Sunshine GA158 User manual
GA158
Clock/Weather Station Assembly Instructions
12
1
2
3
4
6
8
9
10
11
IMPORTANT! PLEASE READ
All Sunshine
garden clocks and weather stations are prepared with a powder coated/
painted nish. The nish will weather over time, depending upon the environmental
conditions where the product is installed. Your proper care of the clock/weather station
(see below) will enhance both its life and appearance. Post treatments, such as clear
lacquer, are not recommended.
PROPER CARE
In order to maximize the appearance of a Sunshine garden clock/weather station, it is
important that dust and debris is removed from its surface periodically. It is recom-
mended that the clock/weather station be wiped down weekly using a soft, dry cloth.
DO NOT
use any abrasives such as car wax or other polishes, glass cleaners or chemi-
cals, as this will scratch/remove/damage the protective coating. All Sunshine clocks/
weather stations receive a durable powder coat nish, which enhances their durabil-
ity. The nish should also be wiped down weekly with a soft, dry cloth to
remove dust and debris that will accumulate on the surface.
FAILURE TO FOLLOW THE ABOVE CARE INSTRUCTIONS WILL INVALIDATE
YOUR PRODUCT GUARANTEE.
REPLACEMENT PARTS
For information regarding replacement parts, please contact your retailer.
GUARANTEE
All Sunshine
garden clocks and weather stations are guaranteed against defects in
material and workmanship for a period of ONE YEAR from the date of purchase.
IMPORTANT:
This guarantee does not cover damage or failure resulting from ac-
cident, misuse or abuse, lack of reasonable care (see above), vandalism, and acts of
nature such as lightning damage. No responsibility is assumed for any special inciden-
tal or consequential damages. Damage occuring during transit is not covered by this
guarantee. Any claims under this guarantee should be referred in the rst instance to
your retailer.
TECHNICAL SUPPORT
For advice on installation or technical queries, please contact our Customer Service
Helpline on 0845 456 5111, 9 am - 5 pm Monday to Friday.
Distributed by:
Sunshine Lifestyle Products, Ltd
Unit 9, Oxonian Park
Langford Locks, Kidlington
Oxfordshire, OX5 1FP
GA158 November 2005
Printed In China
Step 1a
Small bracket A (1)
Clock Assembly (J)
Upright (4)
Small bracket B (1)
Upright
Connection
Upright
Connection
Upright
Disc (I)
Top (1)
Allen Screw
A (8)
Large bracket B (1)
Parts Included:
Centre
Disk (1)
Assembly Time:
Usage:
Allen Screw
B (4)
Large bracket A (1)
When using this weather station outside, place unit in shaded area away from direct sunlight for
most accurate reading of gauges, as direct sunlight may cause some
deviation in gauge readings.
Assembly:
Adjustment:
1) Remove round plastic cap to expose adjustment dial. To adjust the Clock reading, turn adjust-
ment dial to adjust needle on the face of the unit.
2) Temperature gauge is self-adjusting.
3) Replacing Battery: On back of clock, remove round plastic cap by pulling metal ring. Insert
battery matching the “–” and “+” markings as indicated on the inside of the battery housing, to
the markings located on the battery, and re-attach round plastic cap. Requires 1 “AA” Battery
(Included).
Time:
20-30 minutes
Step 1b
Step 2
Plastic Cap
Battery
1)
Screw Large Bracket
A in between two of
the uprights. Then
Screw Large Bracket B
between the remaining
two uprights. Now t
the downward notch on
Bracket B into the up-
ward notch on Bracket A
by placing the uprights
at an angle to each other,
until the notches line up.
Tighten with Allen Key.
2)
Now Screw in the Small Bracket A into the uprights then t
Small Bracket B into the notch in Small Bracket A and screw it
into the remaining uprights. Then tighten them with Allen Key.
12
1
2
3
4
6
8
9
10
11
MADE IN CHINA
- AA 1.5V +
Adjustment
knob for
clock
M4 Allen
Wrench
(1)
Foot Tab
(4)
1/8 Allen
Wrench (1)
Allthread
Sleeve (1)
Allthread
(1)
Stake (4)
1/8 Allen
Key
3) Place the Upright Connection Disc on top
of the uprights and screw it on to the tops of
the uprights.
Assembly Cont.:
Step 3
4)
Slide the upper part of the clock as-
sembly through the Upright Connection
Disc. Now screw the top onto the clock
assembly securing it to the Upright Con-
nection Disc.
Step 4
5) Screw Centre Disc Allthread into the
hole in the top of Large bracket B. Slide
Allthread Sleeve over Allthread, then
Screw the Centre Disc onto Allthread
above sleeve until secure.
Step 5
12
1
2
3
4
6
8
9
10
11
6) Thread foot tabs into the four holes
under uprights. Adjust height as necessary
levelling xture for uneven surfaces.
M4 Allen Key
Other Sunshine Clock manuals
