temperature setting you desire using the
dial. Allow the iron to heat for 2 minutes. While the
iron is heating, make sure it is sitting on its heel rest
on a stable, protected surface.
WARNING:DO NOT turn the Steam Selector to ON position
when using the iron in Low temperature.
STEAM IRONING
1. Follow the instructions for “To Fill the Water Tank.”
2. Plug the cord into a 120-Volt AC outlet or 240 V based
on the specic country’s Electrical Output.
3. Select the temperature setting to either or MAX
using the dial.Allow the iron to heat for 2 minutes.
While the iron is heating, make sure it is sitting on
its heel rest on a stable, protected surface.
4. Turn the Steam Selector to the Steam Setting and
begin ironing.
Important: When not ironing, always set the Steam
Selector to (Dry) and the Temperature Select Dial to OFF.
USING THE IRON’S SPECIAL FEATURES
SHOT OF STEAM®FEATURE
Shot of Steam®feature provides an extra burst of steam
for deep penetration of stubborn wrinkles. You can use
this feature while Dry or Steam ironing, but the water
tank must be at least 1/4 full of water.
1
4
8
7
2
3
5
6
FEATURES OF YOUR
HOT-2-TROT TRAVEL IRON
1. Lens
2. Handle
3. Temperature Select Dial
4. Steam Selector
5. Water Fill Door
6. Water Tank
7. Soleplate
8. Shot of Steam Buttons (both sides)
9. Voltage Selector Switch (not shown)
SPECIAL INSTRUCTIONS
• To avoid a circuit overload, do not operate another high
wattage appliance on the same circuit.
• If an extension cord is absolutely necessary, a 15-ampere
cord should be used. Cords rated for less amperage may
overheat. Care should be taken to arrange the extension
cord so that it cannot be pulled or tripped over.
FOR PRODUCTS PURCHASED IN THE
UNITED STATES AND CANADA
To reduce the risk of electrical shock, this appliance has
a polarized plug (one blade is wider than the other). This
plug ts a polarized outlet only one way; if the plug does
not t fully into the outlet, reverse the plug. If it still does
not t, contact a qualied electrician. Do not attempt to
defeat this safety feature.
SAVE THESE INSTRUCTIONS