Super Circuits VIID1 User manual

Indoor Monitor
OPERATION INSTRUCTION
4-Wire Villa Video Intercom System
User Manual

LIMITATION OFLIABILITY
This users' manual is supplied'as is', with no warranties,be it expressed or implied,including,
but not limited to, theimplied warranties of merchantability, suitability for any exactpurpose, or
non-infringement of any third party'srights.
This publication may include technicalinaccuracies or typos. Themanufacturer holds the right
to introduce any changes tothe information contained herein, forany purpose, including but not
limited to, improvements of thepublications and/or related to theproduct, at any time, without
prior notice.
DISCLAIMER OFWARRANTY
The supplier shall not beliable to any party orany person, except for replacementor reasonable
maintenance of this product, forthe cases, included but notlimited to the following:
Any damage or loss, includingbut not limited to: direct/indirect,consequential, special, exemplary,
arising out of or relatedto the product;
Inappropriate use or negligence ofthe user in operation ofthe product, resulting in personalinjury
or any damage;
Unauthorized disassembly,repair or modification of theproduct by the user;
Any problems or consequential inconvenience,loss or damage, caused byconnecting this product
to devices of the thirdparties;
Any claim or action fordamages, brought by any photogenicsubject, be it a personor organization,
due to violation of privacywhereby the pictures taken bythe device and/or saved databecome
public or are used forthe purposes other than intended.
SAFETY INSTRUCTIONS
12
Read these instructions and keepthem in a safe placefor future reference.
Please refer all work relatedto the installation of thisproduct to qualified service personnelor
system technician.
Do not operate the appliancebeyond its specified temperature, humidityor power source ratings.
Securely install the devices onvertical surfaces (solid walls/doors) notprone to vibration or impact.
oooo
Use the appliance at temperaturesbetween 10 C ~ +60 C (14 F ~140 F) without excessive
exposure to the extreme valuesindicated.
Install the devices away fromheat sources such as radiators,heat registers and stoves.
Installation of the terminal nearconsumer electronics devices, e.g. stereoreceiver/amplifiers and
televisions, is permitted as longas the air surrounding theterminal does not exceed theabove
mentioned temperature range.
Handle the appliance with care.Do not strike or shake,as this may damage thedevice.
The doorbell/camera units should befitted with an approved weathershield if the chosen position
is in direct sunlight, orin contact with rain, snowor irrigation sprinkler systems.
Do not use strong orabrasive detergents when cleaning theappliance body.When the dirt is
hard to remove, use amild detergent and wipe gently.
Do not overload outlets andextension cords as this mayresult in a risk offire or electric shock.
Distributing, copying, disassembling, reverse compiling,reverse engineering, and also exporting
in violation of export lawsof the software provided withthis product, is expressly prohibited.
CARING FOR THEENVIRONMENT BY RECYCLING
When you see this symbolon a product, do notdispose of the product withresidential
or commercial waste.
Recycling your electrical equipment
Please do not dispose of this product with your residentialor commercial waste. Some countries or
regions, such as the European Union, have set up systemsto collect and recycle electrical and electronic
waste items. Contact your local authorities for information about practices established for your region.
COPYRIGHT STATEMENT
All rights reserved. No partof this publication may bereproduced in any form orby any means,
transcribed, translated into any languageor computer language, transformed inany other way,
stored in a retrieval system,or transmitted in any formor by any means, electronic,mechanical,
recording, photocopying or otherwise, withoutthe prior written permission ofthe owner.

INDOOR MONITOR
3
Monitoring
Speaker
TFT display View visitor imagesdisplayed on theTFT screen
Microphone
Sound from outdoor camera
Call transfer
/Surveillance Transfer call to otherextension monitor or watch theoutside image
from the standby mode.
Talk
Transmit the voice tooutdoor camera
Unlock Unlock the door lock bypressing this button
Adjust the chroma, contrast andluminace of TFT display
TalkVolume Adjust the speaker volume
Ring volume Adjust the ring volume
Allow you to observe theimage of camera view atentrance in
real time.
Start conversation with outdoor visitor via camera
Chroma /Contrast
/Luminance
Name Descriptions
9
10

Call transfer to other indoormonitor. Watch the outsideimage from the
external camera under the standbymodel
Observe the image of cameraview at entrance in realtime
Release the door lock
Activate conversation mode by pressingthis button
DESCRIPTION ON SYMBOL
DESCRIPTION ON LED INDICATOR
Adjust the chroma contrast andluminace of the TFT display
Increase/decrease the ring volume
When lit, this LED indicates this indoor unit is connected to
main power supply.
When lit, this LED indicates that this indoor unit is communicating with the
1st outdoor camera.
The front panel includes three LED indicators:
LED 3
LED 1
LED 2
When lit, this LED indicates that this indoor unitis communicating
with the 2nd outdoor camera.
Increase/decrease the talk volume
Adjust the speaker volume
Adjust the brightness of the TFT display
Adjust the chroma of the TFT display
56

WIRING DIAGRAM
If you are using only one outdoor camera, you mustconnect it to the socketmarked CN1. If the
only outdoor camera is connected to the CN2 socket,the indoor unit willdisplay a blank screen
when you attempt to activate monitoring mode to 1st outdoorcamera by pressing the button .
Please note that the part marked by the broken line is not present if youare using the indoor
unit, which has an internal switching power supply. Therefore you can connect the AC plug
directly to the AC power supply.
The functionality of terminals C N1 and CN2is shown below:
1.Red:DC12V 2.Yellow:Audio 3.Black: GND 4.White:Video
If you are using two outdoor cameras (for example, at the front door and theback gate), you must
use the CN1CN2 . The two wires for connecting to the outdoorunits are shown in
the picture below.
and sockets
Upto 4 indoor monitors canbe connected with 2 outdoor
cameras.
A. Red: Audio B. Yellow: GND C. Black: Data D. White:Video
J
CN1
C
N
2
CN3
C
N
4
1.Red
2.Yel.
3.Blk.
4.Wh.
DC12V
Audio
GND
Video
Dry
contact
4321
AC100V~240V
External switching power supply
aa
a
aa2P short pin plugged in
Video
GND
External camera
CN53
OUTDOOR
CAMERA 1
J
CN1
C
N
2
CN3
C
N
4
1.Red
2.Yel.
3.Blk.
4.Wh.
DC12V
Audio
GND
Video
Dry
contact
4321
AC100V~240V
External switching power supply
a
a
a2P short pin plugged in
Video
GND
External camera
CN53
OUTDOOR
CAMERA 2
DC12V
Audio
GND
Video
4321
A.Red
B. Yel.
C. Blk.
D.Wh.
CN3A.Red
B. Yel.
C. Blk.
J
4
CN1
(not included)CN4D.Wh.A.Red
B. Yel.
C. Blk.
D.Wh.
C
N
2
External switching power supply
CN5
2P short pin pulled
To next extention unitC 3
N
AC100v-240V
GND
Camera
DC12V
Video
Select one
C
N
2
DC12V
Audio
GND
Video
4321
(not included)
GND
Camera
DC12V
Video
Select one
OUTDOOR
CAMERA 2
GND
GND
78
C
N
2
OUTDOOR
CAMERA 1

NOTE ON WIRING CONNECTION
OPERATION INTRODUCTION
VISITOR CALL
The Visitor press
the call button on
outdoor camera 1
A 10s ofcontinuous Ding
Dong tone is played
inside and outside
The visitor's image is
automatically displayed on
the screen
release the
door lock
Standby mode
Press the unlock
button on indoor
monitor
Press the Talk button
on indoor monitor again End
The Visitor press
the call button on
outdoor camera 2
If the call buttonsoftwo outdoor camera are pressed at the same
time, the preference will be given to the outdoor camera whose
call button was pressed first, unless the call button is pressed
again after the indoor monitor goes into standby mode.
There is no indication on second outdoor camera except that a
brief tone will sound on the indoor monitor.
NOTE:
Both the sound and image from the camera remain on for 20 seconds after the
unlock button is pressed.
Start conversation
with outdoor camera
Press the Talk
button
The indoor unit will automatically go into standby mode if you are
not home or donot reach the indoor unit within 60 seconds.
The conversation
duration is 120s
at a time
Stop ringing NOTE:
Please be aware of Connectionof 2 outdoor cameras isrequired.
Please follow the terminal markings on PCB to avoid incorrect connections.
The wiring connection requirement :
1. 4C ordinary non-STPwiring cable,
Transmission 90 feet (0.2 mm = 24 AWG)
Wiring connection according to thefollowing to avoid interference
Power+ Video
Audio GND GND Audio
Power+ VideoBoth
Both outdoor units must be connected tothe main monitor. The socket marked CN1is for
outdoor camera 1, and CN2 is for outdoor camera2. Connect other extension monitors in
in serial,oneby one. The auxiliaryconnection of last extension monitor (nearthe
main monitor) is connected directly tomain monitor (the socket markedCN4).
Please note that the 2PShort Pin is designed for programming theindoor monitor (see page 7 and
8 marked as ). Theindoor monitor will be programmedto main monitor if youplug in the
2P Short Pin; however the indoor monitorwill be programmed to extensionmonitor if the
2P Short Pin is pulled out.
2. Effective distance fromthe outdoor camera to furthest indoor monitor:
Transmission 160 feet (0.3 mm = 22 AWG)
Transmission 260 feet (0.4 mm = 20 AWG)
Normally, the thesystem supports locks with NormallyOpen (N.O.) door unlocking
method. This means that inthe normal state,the drycontacts (page5) are open so thelock
is in a constant closed state.
Please verify that connections of the external power source to the power supply are correct
before applying power to the system. If connected incorrectly, severe damagecan occur.
In addition, the system also supports connectionto one external camera. You can also connect it
to one external display.For connection details (socket CN5), see the diagram below:
Video
GND
CN5
External display
Video
GND
External camera
CN5 J3
Please note that the cameraconnected to CN2 is usedto watch the image aroundthe door if
the camera of outdoor unit is masked. CN2can be only connected onedevice, so you can
select either outdoor unit 2 or the camera.
Note that the electriccurrent to camera is 300 mAmax.
If the camera in outdoorunit is
masked, and can't see theimage.
Press this button to watchthe image
from camera. Press it againto back
to the image of outdoor
unit.
910


If a conversation with outdoor unit isunderway in monitoring mode, duringthis time avisitor
press the call button oneither of outdoor unit, the monitoring mode will be switched off. the
just visitor simage will appear on itsscreen andcontinuous ringing will beheard. youcan
press the Talk button to reactivate conversation with thevisitor ;for more detailed operations,
please refer to VISITOR CALL on page 8.
MONITORING
Press the monitoring
button on indoor
monitor
Standby mode
Press the Talk
button
End
Press the monitoring
button on indoor
monitor again
display image from 2nd
outdoor camera on the
screen.
Press the Talk
button again
monitoring duration
is up to60 seconds
Press the unlock
button to release
the door lock
If youare using two outdoor cameras, but a blankdisplay appears when
you activate monitoringmode on either indoorunit, disconnect
allpower supply to the indoor unit, wait 10 seconds, then reapply
power.
Display image from 1st
outdoor camera on the
screen.
Start conversation
with outdoor camera
CALL TRANSFER TOANOTHER EXTENSION
Press this button to access
Call transfer to
other extension
Start conversation
with outdoor camera
If you are using twoindoor units, activate monitoring mode on both indoor
unit to see the same image on both screens. The image displayed depends on
which outdoorunit is being activated fromthe indoor unit, or which monitoring
button was pressed last.
When you are transferring a call to otherextension, the original
conversation indoor unit will return to standby mode,and the
indoor unit which the call is being transferredwill also sound a
continuous Ding Dong tone and the video imagewill appear on
its screen.
A continuous Ding
Dong tone is sounded
Torelease the door lock and end the conversation,please refer to page8.
NOTICE:
Press the Talk
button on any of
indoor units
Outdoor camera call indoor
monitor and conversation
is underway
NOTE:
Press this button once
more to return to
standby mode
NOTE:
If you are using onlyone outdoor camera inmonitoring mode, you can also endthe
monitoring mode by pressing themonitoring button again. T
The connectionof 2 outdoor cameras to1 indoor monitor is requiredfor dual entrance
monitoring.
INTERNAL COMMUNICATION BETWEEN INDOORUNITS
Press the Talk
button on any of
indoor units
Start conversation
among indoor units
Standby mode
Press the Talk
button
A continuous Ding
Dong tone is heard
Press the Talk
button again End
NOTE:
In internal communication mode, if a visitor presses the call
button on either outdoorunit, the internal communication
mode will be switched off. The visitor's imagewill appear
on its screen and continuous ringingwill be played. You can
press the Talk button to reactivate a conversation with the
visitor. For more detailed operations,please refer toVISITOR
CALL on page 8.
At least 2 indoor unitsare required
At least 2 indoor unitsare required
11 12

SPECIFICATIONS
Display
Resolution4inchTFTLCD
320 (RGB) x 234
Conversationduration
Standby status
Power supply
Operation temp.
Installation
Intercom mode
Working status
Surface mount
400mA max
120 seconds
NOTE:
Do not install thedevice near strong radiation sources, such as a TV set, video recorder,PC etc.
Avoid shaking,beatingon, or coliding with the device. Oherwise,internal components maybe
damaged.
Do not apply power to the device until after it is completely installed.
Position the AC powersupply at least 12 inches away from the unit to avoid interference.
INSTALLATION OF INDOORUNITSPlace the moni
Keep the unit away from thewater and magnetic eld.
Maintenance should be performed by a qualied technician.
Install the monitor in the most suitable location, and at eye level.
Plastic anchorsBracket
Connection
cable
150-160cm
Toinstall the indoor unit, please follow the diagram below:
Video systemPAL/NTSC compatible
CN5
Video
GND
External camera
Press the button to
activate the function
End
Real time
surveillance
Requirements:
1. Connect the external camera
2.In the standby mode
Display the outside image
Press the button
again to switch o
Note In monitoring mode, if a visitor presses the call buttonon either
outdoor unit,the internalcommunication mode will beswithed o.Just the
image willappear onthe screen and a continuous ringingwill be played.
You can press the Talk button to reactivate conversationwiththevisitor.
For more detailed oprations,please see VISITOR CALLon page 8.
Surveillance
MODE
50mA max.
Duplex communicationSemi-
DC12V/1A
14 ~ 140 °F (-10 ~ +60 °C)
13 14
6.7 x 4.7 x .78 inches
Dimensions