Sunvision Scientific SV101 IGUANA Assembly instructions

Sunvision Scientific Inc.
SV101 IGUANA Active Surveillance
System
Hardware Installation Manual
Version 1.25
Sep. 2006
Revision History
Date Version Remark
2006/4 1.2
2006/9 1.25 PAL
2007/02/27 2.0 System requirements and setup
1

Sunvision Scientific Inc.
1SYSTEM CONFIGURATION DIAGRAM.....................................................3
2SYSTEM REQUIREMENTS AND SETUP....................................................4
3SV101 COMPONENTS .........................................................................6
3.1 SV1018 IGUANA Active Surveillance module.............................8
3.2 SV1010 MPEG4 real time hardware compression video card..13
3.3 Watchdog reset cable setup......................................................17
4SV1010 PC END CONNECTOR...........................................................18
4.1 SV1010 PC end connector Introduction....................................18
4.2 SV1010 PC Side Connector Connection...................................19
4.3 RJ45 connector PIN definition...................................................20
5SV1015 RELAY I/O CONTROL BOARD .................................................21
6CAMERA SETUP STEPS ......................................................................22
7CAMERA MODULE INSTALLATION TIPS................................................26
7.1 Introduction................................................................................26
7.2 The Camera Module Installation Guidelines .............................26
7.3 Where to Install the Camera Module.........................................28
2

Sunvision Scientific Inc.
1 System Configuration Diagram
SV101 IGUANA Active Surveillance System
3

Sunvision Scientific Inc.
2 System requirements and setup
Recommended specifications of computer
zCPU
zRAM
zIndividual VGA Card
zSATA HD Control
Card
zVGA Card Slot
zHard disc
zOperation System
Intel PD or Core 2 Dual (or above)
1GB or more of DDR (DDR II ) RAM
AGP x 8 Interface or PCI-E x 16 Interface
PCI-E Interface or PCI-X Interface
PCI Interface or PCI-X Interface
120GB x1 + 250GB or more x1
Windows XP Home Edition or Professional
zNote 1: There could be bias oblique on the preview screen when your computer
system is operated under a high load (Recording and realtime preview of 8
channels at the same time which is under the setup of 720 x 240 resolution，15 fps
or more. These conditions mean the data flow on the PCI channel was
overloaded and data has been lost .It was recommanded that you DO NOT add
any other PCI interface cards besides our SV1010 video compression card.
Individual VGA Card and SATA HD Control Card please use other interface
besides PCI, e.g. PCI-E interface or PCI-X interface.
zNote 2: Please disable the function of Hyper Threading Technology on the
CPU setup page of BIOS, or the PC will crash more often.
zNote 3: The PC system should have minimum three (3) partitions. The first
partition (C:\) is reserved for the Operation System, IGUANA software and other
application software, minimum two partitions are required for IGUANA recording
files. The second HD for recording should be divided into at least two partitions. If
only one HD is available, it should be divided into at least three partitions.
4

Sunvision Scientific Inc.
BIOS Setup
zNote 4: It needs very high system resources to operate the SV101 Iguana
recording system. We recommended that you DO NOT install any other
unnecessary applications besides the OS and SV101 recording system to avoid
the recording system not working properly.
5

Sunvision Scientific Inc.
3 SV101 Components
When you receive the package of SV101, please open it and check the following
items in the package.
1. SV1018 Camera Module
2. SV1018 Camera Module warranty card
3. SV1010 Package
A. SV1010 warranty card
B. PC side connector
C. SV1010 Video Card
D. Watchdog cable
4. Mounting kit
5. Screws
6. CD
6

Sunvision Scientific Inc.
SV1018Monitor
SV1010 Package Screw Sets
CD
Mounting
Kit
SV1018
Warranty
Card
SV1010 Video Card
SV1010 Warranty Card PC Side Connector
Watchdog reset cable
7

Sunvision Scientific Inc.
3.1 SV1018 IGUANA Active Surveillance module
3.1.1 Dimension of camera module and mounting kit
Method 2 Method 1
8

Sunvision Scientific Inc.
3.1.2 Camera module allocation map
9. Screws
8. IR module
5. Motor & Mirror
module
6. Wild angel camera
7. Telescopic camera
4. Terminal board
3. Motor control
circuit board
2. Power supplier
1. Upper housing
3
2
4
1
7
5
8
6
9
3.1.3 Camera Setup
3.1.3.1 Wild angle camera setup
1: BLC (Backlight Compensating function)
2: ATW/AWC (White Balance auto tracing/auto locking)
3: MIRROR (Video mirror function)
4: ZOOM (2 times digital amplification)
9

Sunvision Scientific Inc.
The function will be activated when the switch is set on the position
of ON. The default is as the above figure shows.
Note: The function of 2x two times digital zoom can be used in the
applications where the area of interest is narrow and long. 2x digital
zoom can be activated by switching SW4 to ON position. (Please
refer to chapter 7, Camera Module Installation Tips.)
3.1.3.2 Telescopic camera setup
1: AES/ALC (Auto Electrical Shutter)
2: BLC (Backlight Compensation function)
3: AGC (Auto Gain Control)
4: ATW/AWB (White Balance auto tracing/auto locking)
5: MIRROR (Video mirror function)
6: ZOOM (2 times digital amplification)
10

Sunvision Scientific Inc.
The default value is as the above figure shows.
3.1.4 Terminal board
2
7. Outside video and RS485control
output terminal
6. Outside AC input terminal
5. AC power fuse
4. Inside AC output terminal
3. Video and RS485control input
terminal
2. Video output switch
1. RCA Video output terminal
1
7
3
6
4
5
Note: The specification of the AC fuse is 3.15A ，250VAC。
11

Sunvision Scientific Inc.
3.1.4.1 RCA video output and video output switch
B A
A: Wild angle camera output port
B: Telescopic camera output port
SW1: Wild angle camera output switch
SW3: Telescopic camera output switch
Note: The video is output to RCA video output terminal when SW1 or
SW3 is switched to Normal；The video is output to outside video
terminal when SW1 or SW3 switch to AVOUT.
3.1.5 Cable
There are two kinds of cables used by SV1018 Camera Module: 1. Signal
cable 2. AC Power supply cable
1. )Signal cable: Rated temperature 80℃CAT 5E, there are 3 kinds of CAT
5E cable: UTP、FTP、SFTP, it is recommended to use FTP or above 。PE
jacket and steel wire reinforcing are needed for outdoor applications.
12

Sunvision Scientific Inc.
2.) AC Power supply cable: (UL) SUT 105℃VW-1 18AWGx3C is used,
round shaped cable
Note: The button case of SV1018 camera module uses Lapp, PG-9 cable
gland, suitable cable diameter 3.5~8mm
3.2 SV1010 MPEG4 real time hardware compression video
card
3.2.1 Introduction to SV1010 MPEG4 video card
SV1010 MPEG4 video card interface
13

Sunvision Scientific Inc.
CN3
CN2 S1
JP1
SV1010 MPEG4 video card interface
CN3: Video input and RS485 control interface connector definition
14

Sunvision Scientific Inc.
CN2: GPIO control interface connector definition
JP1: Watchdog rest connecter
15

Sunvision Scientific Inc.
S1: Card ID &NTSC/PAL setup
If the camera module is NTSC video standard, please switch the Pin 4 to OFF.
If the camera module is PAL video standard, please witch the Pin 4 to On
When installing the first SV1010-MPEG card, switch Pin 1,2,3 to OFF.
When installing the second SV1010-MPEG card, switch Pin 1 to ON, Pin 2, 3 to
OFF.
16

Sunvision Scientific Inc.
3.3 Watchdog reset cable setup
1
2
3
Video
Card 1
Video
Card 2
MB
RST
Connector
Front panel
RST button 1 23
4
17

Sunvision Scientific Inc.
4 SV1010 PC end connector
4.1 SV1010 PC end connector Introduction
Appearance of SV1010 PC side connector
RS485-(BLUE/WHITE 1)
RS485+ (BLUE 1)
GND1 (ORANGE/WHITE 1)
CH1 (ORANGE 1)
GND0 (GREEN/WHITE 1)
CH0 (GREEN 1)
RS485-(BLUE/WHITE 2)
RS485+ (BLUE 2)
GND3 (ORANGE/WHITE 2)
CH3 (ORANGE 2)
GND2 (GREEN/WHITE 2)
CH2 (GREEN 2)
SV1010 PC side connector color code
18

Sunvision Scientific Inc.
4.2 SV1010 PC Side Connector Connection
There are two ways to connect the SV1010 PC side Connector: One is to use
the screwed terminals, the other way is to use the RJ-45 connector. Two
connectors can not be used at the same time.
When the PC is located in a humid or salty environment, metal might erode or
oxidize, the RJ-45 connector might become unreliable. It is recommended that the
screwed terminals be used in this situation.
1
2
Two ways to connect SV1010 PC side Connector
19

Sunvision Scientific Inc.
4.3 RJ45 connector PIN definition
SV1010 PC side connector RJ45 PIN color definition is different than usual
network application. Wires need to be arranged as follows to function well.
BLUE/WHITE 8
BLUE 7
BROWN/WHITE 6
BROWN 5
Orange/White 4
Orange 3
Green/White 2
Green 1
20