Sunsky G2 User manual

GPS Speed meter: G2
Warning:
This product working voltage is 5V, and it is forbidden to use a voltage higher than 5V for
power supply.
Display functions:
1. Satellite icon: After the satellite is found, it stops flashing and goes out before it can be
used normally. N-North S-South W-West E-East
2. Atmosphere light: Right press the wave button to turn off, again to turn on
3.Multi-function display: vehicle speed, time, vehicle speed + time, number of satellites,
travel distance, travel time (Short press the wave button vertically to change the function)
4. Atmosphere light: Right press the wave button to turn off, again to turn on
5. Multi-function display unit: TRIP mileage,TIM clock, MPH miles ,KM/H kilometers

Wave button function
1.Short press in: Switch to vehicle speed , Time, Vehicle speed + time, Number of
satellites ,Travel distance ,Travel time
2.Long press in: Enter the setting, after adjusting, press vertically for 2 seconds to save and
exit
3.Push left: Switch to standard mode or concise mode
4.Long push left: Push left for 2 seconds to turn off the buzzer alarm, do it again to turn on
5.Push right: Switch to concise mode or standard mode (move option after entering setting)
Enter setting mode:
Long press in to enter into the setting mode, press right to choose the menu, and short press
in to confirm. Once finishing the setting, long press in 2 seconds to save and exit.
Menu
Function
Parameters
Adjustment
range
Explanation
Default
value
Parameter value
interface
Speed
50-150
Adjust the parameter
value when there is an
error between HUD and
dashboard.
Ex: dashboard displays
100 KM/H, HUD displays
105 KM/H. Please adjust
the parameter value to
102.
107

Over speed
alarm
0-250
When the vehicle speed
reach to 150, HUD will
give the alarm
150
Fatigue
driving alarm
1.0-8.0
HUD will give fatigue
driving alarm each 4
hours
4.0
Brightness
adjustment
0-11
0=automatic sensitivity
adjustment
1-11=manual adjustment
1=darkest, 11=brightest
1→11 is increasing
0
Speed unit
0-1
0=KM/H (kilometers)
1=MPH (miles)
0
Time
adjustment
0:00-12:00
Adjust the time zone
when the satellite is not
received, the default is
East 8 zone. Only need
to calibrate the local time
after searching the
satellite
0
Factory
reset
0-1
Default=0,
→1, long press in for 3
seconds to save and exit
0

Troubleshooting
1.The screen without any display, and no power
Check whether the USB cable is damaged, replace the USB cable for testing, and prohibit
the use of voltage higher than 5V for power supply
2.Without Car Speed
After HUD power-on, the satellite icon flashes will start to look for the satellite. Please driving
the car to the open road. It will work after it stops flashing
3.Time calibration
3.When the satellite icon flashes and no satellite is received, enter item 6 of the setting item
to adjust the local time zone. The default is East Zone 8.
After the satellite icon flashes and the satellite is found, enter item 6 of the setting item to
adjust and calibrate the local time.
4.Inaccurate Speed
a.First check the speed unit is correct or not, the speed unit including KM/H and MPH,
(please refer to the setting mode to switch the unit).
b.The car manufacturers usually make the dashboard speed 5-7% higher than the ECU. The
international standard is based on satellite data.
(if the dashboard shows 100, and the device shows the 105, change the default value at
102)
5.Driving direction display error
Satellites cannot tell where you are driving when there is no speed. After the vehicle speed
exceeds 5KM / H, the direction can be displayed normally.
6.Speed is still displayed after the car stops
Under the underground parking lot, tunnel, under the overpass, there will be unstable
satellite drift when there is obstruction.
7.Turn off the buzzer
Push left for 2 seconds to turn off the buzzer, do it again to turn on.