Sunnydaze Decor WAR-840 User manual

Owner’s Manual
WAR-840 Gas Fire Table
WARNING
Improper installation, adjustment, alteration, service or maintenance can cause injury or
property damage. Read the owner’s manual thoroughly before installing or servicing this
equipment. If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
Save these instructions for future use. If you are assembling this unit for someone
else, give this manual to him or her and read and save for the future.
DANGER
WARNING
WARNING
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open ame.
3. If odor continues, keep away from
the appliance and immediately call
your gas supplier or re department.
Do not store or use gasoline or other
ammable vapors and liquids in the
vicinity of this or any other appliance.
An LP-cylinder not connected for use
shall not be stored in the vicinity of
this or any other appliance.
For outdoor use only.
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the
items we sell. Replacement parts or products will be sent at our discretion within the 1-year
warranty period. Proof of purchase, with the date of purchase as well as photos of the
merchandise defect, must be provided. Photos are used to determine the cause of defects and
for future quality control. Register your warranty at www.serenityhealth.com/warranty/
If you have any questions, comments or concerns, feel free to contact us by phone at
888-881-4668, by email: [email protected], or via our contact us page at
www.SerenityHealth.com/contact-us/
Purchase Date: / / Order/Customer Ref. Number:
1

LIMITATION OF WARRANTY AND LIABILITY
NOTICE: Read this Limitation of Warranty and Liability Before Using This
Product. If the Terms Are Not Acceptable, Return the Product at Once,
Unopened, and the Purchase Price Will Be Refunded.
It is impossible to eliminate all risks associated with the use of this product. Such
risks arise from weather conditions, the manner of use or application, or other
unknown factors, all of which are beyond the control of the Seller and Manufacturer.
These risks can cause bodily injury or death, ineffectiveness of the product, and
damage to other property. Seller and Manufacturer do not agree to be an insurer of
these risks you agree to accept these risks.
Seller and Manufacturer warrant that this product is reasonably fit for the purpose
stated in the Owner’s Instructions Manual, subject to the inherent risks described
above, when used in accordance with the Owner’s Instructions Manual under normal
conditions. Seller and Manufacturer provide no other express or implied warranty of
fitness or of merchantability or any other express or implied warranty
In no event shall Seller or Manufacturer be liable for any incidental, consequential, or
special damages resulting from the use or handling of this product. Buyer’s or user’s
bargained-for expectation is for home use of the product in accordance with the
Owner’s Instructions Manual and under normal conditions and that is the exclusive
remedy of the user or buyer and the exclusive liability of Manufacturer or Seller, for
any and all claims, losses, injuries or damages (including claims based on breach of
warranty or contract, negligence, tort or strict liability) resulting from the use or
handling of this product, shall be the return of the purchase price of the product or, at
the election of Manufacturer or Seller, the replacement of the product
Any claim by buyer or user of this product shall be filed within one (1) year of the date
of injury or damage or the claim will be barred. Buyer and user waive any right to file
any class action claim for product defect, design defect, or failure to adequately warn
of product hazards or safe installation.
This Limitation of Warranty and Liability may not be amended by any oral or written
agreement.
2

FOR OUTDOOR USE ONLY !
If you smell gas and/or hear a gas hissing sound:
1. Immediately, SHUT OFF gas to the appliance.
2. Extinguish ALL open flames.
3. If odor continues, keep away from the appliance and immediately call your Gas
Supplier or Fire Department.
DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity
of this unit and or any other appliance.
An LP Gas tank not connected for use shall not be stored in the vicinity of this or
any other appliance.
Improper installation, adjustment, alteration, service or maintenance can cause
injury or damage to property.
Read and understand the Owner’s Manual thoroughly before installing or
servicing this Fire Table / Column.
If the information in this Owner's Manual is NOT followed exactly, a fire or
explosion may result and cause property damage, personal injury or loss of life.
Save this Owner's Manual and these instructions for future use.
If you are assembling this unit for someone else, give this Owner's Manual to them to read.
CARBON MONOXIDE HAZARD.
This appliance can produce carbon monxide which is odorless.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as inside a camper, tent, car
or home.
3

Part A. SAFETY INFORMATION
Before you assemble or operate this unit, please read carefully this entire Owner's Manual.
Failure to do so may result in a fire, explosion, injury or death.
The installation of this unit must adhere to local codes or either the National Fuel
Gas Code, ANSI Z223. 1/NFPA54, OR CAN/CGA-B149.1, National Gas and Propane
Installation Code.
•THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY!
This product shall be used outdoors, in a ventilated space and shall not be used in any enclosed area.
• This unit is to be used with LP Gas / Propane Gas only !
(Propane Gas tank is not attached and not delivered with this unit.
Propane and Gas Tank is sold separately).
• Do not attach a remote gas supply to this unit.
• This unit is NOT intended for Natural Gas.
• Converting this unit to Natural Gas is dangerous and not recommended.
The conversion of this unit shall void the manufacturer warranty.
•Do not use any solid fuel or charcoal for this unit.
• When igniting this unit, exercise caution as some gas pooling from the Burner may cause the flame to
flare that could cause injury.
• LP GAS WARNING : Do not use more than 1/4 inch depth of lava rocks / pumice stones above the burner
holes.
Excessive use of lava rocks / pumice stones, will suffocate the flame.
• If the Propane Gas Tank is leaking gas, you can smell, hear a hiss, or sense a leak at the source.
Do the following:
1. Disconnect the Propane Gas tank.
2. DO NOT attempt to fix the problem yourself.
3. Move yourself and all persons away from the immediate area.
4. Only when everyone is at a safe distance away from the Fire Table / Column, contact your Gas
Supplier or Fire Department for help.
• Applying too much Propane Gas may result in gas pooling and will NOT burn.
Allow fresh air into the unit so that the remaining gas may escape.
•DO NOT use a flame to check for gas leaks.
• The maximum inlet supply pressure: maximum Gas supply 11 inch w.c. (2.74kPa)
• Use LP propane tanks with the following dimensions: diameter 12 in, height 18 in - capacity 20lbs.
•
You must use a Propane Gas Tank that has a colla
4
r to protect the Gas Valve.
4

• DO NOT fill tank over 80% full.
• The tank system must be set up for vapor withdrawal.
• STOP using if any part of the Propane Gas Tank is damaged.
Rust and dents in tank may be hazardous and should be inspected by a Gas Supplier.
• DO NOT burn anything other than the provided materials for this Fire Table.
• Keep away from the unit for the first 20 minutes after igniting your unit for the first time, as lava rocks /
pumice stones could pop out and cause injury.
Should any rocks pop out, discard them.
• Always ensure that lava rocks / pumice stones are completely dry before use.
Failure to do so will cause them to crack or pop.
• DO NOT operate unit until all parts are fully assembled.
• DO NOT paint or color any part of this Fire Table / Column.
• Unit may be hot while in use, DO NOT attempt to move it while in use.
• Never leave this Fire Table / Column unattended while in use.
• This unit is NOT intended for cooking.
• Keep all flammable items away and DO NOT use any other fireplace cover for this unit.
• Keep a safe distance to avoid burning skin or clothing.
• DO NOT sit or rest hands or feet on this Fire Table / Column.
• Never place hands or fingers onto upper portion of this unit while in use.
• Keep all electrical cords and fuel supply hose away from heated surfaces.
• Combustible material should NOT be within 72 inches of the top of the unit, and within 48 inches around
the entire unit.
5

• Keep the appliance area clear and free from combustible material, gasoline and other flammable vapors
and liquids.
• If the flame goes out while burning, turn the gas valve off.
Wait 5 minutes before repeating the initial lighting procedure.
Once you have a flame started, hold down the control knob for 1 minute.
• DO NOT add water into the unit.
• DO NOT operate unit if any part has been under water.
Immediately call for a Qualified Service Technician to inspect the appliance.
Where necessary, secure Qualified Service Technician to replace part(s) of the Control System and any
gas control parts that has been under water.
•DO NOT disconnect any part while the unit is in use.
• DO NOT store a spare Propane Gas Tank on or near this unit.
• If the Fire Table / Column is placed indoors for storage, detach the Propane GasTank and leave the tank
outdoors.
This unit is for outdoors use ONLY.
• DO NOT operate on a boat or vehicle.
This unit can only be used on any stationary outdoor flat surface ONLY
• Always remove protective cover before operating (where applicable) and / or use of your Fire Table /
Column.
• DO NOT set the Protective Cover (E) over the unit until the Fire Table / Column is turned off and
completely cooled down (where applicable).
• Check for leaks after not using the unit for long periods of time.
• Children must never operate this Fire Table / Column.
Children must be supervised AT ALL TIMES while near this Fire Table / Column.
• The maximum gas supply pressure is 250psi.
• All installation and repair should be done by a Qualified Service Technician.
This unit should be inspected annually and cleaned regularly.
• Inspect all elements of this Fire Table / Column before each use.
If there is damage, the Burner must be replaced.
• Be aware of the hazards of high temperatures and stay away from the unit to avoid any burns or injury.
• The gas supply tank should be constructed and marked with the specifications for the LP Gas tanks of
the U.S. Department of Transportation or the National Standard of Canada CAN/CSA-B339, LP Gas tanks,
spheres and tubes for Transportation of Dangerous Goods and Commission.
•The LP Gas tank must have a listed overfilling prevention device and a QCCI or Type I, LP Gas tank
connection.
• This heating appliance should NOT be used on plastic, artificial wood desks or any desk.
6

• Children and adults should be alerted to the hazards of high surface temperatures and should stay away
to avoid burns or clothing ignition.
• Young children MUST BE carefully supervised at all times when they are in the area of this appliance.
• Clothing or other flammable materials shall NOT be hung from the appliance or placed on or near the
appliance.
• Any guard or other protective device removed for servicing the appliance shall be replaced prior to
operating and use of this appliance.
• Installation and repair(s) should be done by a Qualified Service Technician.
The appliance should be inspected before use. If you suspect there are issues, contact a Qualified
Service person.
More frequent cleaning may be required as necessary.
It is imperative that the control compartment, burners and circulating airways of the appliance are kept
clean.
When APPLICABLE:
• Keep gas tank at least 5 feet away from unit when lit (if external tank).
•Allow Fire Burner / Column to cool down completely before placing on lid.
• Keep the hose away from any pathways to eliminate any accidental damage (if external tank).
• DO NOT use Fire Table / Column while lid is installed.
Always remove the lid while Fire Table / Column is in use.
Use only the Regulator (12/19) and Hose( 12) assembly provided with this unit.
Replacement parts must be supplied directly by manufacturer.
Inspect the Burner (08 ) before use of this unit.
If the Burner (08) shows any kind of damage, DO NOT operate the appliance.
NOTE: You must follow all steps to properly assemble this Fire Table / Column.
Make sure the Gas Valve is turned “OFF” before assembling.
DO NOT attempt to assemble without proper tools.
7

Parts Diagram
Item Picture Description Qty
01 Guard 1
02 Thermocouple
04
Ignition Pin
05
Main Frame of
Fire Table
07
Lava Rocks 1
08
Burner 1
09
Nozzle 1
10
Corrugated Pipe 1
11
Switching Valve 1
12
Regulator Valve
with Gas Hose 1
13
Control Knob 1
Ignitor 1
Foot 4
Tabulated here below are the description to all parts as shown in above Picture .
03
1
1
1
06
8

Parts List
Item Picture Description Qty
A1
B
AA Battery
1
CPanel C2
DPanel D 1
Protective Cover
1
FPanel F
1
G
H
Table Top
4
Foot
6
Bolt (M6*40MM)
4
6
12
Hardware
Item Picture Description Qty
6
M6 Washer
Hex Bolt Driver
1
Bolt (M6*35MM)
Bolt (M6*15MM)
8
8
:
7
A
B
G
H
F
CD
9

B
Assembly Instructions
Step 1:
Attach panel (D) and the panel (F) to the
table top (G) by using 4pcs of Bolts (S001)
and 4pcs M6 washer (W001) with Hex Bolt
Driver (T001). Please do not fully tighten.
Step 2:
Attach panel (C) with Panel (D) and Panel
(F) together by using 8pcs Bolts (S002)
and 8pcs M6 washer (W001) with Hex
Bolt Driver (T001). Please do not fully
tighten.
D
F
G
D
F
C
10

Step 3:
Attach adjust foot (H) to the bottom of fire
pit using 8pcs of Bolts (S003) with Hex Bolt
Driver (T001). And tighten the Bolts.
Step 4:
Then tighten all the bolts.
Assembly Instructions
11

Step 1:
1. Check that the Contro Knob for the
gas supply system is turned to the "OFF''
position before starting any assembly.
2. Place a 20 lb Propane Gas Tank (not
included) into a secure position.
Step 2:
Turn the Cylinder Valve on the tank in a
clockwise direction to TURN OFF SUPPLEY of
the LP Gas supply-Attach the preassembled
Regulator (19) from the Fire Table to the
Cylinder Valve (21) by turning the Black
Regulator Coupling Nut clockwise.
Make sure it is fastened securely and tighten
connections-by HAND only.
User's Instructions
12

Step 4:
Put Lava Rocks over the Burner Ring.
Warning: DO NOT PLACE LAVA ROCKS ON
THE GUARD. KEEP GUARD CLEAN.
To ensure proper function, the Guard (01)
on the Burner (06) should never have lava
rocks (05) covered over it.
User's Instructions
Step 3:
Remove the Electronic Igniter Cap on the
Eectronic Igniter by unsecrewing and
slide the Battery (B) into the battery slot.
Make sure the positive side of the Battery
faces outwards. Screw the Electronic
Igniter Cap over the battery, tightly.
13

MAINTENANCE
•Before performing any maintenance always disconnect propane gas tank.
•Keep the heating item free and clear from combustible materials.
•Visually inspect burner for obstructions and keep tank enclosure free and clear from debris.
•Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner and lava rocks
are completely cooled down. Wipe down with a soft cloth.
•Harsh weather conditions may cause stubborn stains, discoloration and possibly rust pitting.
•Permanent damage may occur if powder or solvent comes in contact with painted or plastic
components on this heating unit.
•Keep the heating unit stored away from direct sunlight.
•If storing this unit inside, disconnect the propane gas tank from the gas valve.
•Not using manufacturer approved or supplied parts/accessories may result in a defective condition
and void the warranty of this heating unit.
•Always place lid (if applicable) or protective cover on heating item when not in use.
MGO Surface Care
Our MGO material has been sealed with a special treatment to prevent staining and moisture
absorption, but it does require proper maintenance to ensure the integrity of the surface. Please
see below for recommendations on maintaining your MGO surface for years of pleasure:
•Clean any spills immediately to prevent permanent MGO surface staining or damage.
Blot any liquid spills with a clean, dry cloth to avoid spreading of the spill to the rest of the table.
Clean your product surface with a soft, clean cloth or sponge. Mix a solution of warm clean water
and mild dish soap to remove any surface dirt or mild spills. Rinse all soap solution off of the
tabletop and dry completely to avoid water spots. Regularly cleaning the surface will aid in a
longer lasting product.
• Do not use pet oleum-based or abrasive cleaning products. Do not use any harsh brushes when
cleaning the surface.
•Do not slide products across the surface to avoid permanent scratching and damage.
•Always use protective mats such as coasters or placemats when eating on an MGO surface.
These protective products will help absorb sweating on cool beverages and will block out any
heat rings from appearing beneath a warm mug or plate. When placing hot dishes on MGO
surface, always use mats or hot pads.
•MGO surface must be covered at all times when not in use. Cover your product with an
outdoor furniture cover when not in use to protect it from the elements. Store your product
indoors during winter months. Avoiding extreme cold temperatures will prevent cracking of the
tabletop.
14

Problem: Burner will not light using igniter
Please review the Helpful Tips on page 15 for common fixes to this problem.
Possible Cause 1: Electrode and burners are wet.
-Please contact Net Health Shops,LLC to request the parts.
-Wipe dry with cloth.
Possible Cause 2: Igniter battery is dead or backwards.
-Check that the AAA battery is inserted correctly in the igniter (see bellow photo) or
replace the battery. Make sure the plastic wrap on the battery has been removed.
Possible Cause 3: Igniter P i n cracked or broken - sparks a crack.
Possible Cause 1: No Gas Flow
-Check if the LP gas tank is empty. If empty, replace and refill. If the propane tank is not empty,
refer to Problem: Sudden drop in gas flow on the following page.
Possible Cause 2: Coupling nut and regulator not fully connected.
Possible Cause 3: Obstruction of gas flow.
Possible Cause 4: Spider webs or insect nest in the venturi.
- Clean the venturi.
Possible Cause 5: Burner ports clogged or blocked.
-Reference Problem: Irregular flame pattern on the following page.
Clean the burner ports as described there.
Problem: Burner will not light with match
Problem: The fire table emits a lot of black smoke when in use
Possible Cause 1: Hose from gas fire table is pinched.
-Make sure the hose is not pinched between the fire table and
the source of the gas.
Troubleshooting
-Turn the coupling nut about one half to three fourths a turn, until y ou feel a solid stop.
Do not use tools, tighten by hand only.
Venturi
- Check for bent or kinked hose.
Possible Cause 4: Residue on Igniter Pin.
-Check for residue on the igniter pin or Thermocouple.
If dirty,thoroughly clean the area.
AB
-Check that the electronic Ignitor Cap (B) is tightly fitted to
the spring(A).If loose,please adjust the spring accordingly.
15

Problem: Sudden drop in gas flow, or a reduced flame height
Possible Cause 1: Out of Gas.
-Check for gas in the LP gas tank.
Possible Cause 2: Excess flow safety device may have been activated.
-Turn control knob to OFF, wait 30 seconds and light outdoor fire table.
if flames are still too low, reset the excessive flow safety device by turning off the control knob and LP
gas tank valve. Disconnect regulator. Turn burner control knob to HIGH. Wait at least 5 minutes.
Turn burner control knob off. Reconnect regulator and perform a leak check at tank connection. Turn
LP gas tank valve on slowly, wait 30 seconds and then light outdoor fire table.
Problem: Irregular flame pattern, flame does not run the full length of the burner
Possible Cause: Burner ports are clogged or blocked.
-Clean burner ports. Do this by inserting a paperclip into
each of the burner ports to ensure they are not clogged.
WARNING: Make sure burner is not on, and has had
sufficient time to cool before touching it.
Problem: Flame blow out
Possible Cause 1: High or gusting winds.
-Increase flame to HIGH setting.
Possible Cause 2: Low on LP gas.
-Replace or refill LP gas tank.
Possible Cause 3: Excess flow valve tripped.
-Refer to Problem: Sudden drop in gas flow
Problem: Flame seems to lose heat when burning in cold weather -
temperature below 50°F
Possible Cause 1: Ice has built up on the outside of the LP gas tank because the
vaporization process is too low.
-Turn the control knob and the LP gas tank to OFF. Replace with a spare LP gas tank and
resume burning. Store the spare LP gas tank in a well ventilated area, away from children.
Possible Cause 2: Flame is being obstructed at burner ports.
Possible Cause 3: Mixing chamber of the burn tube is blocked or obstructed.
-Make sure that the gas ports on the burner are free of any lava
rocks/fire glass so that the flame can flow naturally.
-Clear out the mixing chamber located before the Venturi.
16

HOW TO REPLACE THE
THERMOCOUPLE ON A
30,000-50,000 BTU FIRE TABLE
1. The thermocouple will be
under the Pilot Guard on the top
of the unit.
Please remove the Pilot guard by
unscrewing it from the metal bowl
with a screw driver.
2. Once the Pilot Guard has been
removed, you will have two
components exposed; the copper one is
your thermocouple. Please unscrew the
nut holding the thermocouple in place.
THERMOCOUPLE
IGNITION
PIN
PILOT GUARD
1.
THERMOCOUPLE IGNITION
PIN
2.
2.
3. Inside the unit, you will notice that the end of the thermocouple line is
directly screwed in to the gas valve. Please unscrew the thermocouple from
the back end of the gas valve. Do not take off the valve’s silver backing, only
unscrew the small nut as shown above.
Once the thermocouple is unscrewed, please remove it from the top of the unit.
Feed the new one through the top of the unit towards the bottom and ensure
that the nuts are screwed the top and bottom to hold it in place.
4. Screw the end of the thermocouple to the back end of the gas valve with the
silver backing.
3. 4.
Once this has been done, please test the unit.
You may have to reset the gas valve once again as the safety mechanism
may have been set off by the new components introduced:
Resetting Your Gas Valve
Completely detach the propane tank from the table. Do not forget to turn
the propane tank valve down. Turn the heat setting knob to high and leave
it on that setting for about two to three minutes. Once you have done this,
please turn the knob back to off. Hook up the propane tank and turn the
propane tank’s valve a quarter of a turn at a time.
NOTE: When reattaching the propane tank, please turn the valve to release
the gas back in to the unit VERY SLOWLY. We want the unit to register gas
coming through but not too much at once, this will flood the unit and you
will have to start all over!
This is so that the gas valve can register the gas coming through a little at a
time. Once you have turned the gas on all the way please go ahead and try
to light the table again. This should reset your fire table’s safety mechanism
Problem: Burner JUST LIGHT UP FOR SECOND AND WILL AUTOMATICALLY TURN OFF
17