Sunix FTL-1218H-G Series User manual

771-FTLQIG000-NCI
Introduction DIN-Rail Install Step
Please check if the following items are present and in good condition upon opening
your package. Contact your vendor if any item is damaged or missing.
Industrial Ethernet Media Converter
Accessories
Din Rail Accessory Package 1
Wall Mountable Accessory Package 1
Fiber Lid 2
×
×
×
Features
Industrial grade design for stability and reliability
Extends 10/100/1000 LAN transmission distance up to 100KM with Single Mode
SC Fiber
Supports Link Fault Pass-through and far-end fault function
Supports 10/100/1000Base-T(X) auto negotiation and auto MDI/MDI-X
Built in a watchdog timer to monitor internal switching error
Relay output for power failure or port break alarm
Protect against electronic degradation and chemical corrosion
12V DC Jack & External power 12~48V DC terminal block with reverse polarity
protection
Detachable wall and DIN-rail mounting kit design
Plug-n-play & compact size designd
Extended operating temperature from -20~85 C
Version 1.0
The media converters have incorporated SUNIX advanced technologies
such as the RS-422/485 auto identify & switch, AHDC/CS (Auto Hardware
Direction Control / Carrier Sense) technology, and auto baud rate detection
feature. SUNIX MedIO media converter, a specialized equipment for industrial
application which can effectively protect your equipment from lightning,
electrostatic discharges, high voltage, and ground voltage damage, with
features like Surge Protection, Optical Isolation Protection, and Reverse
Power Protection. Fiber Ethernet media converters not only extends the
distances but also provide features like Link Fault Signaling, which allows
application to react to the situation.
FTL-1218H-Gx 10/100/1000 Base-TX to 1000Base-FX Media Converter
FTL-1218Hx 10/100 Base-TX to 100Base-FX Media Converter
Model Specification
Converter
I
n
d
u
s
t
r
i
a
l
SUNIX CD
Quick Installation Guide (This Document )
User Manual ( In CD )
Industrial Ethernet Media Converters
Wall-Mounting Install Step
Package List
Step 1
Head for lower clip
Holes for Screws
Step 2
Step 3
Step 4
Step 5
Hook space to hold
pin/screw at wall
Holes for Screw to fix wall
mount brackets
Power inputs & grounding
Note: This is option and if you tight this screw, DIN Rail mounting will be locked and
device can't be remove from DIN Rail without loosing this screw. You must tight this
screw after hanging the product at DIN Rail.
al
Quick Installation Guide

FTL-1218H-Gx Series
Version 1.0
FTL-1218Hx Series
Alarm set ON LED (Red)
(ON : Any DIP Switch Set ON)
(OFF : All DIP Switch Set OFF)
Fiber status LED (Orange)
(ON : Fiber Link OK)
(Flash : ACT status)
10/100/1000Base-TX LAN Port
Top Vie w
TEL: [phone]
FAX: [phone]
Website: www.sunix-ncci.com.tw
E-mail: [email protected]
Copyright© by SUNIX Co, LTD.
All rights reserved.
Power-1 On LED (Green)
By DC-Jack power in)(
Power-2 On LED (Green)
By MiniBlock power in)(
Data Transmission LED
(ON:LinkOK)
(Flash : Data Transmission)
Front Panel
Bottom View
Data Transmission LED
(ON:LinkOK)
(Flash : Data Transmission)
4-Pin DIP Switch :
No.1:power-1, enable alarm
No.2:power-2, enable alarm
No.3:RJ-45,enable alarm
No.4:Fiber, enable alarm
+V-V G
P-1 P-2
POWER IN
Power V+ Pin
Terminal Block Power In
Power V- Pin
Relay - Pin
DC-Jack Power in
RX
TX
10/100
ACT
/LINK
PWR-1
PWR-2
Alarm
Fiber
Industrial Ethernet Converter FTL-1218H-G Series
Fiber TX Port
Fiber RX Port
1000Base-FX Fiber Port
Converter
I
n
d
u
s
t
r
i
a
l
Industrial Ethernet Media Converters
321
ON
4
+-
Ground Pin
Relay + Pin
Alarm set ON LED (Red)
(ON : Any DIP Switch Set ON)
(OFF : All DIP Switch Set OFF)
Fiber status LED (Orange)
(ON : Fiber Link OK)
(Flash : ACT status)
10/100Base-TX LAN Port
Power-1 On LED (Green)
By DC-Jack power in)(
Power-2 On LED (Green)
By MiniBlock power in)(
Data Transmission LED
(ON:LinkOK)
(Flash : Data Transmission)
FrontPanel
Bottom View
Data Transmission LED
(ON:LinkOK)
(Flash : Data Transmission)
RX
TX
10/100
ACT
/LINK
PWR-1
PWR-2
Alarm
Fiber
Industrial Ethernet Converter FTL-1218H Series
Fiber TX Port
Fiber RX Port
100Base-FX Fiber Port
321
ON
4
Relay Hardware Installation Guide
+V-V G
P-1 P-2
POWER IN
+-
DC24V
4-Pin DIP Switch :
No.1:power-1, enable alarm
No.2:power-2, enable alarm
No.3:RJ-45,enable alarm
No.4:Fiber, enable alarm
ON : Alarm relay enable
OFF : Alarm relay disable
ON : Alarm relay enable
OFF : Alarm relay disable
Quick Installation Guide