sunjoe HJ602C User manual

© 2017 by Snow Joe®, LLC
All rights reserved. Original instructions. SAVE THESE INSTRUCTIONS
1
A Division of Snow Joe®, LLC Model HJ602C Form No. SJ-HJ602C-880E-MR3
2-IN-1 CORDLESS
GRASS SHEAR + SHRUBBER
3.6-V LITHIUM-ION
R
OPERATOR’S MANUAL
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Always follow these safety guidelines. Failure to do so may
result in serious bodily injury or death.
General Safety WARNINGS!
Notice the personal safety alert symbol m used in this manual
to draw your attention to a WARNING given along with the
particular operating instruction. This means that the operation
requires special ATTENTION, CAUTION, and AWARENESS.
When using this power tool, basic safety precautions, including
the following, should always be followed to reduce the risk of
re, electric shock, personal injury and material damage.
mWARNING! This unit can be dangerous! Careless or
improper use can cause serious injury.
mWARNING! The moving blades can cut you. Keep hands
and feet away from the blades and the cutting area.
Retain this manual for future reference and reread it at the start
of each trimming season.
mWARNING! This battery-operated power tool must be
recharged only with the specic charging unit for the battery. A
charging unit that may be suitable for one type of battery may
create a risk of re when used with another battery type.
• Avoid accidental starting.
• When the tool is not in use, keep it away from other metal
objects.
• Before operating the tool, read the entire manual carefully
and make sure you know how to switch the tool OFF in an
emergency.
Work Area Safety
1. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
2. Do not operate power tools in explosive atmospheres,
such as in the presence of ammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust, liquid or fumes.
3. Keep bystanders and children away. All bystanders,
including children and pets, should be kept a safe
distance away from the work area.
Electrical Safety
1. If the battery charger cable is damaged, please call the
Snow Joe®+ Sun Joe®customer service center at
1-866-SNOWJOE (1-866-766-9563).
2. If charging the power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected power supply. The using of an RCD reduces the
risk of electric shock.
3. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any earthed (grounded)
power tools or battery chargers. Unmodied plugs and
matching outlets will reduce risk of electric shock.
4. Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
5. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
6. Do not abuse the charging cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep cord
away from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
7. Battery charger is for indoor use only. Only charge this
battery-powered tool indoors.
Personal Safety
1. Stay alert. Watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the inuence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
2. Use personal protective equipment. Always wear eye
protection. Protective equipment such as a dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce the possibility
of personal injuries.
3. Avoid unintentional starting. Ensure all switches are in
the OFF position before connecting to the power source,
battery charger, or before picking up or carrying the tool.
Carrying power tools with your nger on the switch or
charging power tools with the switch ON can lead to
accidents.

2
4. Remove any adjusting key or wrench before starting
the power tool on. A wrench or a key left attached to a
moving part of the power tool may result in personal injury.
5. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
6. Dress properly. Do not wear loose clothing or jewelry.
Dangling articles such as these can become caught
in moving parts. Using rubber gloves and substantial
footwear is recommended when working outdoors. Wear
a protective hair covering to contain long hair.
7. Use dust-reducing equipment (e.g. dust masks) when
available. Using these devices can greatly reduce
dust-related hazards.
Power Tool Use and Care
1. Do not force the appliance. It will do the job better with
less likelihood of injury if it is used at the rate for which it
was designed.
2. Do not use the power tool if the switch does not turn
it on and o. Any power tool that cannot be controlled by
the switch is dangerous and must be repaired.
3. Disconnect the battery pack from the power tool
before making any adjustments, changing accessories
or storing the power tool. Such preventative safety
measures reduce the risk of starting the power tool
accidentally.
4. Store idle appliances indoors. When not in use,
appliances should be stored indoors in a dry and high or
locked-up place out of the reach of children.
5. Maintain appliance with care. Check for misalignment or
binding of moving parts, breakage of parts and any other
condition that may aect the power tool's operation. If
damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
6. Keep cutting blades sharp and clean. Properly
maintained cutting blades with sharp edges are less likely
to bind and are easier to control.
7. Use the power tool and accessories in accordance
with these instructions and in the manner intended
for the particular use of the power tool, taking into
account the working conditions and the work to be
performed. Using the power tool for operations dierent
from those intended could result in a hazardous situation.
8. Keep all parts of the body away from the cutter blade.
Do not remove cut material or hold material to be cut
when blades are moving. Make sure the switch is o when
clearing jammed material. A moment of inattention while
operating the product may result in serious personal injury.
9. Carry the product by the handle with the cutter blade
stopped. When transporting or storing the product,
always t the cutting device cover. Proper handling of
the product will reduce possible personal injury from the
cutter blades.
10. Hold the power tool by insulated gripping surfaces
only, because the cutter blade may contact hidden wiring.
Cutter blades contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
11. Check the hedge for foreign objects before operation,
e.g. wire fences. Take care that the cutting device does
not come into contact with wire or other metal objects.
12. Hold the product properly, e.g. with both hands if
two handles are provided. Loss of control can cause
personal injury.
Service
1. If your power tool requires service, contact an
authorized Snow Joe®+ Sun Joe®dealer or call the
Snow Joe®+ Sun Joe®customer service center at
1-866-SNOWJOE (1-866-766-9563). Only identical
replacement parts should be utilized for repairs. This will
ensure that the safety of the power tool is maintained.
2. If the battery charger cable is damaged, it must be
immediately replaced to avoid a hazard. Contact the
Snow Joe®+ Sun Joe®customer service center at
1-866-SNOWJOE (1-866-766-9563) for assistance.
Battery Safety Warnings
This manual contains important safety and operating
instructions for your battery and charger.
1. Before using the charger, thoroughly read all instructions
and cautionary markings on the charger and the cordless
grass shear + shrubber.
mWARNING! If the grass shear + shrubber housing is
cracked or damaged, do not insert the charging adapter into
the power tool or plug the power tool into the mains outlet.
There is a danger of electric shock or electrocution.
2. This charger is ONLY intended to charge this rechargeable
battery. Any other use poses a risk of re, electric shock
or electrocution.
3. Do not place any object on top of the charger or place
the charger on a soft surface that may result in excessive
internal heat. Keep the charger away from any heat
source.
4. To reduce the risk of damaging the electric plug and
cord, pull the plug, not the cord, when disconnecting the
charger from the electric outlet.
5. Make sure the battery charging cable is located in a safe
place so that it will not be stepped on, tripped over or
otherwise subjected to damage or stress.
6. An extension cord should not be used unless absolutely
necessary. Using an improper extension cord poses a risk
of re, electric shock or electrocution.
7. Do not operate the charger if it has received a sharp
blow or has become damaged in any way. Contact
the Snow Joe®+ Sun Joe®customer service center at
1-866-SNOWJOE (1-866-766-9563) before continuing use.

3
8. Do not disassemble the charger. If the charger requires
service or repair, contact an authorized Snow Joe®+
Sun Joe®dealer or call the Snow Joe®+ Sun Joe®
customer service center at 1-866-SNOWJOE
(1-866-766-9563). Incorrect reassembly poses a
risk of electric shock, electrocution or re.
9. To reduce the risk of electric shock, unplug the charger
from the outlet before cleaning the unit.
10. Never attempt to connect two (2) chargers together.
11. DO NOT store or use the tool and battery pack in
locations where the temperature may reach or exceed
104 ºF (40 ºC). Dangerous storing locations include
outdoor sheds or metal buildings in the summer.
12. The charger is designed to operate on standard household
electrical power (120 V). Do not attempt to use it with any
other voltage!
NOTE: The integrated battery is not fully charged out of
the carton. Read the safety instructions and then follow
the charging notes and procedures.
13. The longest life and best performance can be obtained if
the integrated battery is charged when the air temperature
is between 64.4 ºF – 75.2 ºF (18 ºC – 24 ºC). Do not
charge the battery pack when the air temperature falls
below 50 ºF (10 ºC) or above 104 ºF (40 ºC). Following
these safety measures will prevent damage to the
battery pack.
14. Do not incinerate the integrated battery even if it is
seriously damaged or completely worn out. The battery
can explode in a re.
Grass Shear + Shrubber
Safety Warnings
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for
their safety.
• Carry the machine by the handle with the cutter blade
stopped. Use the cover when transporting or storing the
tool. Proper handling of the machine will reduce possible
personal injury.
• During operation, hidden objects in shrubs, like wire and
cable, can be accidentally cut by the blade.
• Keep supply and extension cords at a safe distance from
the cutting attachment.
• Only use the tool in daylight or in good articial light.
• Before turning the tool ON and during operation,
make sure all body parts are at a safe distance from
the cutting attachment.
• Always ensure that the ventilation openings are clear
of debris.
• Keep in mind that the operator or user is responsible
for accidents or hazards occurring to other people or
their property.

4
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand and follow all
instructions on this tool before attempting to assemble and operate.
READ THE OPERATOR'S
MANUAL(S) – Read, understand
and follow all instructions in the
user manual(s) before attempting
to assemble and operate.
SAFETY ALERT – Indicates a
precaution, a warning or a danger.
WARNING! Do not expose the
unit to rain or wet conditions.
Keep dry.
Symbols SymbolsDescriptions Descriptions
Wear protective gloves and
non-slip footwear when using the
machine and handling debris.
Thrown objects and moving blade
can cause severe injury.
Only use battery charger indoors.
Battery charger contains a
safety transformer.
Risk of Injury. Use safety
glasses, hearing protection and
dust mask.
DANGER! Keep hands away from
blades.
WARNING! The cutting attachment
continues to move after the motor
is switched OFF.
Wear protective, slip-resistant
footwear during operation to
protect feet.
Keep bystanders a safe distance
away from the work area.

5
Know Your Cordless Grass Shear + Shrubber
Read the owner’s manual and safety rules carefully before operating your cordless grass shear + shrubber. Compare the
illustration below to the actual unit in order to familiarize yourself with the location of the various controls and adjustments.
Save this manual for future reference.
Technical Data
Charger Input 120 V
Charger Output 6 V 600 mA
Battery Voltage 3.6 V
Battery Capacity 1.5 Ah
Battery Type Lithium-iON
Shear Blade Length 3.3 in. (8.4 cm)
Shrubber Blade Length 5 in. (12.7 cm)
No Load Speed 900 rpm
Charger Included
Battery Runtime (Max) 45 min
Charging Time 3 hours
Weight 2.1 lbs (1 kg)
1. Charging socket
2. Charging indicator
3. Handle
4. Power ON/OFF trigger switch
5. Safety lock-o button
6. Safety tabs
7. Grass shear blade
8. Shrubber blade
9. Charger adapter
10. Charger plug
11. Grass blade sheath + shrubber blade sheath
(not shown)
1
2
35
6
7
8
9
Back of the handle
4
10
The other side of the unit

6
Unpacking
Carton Contents
• Cordless handheld unit + grass shear blade
• Shrubber blade
• (2) blade storage sheaths
• Charger
• Manuals with registration card
1. Carefully remove the cordless grass shear + shrubber and
check to see that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you nd damaged or
missing parts, DO NOT return the unit to the store. Please
call the Snow Joe®+ Sun Joe®customer service center at
1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging
material until you are ready to use your new cordless grass
shear + shrubber. The packaging is made of recyclable
materials. Properly dispose of these materials
in accordance with local regulations.
IMPORTANT! The equipment and packaging material are
not toys. Do not let children play with plastic bags, foils
or small parts. These items can be swallowed and pose a
suocation risk!
Assembly
This cordless grass shear + shrubber comes completely
assembled with the grass shear blade pre-installed.
mCAUTION! Wear protective gloves before handling
the blades.
mWARNING! Make sure the unit is powered o before
handling the blades.
Fitting and Changing the Blades
The grass shear + shrubber is equipped with two
interchangeable blades that are designed for do-it-yourself
grooming projects around your garden. The shrubber blade is
used to cut hedges and shrubs (Fig. 1) while the grass shear
blade is used to cut grass and hedges where ner detail is
required (Fig. 2).
1. Push the blade cover release button and slide the blade
cover towards the ON/OFF trigger switch (Fig. 3).
Fig. 1
Fig. 2
Fig. 3
Blade cover release button
Blade cover

7
2. Lift the cover away from the unit (Fig. 4).
3. Gently lift the blade out by grabbing the safety tabs
(Fig. 5).
4. Position the shrubber blade as shown aligning the holes
in the blade onto the drive pins. Verify that the rear part of
the blade is tucked under the rear housing tabs. This will
ensure a perfect alignment (Fig. 6).
5. Retting the drive cover, ensure that all four location legs
are properly lined up with the blade (Fig. 7).
6. Slide the blade cover towards the blade to secure (Fig. 8).
NOTE: If you have any questions, please call the Snow Joe®
+ Sun Joe®customer service department at 1-866-SNOWJOE
(1-866-766-9563) for assistance.
Before Using
Charging Procedure
The battery charger supplied matches the lithium-iON battery
installed in the tool. Do not use other battery chargers.
The lithium-iON battery is protected against deep discharging.
When the battery is empty, the machine will switch o and the
blade will no longer move.
Charge the battery up to 3 hours then use it until it runs down
(i.e. the tools starts to operate slowly). Recharge for up to 3
hours again before resuming operation.
mWARNING! Continued and excessive overuse of the
ON/OFF trigger switch can permanently damage the lithium-
iON battery.
mCAUTION! This charger does not automatically turn o
when the battery is fully charged. Please take care not to leave
the grass shear + shrubber plugged into the charger. Switch o
or unplug the charger at the mains when charging is complete.
Fig. 4
Fig. 5 Safety tabs
Fig. 6
Shrubber blade
Drive pins
Housing
tabs
Fig. 7
Location legs
Fig. 8

8
NOTE: The charge indicator light will illuminate red when
the charger is plugged in and is charging the grass shear +
shrubber. The indicator will turn green when the grass shear +
shrubber is fully charged.
The charging process starts as soon as the charger is plugged
into both the proper electrical outlet and the tool.
• During the charging procedure, the handle of the tool will
feel slightly warm to the touch. This is normal.
• When no further use is planned for an extended period of
time, disconnect the battery charger from the outlet and
the unit.
• Do not use the tool during the charging procedure.
Battery Charging
The length of service between each charging varies depending
on the type of work you are doing. The battery in this grass
shear + shrubber has been designed to provide maximum
trouble-free life. However, like all batteries, it will eventually
wear out. To obtain the longest possible battery life, we
suggest the following:
• Store and charge your grass shear + shrubber in a
cool area. Temperatures above or below normal room
temperature will shorten battery life.
• Never store the grass shear + shrubber with the battery
in a discharged condition. Recharge the unit immediately
after it is discharged.
• All batteries gradually lose their charge. The higher the
temperature is, the faster they lose their charge. If you
store your grass shear + shrubber for long periods of time
without using it, recharge the battery every 6 months. This
will extend battery life.
NOTE: The grass shear + shrubber has been shipped in a low
charge condition and should be fully charged before use.
1. Plug the charger adapter into an appropriate power outlet.
Connect the charger plug into the charging socket of the
grass shear + shrubber (Fig. 9).
2. The charging indicator will illuminate red when charging
(Fig. 9).
3. The battery will take up to 3 hours to charge due to
the level of charge left in the battery and the ambient
temperature.
NOTE: A charging indicator light will always be illuminated
when the charger is plugged in and the mains power is turned
on. The charging indicator indicates the charge status of the
grass shear + shrubber as shown below:
Operation
IMPORTANT! The product is intended for light-duty trimming
of shrubs and lawn edges for residential properties.
NOTE: Charge the battery then use it until it runs down (i.e. the
tool will only slowly operate and stop soon). Recharge again
before resuming operation.
mWARNING! The blades continue to move for a few
seconds after the tool is switched OFF. Turn OFF the tool and
wait until the blades come to a complete stop before adjusting
or cleaning.
mCAUTION! Never touch the blade rail while the tool is
in operation and be aware of the sharp edges even when the
grass shear + shrubber is not in use.
NOTE: Do not touch the moving blades.
Starting + Stopping
1. To power ON, push and hold one of the safety lock-o
buttons, while pressing the ON/OFF trigger switch with
your forenger. Once the trigger switch engages, you
can release the safety lock-o button and proceed with
operation (Fig. 10).
NOTE: The safety lock-o button reduces the risk of
accidental starting.
Fig. 9
Charging indicator
Charging Condition
Charging
Fully Charged
Color of
Charging Indicator
Red
Green
Fig. 10
Safety lock-o button
ON/OFF trigger
switch

9
2. To power OFF, simply release the ON/OFF trigger switch
(Fig. 10).
mCAUTION! Do not force the blades through dense
growth. If the blades slow down, then reduce your cutting
pace. Should the blades jam, release the trigger immediately.
Do not use your ngers to free up jammed blades. Jammed
blades can release suddenly causing serious injury.
mCAUTION! Always ensure proper footing and balance
in a clean and clear work environment before switching on the
grass shear + shrubber.
Trimming Tips
mWARNING! Only use the shrubber blade for this
operation.
NOTE: Try to keep the cutting device angled at approximately
15° to the cutting surface (Fig. 11).
1. Shaping – A hedge should be trimmed to achieve a
trapezoidal form; it should widen toward the bottom on
both sides. Shaping a hedge in this manner improves the
penetration of light to the lower extremities. A general
guideline is to slant the hedge approximately 4 in. (10 cm)
for each 39 in. (1 m) of hedge height.
2. Cutting Sequence – First cut both sides; start at the
bottom and work towards the top. This prevents cuttings
from falling into an area that you have yet to trim.
3. Trimming the Top – Where the branches have grown
extremely long, cut back the hedge in several stages. The
shorter cuttings obtained are best suited for composting.
4. Pruning Thick Branches – When older hedges are to be
cut a substantial amount, use pruning shears or some
other device to trim thicker branches (greater than 0.3 in.
[8 mm] in diameter) to the desired length before starting
work with the shrubber.
To shape precisely, run a taught line between the
extreme edges of the hedge and then trim along the
length of the line.
Ensure that the blade does not come into contact with any
object made of hard material that could damage it, such
as fencing wire or metallic plant supports.
Shearing Tips
mWARNING! Only use the grass shear blade for this
operation.
1. Avoid shearing grass in a stooped or bent over position for
lengthy periods of time. If prolonged stooping or bending
is unavoidable, then regularly interrupt by standing upright
and successively bending backwards several times.
2. Pay attention when performing work close to trees and
bushes. The cutting device can damage sensitive bark,
and damage fence posts.
3. Do not move the product too fast as this will result in
ineective cutting and possible damage.
4. Cut repeatedly from up and down in layers when the grass
is very high.
5. Keep the cutting device at an angle of about 10° to the
ground when shearing. Avoid touching the ground as this
can ruin the lawn and damage the product.
6. Let the cutting device do the work. Let it work at its own
pace, never press it into the area to be cut.
7. Carefully maneuver the product around objects, such as
trees and bushes, ensuring it does not come into contact
with them. Avoid that the cutting device comes in contact
with sensitive plants.
8. Our Environment – At Snow Joe®+ Sun Joe®, we care
about the environment and consider what we may do to
protect it. If you share this concern, you may already be
aware of the suggestions below; if not, please consider
them as a small step in protecting our future.
Don't throw your clippings in a trash bag; where possible,
dispose of your garden waste in a landll. Alternatively,
many communities provide a collection point where you
can dispose of your garden waste in an environmentally-
friendly manner.
Maintenance
mWARNING! Always switch the product o and let the
product cool down before performing inspection, maintenance
and cleaning work.
1. Keep the ventilation vents of the tool clean at all times. If
possible, prevent foreign matter from entering the vents.
2. If the enclosure of the product requires cleaning, do not
use solvents to clean it. Only use a moistened soft cloth.
Never let any liquid get inside the tool; and never immerse
any part of the tool into a liquid.
3. The blade rail should be cleaned and treated with light
machine oil or spray lubricant (such as WD40, CRC 5.56 or
RP7) after each use. When a job lasts for a long period of
time, it is recommended that the blade rail also be treated
with spray lubricant at regular intervals during operation.
4. Inspect the product before each use for worn and
damaged parts. Do not operate it if you nd broken and
worn parts.
Fig. 11
15°

10
Blade Maintenance
To ensure years of ecient and trouble-free operation, blade
cleaning should be performed if sap and debris have built-
up, or if you live in an area where the soil is sandy. Cleaning
unusually heavy deposits may require removal of the blades.
NOTE: Snow Joe®+ Sun Joe®will not be held responsible for
any damage or injuries caused by repair of the trimmer by an
unauthorized person or by mishandling of the trimmer.
1. Keep the cutting blades clean and free of debris.
Remove trimmings.
2. Apply a small amount of suitable lubricant on the blades
to retain a good cutting performance (Fig. 12).
3. Keep the blades sharp. Have a worn or damaged cutting
device replaced with a new one of the same type by a
qualied specialist. Spare parts may be ordered online at
snowjoe.com or via phone by contacting the Snow Joe®
+ Sun Joe®customer service center at 1-866-SNOWJOE
(1-866-766-9563).
Storage
When the tool will not be used for several months, it is ideal
to leave the battery connected to the charger. For optimal
storage, proceed as follows:
• Fully charge the battery.
• Clean the product as describe above.
• Assemble the blade covers over the blades.
• Store the tool in a secure and dry location. The storage
temperature must always remains in the range of
41 °F (5 °C) to 104 °F (40 °C).
• Before using the tool after prolonged storage, fully
recharge the battery.
Battery Caution + Disposal
Always dispose of your battery pack according to federal,
state, and local regulations. Contact a recycling agency in your
area for recycling locations.
mCAUTION! Even discharged battery packs contain
some energy. Before disposing, use electrical tape to cover
the terminals to prevent the battery pack from shorting, which
could cause a re or explosion.
mWARNING! To reduce the risk of injury or explosion,
never burn or incinerate a battery pack even if it is damaged,
dead, or completely discharged. When burned, toxic fumes
and materials are emitted into the surrounding atmosphere.
1. Batteries vary according to device. Consult your manual
for specic information.
2. Install only new batteries of the same type in your product
(where applicable).
3. Failure to insert batteries in the correct polarity, as
indicated in the battery compartment or manual, may
shorten the life of the batteries or cause batteries to leak.
4. Do not mix old and new batteries.
5. Do not mix Alkaline, Standard (Carbon-Zinc), or
Rechargeable (Nickel Cadmium, Nickel Metal Hydride, or
Lithium-Ion) batteries.
6. Do not dispose of batteries in re.
7. Batteries should be recycled or disposed of as per state
and local guidelines.
Service and Support
If your Sun Joe®2-in-1 cordless grass shear + shrubber
requires service or maintenance, please call the Snow Joe®+
Sun Joe®customer service center at 1-866-SNOWJOE
(1-866-766-9563).
Model and Serial Numbers
When contacting the company or reordering parts, you will
need to provide the model and serial numbers of your product.
These are found on the decal axed to the housing or handle
of your cordless grass shear + shrubber. Copy these numbers
into the space provided below.
H J 6 0 2 C
Record the following numbers from the housing or handle of your
new product:
Model #:
Serial #:
Fig. 12

11
HJ602C-27
Federal Communications Commission
(FCC)
mWARNING! Any changes or modications to this
unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the
equipment.
Class B device:
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur
in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.

12
Optional Accessories
mWARNING! ALWAYS use only authorized Snow Joe®+ Sun Joe®replacement parts and accessories. NEVER use
replacement parts or accessories that are not intended for use with this cordless grass shear +shrubber. Contact
Snow Joe®+ Sun Joe®if you are unsure whether it is safe to use a particular replacement part or accessory with your cordless
grass shear + shrubber. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical
damage.
NOTE: Accessories are subject to change without any obligation on the part of Snow Joe®+ Sun Joe®to provide notice of such
changes. Accessories can be ordered online at snowjoe.com or via phone by contacting the Snow Joe®+ Sun Joe®customer
service center at 1-866-SNOWJOE (1-866-766-9563).
Sun Joe®Replacement Charger for HJ602C
Sun Joe®Replacement Grass
Shear Blade for HJ602C
Sun Joe®Replacement Shrubber
Blade for HJ602C
HJ602C-27
HJ602C-18
HJ602C-17
ModelAccessories Item
1
2
3

13
NOTES

14
NOTES

15
SNOW JOE®+ SUN JOE®CUSTOMER PROMISE
PRODUCT REGISTRATION:
Snow Joe®, LLC (“Snow Joe®+ Sun Joe®”) strongly encourages
you to register your purchase. You can register online at
snowjoe.com/ProductRegistration, or by printing and mailing
in a registration card available online from our website, or
calling our Customer Service Department at 1-866-SNOWJOE
(1-866-766-9563), or by e-mailing us at [email protected].
Failure to register your product purchase will not diminish your
warranty rights. However, registering your purchase will allow
Snow Joe®+ Sun Joe®to better serve you with any of your
customer service needs.
WHO CAN SEEK WARRANTY COVERAGE?
This Warranty is extended by Snow Joe®+ Sun Joe®to the owner
of this Machine (a “Machine” consists of a product powered by
a motor) for residential and personal household use only. This
Warranty does not apply to products used for commercial, rental
or re-sale purposes. Should ownership of this machine change
during the 2-year period, please update the Machine’s owner
information at snowjoe.com/ProductRegistration.
WHAT IS COVERED?
Snow Joe®+ Sun Joe®warrants to the owner that if this Machine
fails within 2 years from the date of purchase due to a defect in
material or workmanship or as a result of normal wear and tear
from ordinary household use, Snow Joe®+ Sun Joe®will send a
replacement part or product, as needed, free of charge and with
free shipping to the original purchaser.
If, in Snow Joe®+ Sun Joe®’s sole discretion, the failed Machine
cannot be repaired with a part, Snow Joe®+ Sun Joe®will elect to
either (A) send a new Machine at no charge and with free shipping
or (B) refund the full purchase price to the owner.
WHAT IS NOT COVERED?
This Warranty does not apply to the Machines that have been used
commercially or in non-household applications. This Warranty
does not cover cosmetic changes that do not aect performance.
This Warranty is only valid if the Machine is used and maintained
in accordance with the instructions, warnings and safeguards
contained in the owner’s manual. Snow Joe®+ Sun Joe®will not
be responsible for the cost of any unauthorized warranty repairs.
This warranty does not cover any cost or expense incurred by
the purchaser in providing substitute equipment or service during
reasonable periods of malfunction or non-use of this product
while waiting for a replacement part or unit under this warranty.
Wearing parts like belts, augers, chains and tines are not covered
under this warranty, and can be purchased at snowjoe.com or
by calling 1-866-SNOWJOE (1-866-766-9563). Batteries are
covered in full for 90-days from the date of purchase.
Repair, replacement or refund of the purchase price are the
exclusive remedies of purchaser and the sole liability of Snow Joe®
+ Sun Joe®under this warranty. No employee or representative
of Snow Joe®+ Sun Joe®is authorized to make any additional
warranty or any modication to this warranty which may be
binding upon Snow Joe®+ Sun Joe®. Accordingly, purchaser
should not rely upon any additional statements made by any
employee or representative of Snow Joe®+ Sun Joe®. In no event,
whether based on contract, indemnity, warranty, tort (including
negligence), strict liability or otherwise, shall Snow Joe®+
Sun Joe®be liable for any special, indirect, incidental, or
consequential damages, including, without limitation, loss of
prot or revenue.
Some states do not allow limits on warranties. In such states, the
above limitations may not apply to you.
Outside the USA, other warranties may apply.
ABOVE ALL ELSE, Snow Joe®+ Sun Joe®are dedicated to you, our customer. We strive to make your experience as pleasant
as possible. Unfortunately, there are times when a product does not work or breaks under normal operating conditions. We
think it’s important that you know what you can expect from us. That’s why we created the Snow Joe®+ Sun Joe®promise.
OUR PROMISE: Snow Joe®+ Sun Joe®warrant new products for two years from the date of purchase. If your product does
not work, or there’s an issue with a specic part, we will x this by either sending you a free replacement part or by sending
you a new or comparable product at no charge. How cool is that! Before you know it, you’ll be back in action cutting,
sawing, mowing, washing and…?

snowjoe.com
mWARNING! This product or its power cord contains chemicals, including lead, known to the State
of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
For more information go to www.P65Warnings.ca.gov.
mWARNING! Some dust created by power sanding, sawing, grinding, drilling, and other construction
activities contains chemicals known [to the State of California] to cause cancer, birth defects, or other
reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specically designed to lter out microscopic particles.
For more information go to www.P65Warnings.ca.gov.