Sunricher SR-GW-TDA User manual

DIN Rail Ethernet (IP) DALI Gateway
Input
Voltage
Output
Voltage
24VDC 250mA max
12-22.5VDC
Output
Current
Important: Read All Instructions Prior to Installation
Size(LxWxH)
110x53x65mm
Product Data
Wiring Diagram
Ambient
Temperature
-20℃ ~ +50℃
Number of
DALI Channel
1
While built-in DALI PS enabled
Input
Voltage
24VDC Max. 2mA
DALI Current
Consumption Size(LxWxH)
110x53x65mm
Ambient
Temperature
-20℃ ~ +50℃
Number of
DALI Channel
1
While built-in DALI PS disabled
• Supports DT6, DT8 Tc, DT8 XY, DT8 RGBWAF device types
• No need for DALI master controller，supports up to 64 , grouping and scene settingsdevices’ addressing
• Easy connect to a network through Ethernet connection
• Easy & quick configuration through the mobile application
• Built-in 250mA DALI PS, no extra wiring required
• Waterproof grade: IP20
• Supports cycle schedule configuration
• Built-in battery, built-in RTC, supports timer task configuration
• 5 years warranty
1) While built-in DALI PS enabled
Note: When built-in DALI Bus PS is enabled, a DALI gateway can supports up to 64 control gears.
• DO NOT expose the device to moisture.
• DO NOT install with power applied to device.
Safety & Warnings
Function introduction
DALI Output/Input
DALI Gateway
1
Disabled
Enabled
21
24VDC Input
Enable or disable to
use built-in DALI PS
by dial switches:
2
Power indicator Prog. indicator：It turns to blue
during reset
12345678
DALI DT6 Control Gear
DA
DA
DALI DT6 Control Gear
DA
DA
DALI DT8 Control Gear
DA
DA
L
N
G
V -
V+
OUTPUT
INPUT
24V
CV PSU
LNG
Router
21
Reset Key: Long press it to help withdraw
the device from Internet/APP.
DALI Gateway DALI Gateway
21
RJ45 Terminal

2) While built-in DALI PS disabled
Note: When built-in DALI Bus PS is disabled, the number of following control gears depends on external
DALI PS.
Operation
1) Do wiring according to the wiring diagram and power on the DALI system.
Step 1: Download the APP (searching “Light+space” from App Store and Google Play) and set up an account.
Then open the APP and add the gateway to the network.
2) Pair the DALI gateway to the network and control it through the APP:
Download “Light+space ”
Note: 1. Please make sure the following DALI devices is connected with the gateway.
2. Creat an area before adding gateway.
3. Make sure that the WIFI network of mobile phone is in the same network as DALI gateway.
Step 2: Power on the gateway and add it manually, the gateway will be found.
Step 3: The gateway was added successfully, then select the gateway to configure the following DALI devices.
DALI DT6 Control Gear
DA
DA
DALI DT6 Control Gear
DA
DA
DALI DT8 Control Gear
DA
DA
L
N
G
V -
V+
OUTPUT
INPUT
24V
CV PSU
LNG
Router
2
1
L
N
G
DA
DA
OUTPUT
INPUT
DALI BUS
POWER SUPPLY
DALI Gateway DALI Gateway
Working with “Light+space” APP
Tap “Gateway”
Tap “+” to add
DALI Gateway
Gateway shows in
“Test” area
Tap “Add
subdevice” to
configure following
DALI devices
2
1
Tap “LED
already blink”
enter search
device interface

Step 4: All devices have been found, then add it to a certain area, and click the device name into control page.
Step 5: Add new group for those devices,add new scene settings for certain groups or devices.
Step 6: Schedule setting, you can add schedules to listing devices. It can be set from Monday to Sunday
Step 7: Task setting, you can add tasks with any devices or groups, and run previous scene settings
Step 8: Monitor interface, where you can view the status and power consumption chart of the devices.
You can add tasks
to any devices You can add tasks
to any groups
Device online Device offline
Tap here,enter
editing control page
Tap here,remove
DALI gateway
Note: 1. If the light control interface cannot be opened, please search and add devices again in DALI gateway interface.
2. For more information please refer “ ”.
Step 9. Remove the gateway or DALI devices from the APP interface.
Remove device
Group control Bring up scene
Light+space User manual

110.00 mm
65.00 mm
Product Dimension
53.00 mm
Note：Subject to change without notice. Please contact us if you have any questions.
Update log
Date Version Update content Update by
2021-10-21 V1.0 Original version Romeo
Tap here,enter
editing control page
Tap here,remove
DALI gateway
Note: 1. If the light control interface cannot be opened, please search and add devices again in DALI gateway interface.
2. For more information please refer “ ”.
Step 10. Remove the gateway or DALI devices from the APP interface.
Remove device
Tuya Smart User manual
OTA Instruction
You can update the latest firmware manually.