SunComm SC-385 User manual

SC-385
GSM VoIP Gateway
2 channels
User Manual

【Content】
1.INTRODUCTION.................................................................................................................1
2.FUNCTION DESCRIPTION...............................................................................................1
3.PARTS LIST..........................................................................................................................1
4.DIMENSION .........................................................................................................................2
5.CHART OF THE DEVICE..................................................................................................3
6.CABLING..............................................................................................................................4
7. IP SETTING.........................................................................................................................5
8.WEB PAGE SETTING.........................................................................................................7
9.SYSTEM INFORMATION..................................................................................................8
10. ROUTE................................................................................................................................9
11.MOBILE ............................................................................................................................14
12.NETWORK........................................................................................................................17
13.SIP SETTING....................................................................................................................21
14. NAT TRANS.....................................................................................................................29
15.SYSTEM AUTH................................................................................................................30
16.SAVE CHANGE................................................................................................................31
17.UPDATE ............................................................................................................................32
18.REBOOT............................................................................................................................34
19.SPECIFICATION.............................................................................................................35
20.SETUP SC-385 WITH ASTERISK.................................................................................36

-1-
1. Introduction
SC-385 is a 2 channels VoIP GSM Gateway for call termination (VoIP to
GSM ) and origination (GSM to VoIP). It is SIP based and compatible
with Asterisk. It can make 2 calls simultaneously from SIP VoIP devices
to GSM networks and GSM network to VoIP devices.
2. Function description
2.1 VoIP(SIP)、GSM(SC-385) conversion.
2.2 50 sets of LAN->MOBILE routes setting，50 sets of MOBILE->LAN
routes setting.
2.3 Voice response for setting and status (dial in from mobile).
2.4 Series connections to save bills.
2.5 Standard SIP(RFC2543,RFC3261) protocol，
Communicates with other gateway or Softphone via PC or notebook
3. Parts list
Please check the parts for any missing parts. If do, please contact
our agents：
3.1 「SC-385」main body
3.2 Power adaptor AC-DC (110V AC – 12V DC) or (220V AC – 12V DC)
3.3 Network cable
3.4 Antenna
3.5 User Manual

-2-
4. Dimension
(1)
(2)
(4)
(3)
14.5cm
17cm
4
.
1
cm

-3-
5. Chart of the device
5.1 Antenna：Antenna connector
5.2 DC 12V：Power input.
5.3 LAN：LAN port: It also can be DHCP Server.
5.4 WAN: RJ-45 internet connector，standard RJ-45 socket，connect to
HUB.
5.5 PWR (Power LED)：Light up when power is normal.
5.5 VoIP1：An indicator light of VoIP1
5.6 VoIP2：An indicator light of VoIP2
5.8 LINK Indicator：Light up when network is connected.
5.1
5.2 5.3 5.4 5.5 5.6 5.75.8

-4-
6. CABLING
6.1 Connect the internet cable from HUB to the ‘WAN’ connector of the
SC-385.
*If you need to stack up more SC-385,you can stack up as follows.
6.2 Connect the antenna and put it in proper position to get the best
signal reception.
6.3 Insert the SIM card from back of the main body. (take the slide off
first).
6.4 Connect the power adaptor. The ‘POWER’ LED should be light up.

-5-
7. IP Setting
The operator can setup or query the network parameters by dialing in the
mobile number which it SIM card has been put in the main body. The
status or result is response by voice. In the first 20 seconds after
power-on, the VoIP GSM Gateway enters the IP setting mode. The
operator may dial in the mobile number during this period to set or query
the network parameters.
Item IVR Action IVR Menu Choice Notes
1 Reboot #195# After you hear “Option
Successful,” hang-up. Unit will
reboot automatically.
2 Factory Reset #198# System will automatically
Reboot. WARNING: ALL
User-Changeable”
NONDEFAULT SETTINGS
WILL BE LOST! This will
include network and service
provider data.
3 Check IP Address #120# IVR will announce the current
IP
address , Default :
192.168.0.100
4 Check IP Type #121# IVR will announce if DHCP is
enabled or disabled.
default : OFF
5 Check Network
Mask #123# IVR will announce the current
network mask. Default :
255.255.255.0
6 Check Gateway
IP #124# IVR will announce the current
gateway IP address,

-6-
Address Default : 192.168.0.254
7 Check Primary
DNS Server #125# IVR will announce the current
setting in the Primary DNS
field.
Default : 192.168.0.1
8 Check Firmware
Version #128# IVR will announce the version
of the firmware running
9 Set as DHCP
client #111# The system will change to
DHCP
Client type
10 Set Static IP
Address #112xxx*xxx*xxx *xxx# DHCP will be disabled and
system will change to the
Static IP type.
Enter IP address using
numbers on the telephone key
pad. Use the * (star) key when
entering a decimal point.
11 Set Network Mask #113xxx*xxx*xxx
*xxx# Must set Static IP first. Enter value using numbers on
the telephone key pad. Use
the * (star) key when entering
a decimal point.
12 Set Gateway IP
Address #114xxx*xxx*xxx *xxx# Must set Static IP first. Enter IP address using
numbers on the telephone key
pad. Use the * (star) key
when entering a decimal
point.
13 Set Primary DNS
Server #115xxx*xxx*xxx *xxx# Must set Static IP first. Enter IP address using
numbers on the telephone key
pad. Use the * (star) key
when entering a decimal
point.

-7-
8. Web Page Setting
When the IP setting is done, the operator may setup all the rest
parameters via web page. Browse the IP address from Internet
Explorer (e.g. http://192.168.0.100)。The following page shows up：
Enter the username and password for authentication. (default
username=voip, password=1234). The page follows when the
username and password are correct.

-8-
9.System Information.
9.1 When you login the web page, you can see the demo system current
system information like firmware version, company… etc in this
page.
9.2 Also you can see the function lists in the left side. You can use
mouse to click the function you want to set up.

-9-
10. Route
10.1 Mobile TO LAN Settings
The operator may assign 50 sets of routing rule to transfer the call
incoming from MOBILE to LAN.
The Ssc-385 will transfer to the URL according to the caller ID of the
Mobile.
*CID：
(1) may enter the whole number, e.g. 0911111111
(2) only part of the number (prefix) e.g. 0911* means any number
starting with 0911 will be accepted

-10-
(3) * means all numbers can be accepted
(4) N means the calls without the CID
Please note the priority of the rules. The item which has more digits will
have higher priority. If the digits are the same, then former one gets the
higher priority.
*URL：The IP address to transfer this call
(1) may enter the whole IP address, e.g. 192.168.0.101 or proxy
extension .
(2)If this field is blank or simply ‘N’, it means refuse to transfer.
(3)If an ‘*’ entered, it means 2-stages-dialing. The call will be answered
and prompt dial tone again to receive the IP address as the
destination. The caller may enter the IP such as 192*168*0*101#.

-11-
10.2 Mobile to LAN Speed Dial Settings
When you set Mobile to LAN Speed Dial Settings and Mobile to
LAN at the same time,SC-385 will give priority to Mobile to LAN Speed
Dial Settings.
*The call will be answered and prompt dial tone again. When the caller
may enter the “Num”, system will connect the “URL” as destination.

-12-
10.3 LAN to Mobile Settings
The operator may assign 50 sets of routing rule to transfer the call
incoming from LAN to MOBILE.
The SC-385 will transfer to the mobile number according to the incoming
URL
*URL：The IP address of the incoming call
may enter the whole IP address, e.g. 192.168.0.101 or proxy server’s
extension. If a simple ‘*’ is entered, means no restriction for the
incoming IP address.

-13-
*Call Num：
1. may enter the whole number, e.g. 0911111111
2. a simple *”means 2-stages-dialing. The call will be answered and
prompt dial tone again to receive the called number as the
destination, e.g. 0911111111 or 0911111111#
3. #['d'n]['a'ppp] for one-stage dialing
[...] is option
'd'n means to delete the beginning n codes,
'a'ppp means to add 'ppp' in front.
for example #d2a09 means one-stage dialing,
delete the first 2 codes from your destination number,
then add 09 in front as the new destination number.

-14-
11. Mobile
11.1 Mobile Status
(1)Network Registration：The telecom carrier which the SIM card has
been registered
(2)SIM Card ID：SIM card ID.
(3)Signal Quality：Signal quality.
(4)Incoming IP：The IP address of the last incoming call from LAN
(5)Incoming IP Name: proxy server name
(6)Outgoing IP：The IP address of the last outgoing call to LAN
(7)Incoming Mob：The caller ID of the last incoming call from MOBILE
(8)Outgoing Mob：The called number of the last outgoing call to MOBILE

-15-
11.2 Mobile Setting
GSMVoIP Codec
LAN (5)Rx
(4) Tx
DTMF
(1)VoIP Tx Gain
(2) VoIP Rx Gain
(
1
)
(
2
)
(
3
)
(
4
)
(
5
)
(
6
)
(
7
)
(
8
)
(
9
)
(
10
)
GSMCodec
Rx
Tx
DTMF
Mobile 1:
Mobile 2:

-16-
(3)LAN Dial tone Gain: DTMF Receiver is not good, you can adjust gain
down.
(4)CODEC Tx Gain: as above
(5)CODEC Rx Gain: as above
(6)Caller ID: You may select to display the Caller ID from GSM incoming
call, or fixed SIP user name.
(7)Presentation CLIR: If you need to block the Caller Id for call
termination, please choose Suppression
(8)Mobile PIN Code: If you need to unlock pin code via SC-385, you can
click “On” and enter pin code.
(9)LAN Answer Mode:
Answered: when mobile answer, then connect the call
Alerted: when the mobile is ringing back tone, then connect the call
Income: when LAN dial out, then connect soon
(10)Band Type: When you buy Quad band, you need to choose your
GSM frequency

-17-
12. Network
In Network you can check the Network status, configure the WLAN
Settings, LAN Setting and SNTP settings.
12.1 Network Status: You can check the current Network setting in this
page.

-18-
12.2 WAN Settings: You can check the current Network setting in this
page.
(1) The TCP/IP Configuration item is to setup the WAN port’s network
environment. You may refer to your current network environment to
configure the system properly.
(2) The PPPoE Configuration item is to setup the PPPoE Username and
Password. If you have the PPPoE account from your Service
Provider, please input the Username and the Password correctly.
(3) The Bridge Item is to setup the system Bridge mode Enable/Disable.
If you set the Bridge On, then the two Fast Ethernet ports will be
transparent.
(4) When you finished the setting, please click the Submit button.