Sunricher ZG2801K2-5C User manual

RGB CCT DIM 3 in 1 Zigbee Remote Controller
09.ZGK4D.04837
Function introduction
Important: Read All Instructions Prior to Installation
Product Data
Protocol
Input Voltage
Transmission Frequency
Transmission Range (free field)
Protection Type
Dimming Range
Dimensions
ZigBee 3.0
3VDC (CR2430)
2.4GHz
30m
IP20
0.1%-100%
86x86x14mm
• DO NOT install with power applied to the device.
• DO NOT expose the device to moisture.
Safety & Warnings
Operation
10.10 mm
Front side
Back side
Battery: CR2430
Before the first use, please open the battery
cover and remove the protective film
The remote control can be fixed on the wall with 3M glue or screw.
ON/OFF button, click to turn
on/off the bind lighting devices
CCT button, click to get 2700
Kelvin directly, press and hold
to increase cool white, release
and press and hold again to
increase warm white.
Brightness down button, press
and hold down to increase light
intensity, release and press
and hold down again to
decrease light intensity
RGB color button, press and
hold down to get the color you
would like
Note: This remote supports
1 group for binding max. 30
lighting devices.
• ZigBee RGB+CCT+DIM remote based on ZigBee 3.0
• Enables to control both RGB and CCT lighting devices
• Battery powered remote with low power consumption
• Enables to pair ZigBee lighting devices via touchlink commissioning without coordinator
• Supports find and bind mode to pair with ZigBee lighting devices
• Supports 1 group for binding max. 30 lighting devices
• 2.4 GHz global operation
• Transmission range up to 30m
• Compatible with universal ZigBee Gateway products
• Enables to bind and control universal DIM, CCT, RGB, RGBW and RGB+CCT zigbee lighting devices
1.This ZigBee RGB+CCT remote is a wireless transmitter that communicates with a variety of ZigBee
compatible systems. This transmitter sends wireless radio signals that are used to remotely control a
compatible system.
2.This ZigBee remote supports 1 group for binding lighting devices and enables to control RGB and
CCT ZigBee lighting devices.
ZigBee Clusters Supported by This Remote Are As Follows:
Input clusters:
• Basic • Power Configuration • Identify • Diagnostics
Output clusters:
• Identify • On/off • Level control • Ota • Color control

3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
5. Removed from a Zigbee Network through Coordinator or Hub Interface
6. Factory Reset Manually
Note: 1) After pairing successfully, the remote information will appear on the controller or hub interface.
2) No remote information will appear on the hub interface if pairing to Philips Hue Bridge.
4. TouchLink to a Zigbee Lighting Device
Note: 1) Directly TouchLink (both not added to a ZigBee network), each remote can link with 30 devices.
2) TouchLink after both added to a ZigBee network, each remote can link with max. 30 devices.
3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.
4) After TouchLink, the remote can control the linked lighting devices.
7. Remove a Touchlink Paired ZigBee Lighting Device
8. Factory Reset a Lighting Device (Touch Reset)
Note: the device shall be added to a network, the remote added to the same one or not added to any network.
Step 1: Remove the remote from
previous zigbee network if it has already
been added to it, otherwise pairing will
fail. Please refer to the part "Factory
Reset Manually".
Step 2: From your zigbee
controller or hub interface,
choose to add device or
accessory and enter
Pairing mode as instructed
by the controller.
Step 3: Press and hold
down until LED indicator
turns on.
Step 4: Immediately short press to
search nearby network, indicator
flashes every 1 second, 20 seconds
timeout if there is no network. Indicator
will then blink 5 times quickly for
successful pairing.
From your ZigBee controller or hub
interface, choose to delete or reset
the remote as instructed, indicator
flashes 3 times quickly to indicate
successful removing.
Step 1: Set the Touchlink
paired zigbee device to
start TouchLink
commissioning, please
refer to its manual to learn
how.
Step 2: Bring the remote within 10cm of
the lighting device.
Step 3: Press and hold
down until LED indicator
turns on.
Step 4: Immediately short press twice to
start TouchLink removing of the remote.
LED indicator flashes fast for 3S, then
flash 6 times slowly to indicate
successful removing.
Step 1: Set the zigbee
lighting device to start
TouchLink commissioning,
please refer to its manual
to learn how.
Step 2: Bring the remote within 10cm of
the lighting device.
Step 3: Press and hold
down until LED indicator
turns on.
Step 4:Immediately short press to start
TouchLink commissioning of the remote.
LED indicator flashes fast for 3S, then
flash 6 times slowly to indicate successful
pairing to the device and the light
connected to the device will blink twice.
Step 2: Immediately short press 5 times
continuously, indicator flashes 3 times
quickly to indicate successful reset.
Step 1: Press and hold
down until LED indicator
turns on.
Note: All configuration parameters
will be reset after the remote is reset
or removed from the network.
Step 1: Set the zigbee
device to start TouchLink
commissioning, refer to its
manual.
Step 2: Bring the remote within 10cm of
the lighting device.
Step 3: Press and hold
down until LED indicator
turns on.
Step 4:Immediately short press 5 times to
start Touch Reset of the remote. LED
indicator flashes fast for 3S, then flash 3
times slowly to indicate successful reset.
ZigBee Lighting Device
< 10cm
ZigBee Lighting Device
< 10cm
ZigBee Lighting Device
< 10cm

9. Find and Bind a Zigbee Lighting Device
10. Find and Unbind a Zigbee Lighting Device
11. Clear All Find and Bind Mode Paired Lighting Devices
12. Setup a Network & Add Devices to the Network (No Coordinator or Hub Required)
Step 5: Add more remotes to the network as you would like.
Step 6: Factory reset the lighting devices that you would like to add to the network, refer to their manuals.
Step 7: Touchlink to pair the added remotes and lighting devices you would like to add, the devices will be added
to the network through Touchlink, refer to their manuals.
15. Battery Power Monitor Function
The remote will report battery power value to the coordinator under following situations:
• When powered on.
• When short pressing both and buttons simultaneously.
• When operating the switch to send data packets (over 4 hours since last operation).
• When added to the network by a coordinator.
14. How to Check Whether the Remote Belongs to a Network or not
.
Click any button, indicator blinking means the remote has already been added to a network. No blinking of indicator
means the remote does not belong to any network
Step 2:Press and hold down
until LED indicator turns on.
Step 3:Short press to enable the
remote (target node) to find and
bind initiator. LED indicator flashes
4 times for successful binding or
twice if binding fails.
Note: Each remote can bind
max. 30 lighting devices.
Step 2:Press and hold down
until LED indicator turns on.
Step 3:Short press twice to
enable the remote (target node)
to find and unbind initiator. LED
indicator flashes 4 times for
successful unbinding or twice if
unbinding fails.
Step 2:Press and hold down
until LED indicator turns on.
Step 3:Short press 5 times
continuously to clear all bound
lighting devices with this
group. LED indicator flashes 4
Step 1: Factory reset the
remote and the lighting
device, refer to their
manuals.
Step 2: TouchLink the
remote and device to setup
a network, refer to their
manuals.
Step 3: Short press to
enable the network to
discover and add devices,
LED indicator will flash
twice. 180 seconds timeout,
repeat the operation.
Step 4:Set another remote into network
pairing mode and pair it to the network,
refer to its manual.
Note: Make sure the device and remote already added to the same zigbee network.
13. OTA
The remote supports firmware updating through OTA, and will acquire new firmware from zigbee controller or
hub every 10 minutes automatically.
ZigBee Lighting Device
Step 1: Start find and bind mode on
the Zigbee lighting device (initiator
node) and enable it to find and bind
target, refer to its manual.
ZigBee Lighting Device
Step 1: Start find and bind mode on
the Zigbee lighting device (initiator
node) and enable it to find and
unbind target, refer to its manual.
ZigBee Lighting Device
< 10cm