Videx IPVK Series System manual

VIDEOKIT
IPVK/6296 SERIES
IP one way, two way videokit
66550062-EN - V5.0 - 31/10/19 We recommend
This equipment is installed by a
Competent Electrician, Security or
Communications Engineer .
Installation handbook
IPVK
IPVKCRev.0.1

66550062-EN - V5.0 - 31/10/19
- 2 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
Index
System components and available versions ................................................................................................................................ 3
Art.4533 IP speaker unit module.................................................................................................................................................. 5
Art.4901 Digital codelock module................................................................................................................................................ 9
4000 Series surface and ush mounting door station installation .......................................................................................... 13
Art.6296 IP Videophone for VIDEX IP System ........................................................................................................................... 15
6200 Series Videophone wall mounting instructions ............................................................................................................... 28
Windows setup static IP address ................................................................................................................................................. 29
VX IPWIZARD Wizard conguration software for VIDEX IP System ........................................................................................ 31
Installation diagrams ................................................................................................................................................................... 48
INSTALLATION DIAGRAMS  NOTES AND SUGGESTIONS
• All diagrams refer to all kit versions: flush or surface.
• Dashed connections refer to optional connections (“Local
bell”, “Push to exit” & “Door monitor”).
• Some diagrams show how to connect a 12Vdc electric lock:
these directions are suitable for all diagrams in this manual.
• All diagrams shown are valid for systems with surface or flush
mount door station.
• To install this equipment are required expertises in the field
of information and networking technologies.
DECLETION OF RESPONSIBILITY
This manual has been written and revised carefully. The instruc-
tions and the descriptions which are included in it are referred
to VIDEX parts and are correct at the time of print. However, sub-
sequent VIDEX parts and manuals, can be subject to changes
without notice. VIDEX Electronics S.p.A. cannot be held respon-
sible for damages caused directly or indirectly by errors, omis-
sions or discrepancies between the VIDEX parts and the Manual.
WE RECOMMEND
This equipment is installed by a Competent Electri-
cian, Security or Communications Engineer
To download the programming software
VX IP Wizard and obtain the latest firmware
and manuals please visit the following web-
site and register
https://service.videx.it/
MORE INFORMATION ON PAG. 46 OF THIS MANUAL.

66550062-EN - V5.0 - 31/10/19
- 3 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
System components and available versions
IPVK/6296
Colour videokit.
50
43,8
135,0
160,0
45,0 22,7
15,7
143,0
120,0
45,0
INDOOR
STATION
Videophone
Art.6296
pag. 15
OUTDOOR
STATION
Camera unit
Art.4533
pag. 5
Flush
Mounting
Surface
Mounting
ACCESSORIES
Power supply
Art.HDR-15-12
Fig. 1 - IPVK/6296 components (measures in mm)
ONE WAY VERSIONS
IPVK-1/6296 - ush mounting
1 Outdoor station composed of:
1 Art.4533-1: 1 button camera unit
1 Art.4851: Flush mounting box
1 Colour videophone
Art.6296
1 Power supply
Art.HDR-15-12
IPVK-1S/6296 - surface mounting
1 Outdoor station composed of:
1 Art.4533-1: 1 button camera unit
1 Art.4881: Surface mounting box
1 Colour videophone
Art.6296
1 Power supply
Art.HDR-15-12
TWO WAY VERSIONS
IPVK-2/6296 - ush mounting
1 Outdoor station composed of:
1 Art.4533-2: 2 buttons camera unit
1 Art.4851: Flush mounting box
2 Colour videophones
Art.6296
2 Power supplies
Art.HDR-15-12
IPVK-2S/6296 - surface mounting
1 Outdoor station composed of:
1 Art.4533-2: 2 buttons camera unit
1 Art.4881: Surface mounting box
2 Colour videophones
Art.6296
2 Power supplies
Art.HDR-15-12

66550062-EN - V5.0 - 31/10/19
- 4 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
IPVKC/6296 Colour videokit plus a codelock module.
50135,0
280,0
45,0 22,7
263,0
INDOOR
STATION
Videophone
Art.6296
pag. 15
ACCESSORIES
Power supply
Art.HDR-15-12
OUTDOOR
STATION
Camera unit
Art.4533
pag. 5
Codelock
module
Art.4901
pag. 9
Flush
Mounting
Surface
Mounting
Fig. 2 - IPVKC/6296 components (measures in mm)
ONE WAY VERSIONS
IPVKC-1/6296 - ush mounting
1 Outdoor station composed of:
1 Art.4533-1: 1 button camera unit
1 Art.4901: Codelock module
1 Art.4852: Flush mounting box
1 Colour videophone
Art.6296
1 Power supply
Art.HDR-15-12
IPVKC-1S/6296 - surface mounting
1 Outdoor station composed of:
1 Art.4533-1: 1 button camera unit
1 Art.4901: Codelock module
1 Art.4882: Surface mounting box
1 Colour videophone
Art.6296
1 Power supply
Art.HDR-15-12
TWO WAY VERSIONS
IPVKC-2/6296 - ush mounting
1 Outdoor station composed of:
1 Art.4533-2: 2 buttons camera unit
1 Art.4901: Codelock module
1 Art.4852: Flush mounting box
2 Colour videophones
Art.6296
2 Power supplies
Art.HDR-15-12
IPVKC-2S/6296 - surface mounting
1 Outdoor station composed of:
1 Art.4533-2: 2 buttons camera unit
1 Art.4901: Codelock module
1 Art.4882: Surface mounting box
2 Colour videophones
Art.6296
2 Power supplies
Art.HDR-15-12
System components and available versions

66550062-EN - V5.0 - 31/10/19
- 5 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
Art.4533 IP speaker unit module for VIDEX IP System
E
D
C
A
F
B B
Fig. 1 Front
STEEL
ALI
HIGH BRASS
MATTE
4533-0
4533-1
4533-2
Made in Italy
RELAY 1 RELAY 2 INPUTS
EXT CAMERA
POWER ETHERNET
EXPANSION
BUTTONS
RS485
C1 NO1 NC1 NO2 NC2 C2 IN1 GNDI IN2 GND +12V RX+ RX– TX+ TX–
GND
B
A
V
JP1
GND
SL
Close
Open
PROG.
O
P
I
N
L
GH
M
EIA/TIA-568A or EIA/TIA-568B
Fare riferimento alla tabella CONNESSIONE
Fig. 2 Back
DESCRIPTION
IP speaker unit module with built-in wide colour camera with
autoiris lens and white light illumination LEDs. Depending on
the speaker unit version it includes zero, one or two call push
buttons. The unit circuitry incorporates:
• The transmitting amplifier with microphone and volume control;
• The receiving amplifier with volume control;
• Two enslavement relay to enable electric lock and an additional ser-
vice (3 contacts each: common, normally open and normally closed).
• The call buttons from 0 to a maximum of 2 depending on the
module version;
• The illumination LEDs for the card name holder;
• The camera comprised of illumination LEDs.
To download the programming software
VX IP Wizard and obtain the latest firmware
and manuals please visit the following web-
site and register
https://service.videx.it/
LEGEND
ACamera with illumination LEDs
BOperation LEDs
CLoudspeaker
DCard name holder
ECall push button (0, 1 or 2 depending on the model)
FMicrophone
GLoudspeaker volume
HMicrophone volume control
IRS485 connection terminals
LBoot loader push button for firmware update
MRS485 termination jumper
NExternal camera connection terminals
OButton expansion modules connector
PSystem connection terminals
LEDS
Flashes when the called indoor station is busy.
The LED will be off when the system is in stand-by.
If illuminated, indicates that the call from the outdoor sta-
tion is in progress. The LED will switch OFF when the call
is answered or expired the call time without any answer.
If illuminated, indicates that it is possible to speak be-
cause the call has been answered. The LED will switch
OFF at the end of a conversation (or at the end of the
conversation time).
If illuminated, indicates that the door lock has been op-
erated. It will switch OFF at the end of the programmed
“door opening” time.
CONTROLS
Microphone volume
Adjust the microphone volume.
Rotate clockwise to increase or anti-clockwise to decrease
Loudspeaker volume
Adjust the loudspeaker volume.
Rotate clockwise to decrease or anti-clockwise to increase
Rev.0.1

66550062-EN - V5.0 - 31/10/19
- 6 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
Art.4533 IP speaker unit module for VIDEX IP System
AVAILABLE VERSIONS
Art.4533-0 Art.4533-1 Art.4533-2
PROGRAMMING
The programming of the module is carried out through the VI-
DEX IP Wizard software.
There are some adjustments available directly on the module:
• Microphone volume through the relevant trimmer;
• Speaker volume through the relevant trimmer;
• RS-485 connection termination.
For the module programming refer to the section VIDEX IPWizard.
CONNECTION
EIA/TIA568A
1
2
3
4
5
6
7
8
EIA/TIA-568A
TX+
TX
RX+
RX
4533 signals RJ-45 pin
TX+ PIN 1 - White-green
TX–PIN 2 - Green
RX+ PIN 3 - White-orange
RX–PIN 6 - Orange
EIA/TIA568B
1
2
3
4
5
6
7
8
EIA/TIA-568B
TX+
TX
RX+
RX
4533 signals RJ-45 pin
TX+ PIN 1 - White-orange
TX–PIN 2- Orange
RX+ PIN 3 - White-green
RX–PIN 6 - Green
OTHER STANDARD CABLES
1
2
3
4
5
6
7
8
TX+
TX
RX+
RX
4533 signals RJ-45 pin
TX+ PIN 1 Twisted pair
TX–PIN 2
RX+ PIN 3 Twisted pair
RX–PIN 6
OPERATION
The system operation is supported by the built-in LED.
• When a visitor press a call button the units emits an intermittent deep call tone and in correspondence with the tone the red
LED flashes (Fig. 3) until the resident answer or the programmed call time expires.
• If the called indoor station is busy the red LED flashes (Fig. 4) 4 times quickly and the unit emits a deep tone on each flash.
• When the resident answers, the yellow LED (Fig. 5) illuminates and remains illuminated until the conversation terminates.
• If the resident open the door, the green illuminates (Fig. 6) for the programmed door opening time.
ERROR MESSAGES
The LED is used also to provide error messages concerning system misfunctions:
• A fast flashing LED shows connection to the push notification service is being made. This should only be temporary; if this persists then
there is something not working correctly;
• Slow flashing means that the gateway set cannot be reached;
• fixed on means that the SIP server cannot be reached or connection not allowed because of wrong credentials.
Fig. 3 Call in progress Fig. 4 Calling a busy indoor
station
Fig. 5 The conversation is in
progress
Fig. 6 Door opening
FACTORY DEFAULT PROCEDURE FOR ENTRANCE PANEL SUPPLIED WITH VIDEOKITS
The following procedure can be used to reset and pair the videophone and entrance panel supplied in a one apartment or two
apartment kit. Once paired the door panel will call the videophones without any further setup required. Additional setup is optional
to set device names, specific IP addresses etc. The default IP addresses are:
Entrance panel 192.168.1.180 // Videophone 1 192.168.1.181 // Videophone 2 192.168.1.182

66550062-EN - V5.0 - 31/10/19
- 7 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
Art.4533 IP speaker unit module for VIDEX IP System
4533 DOOR PANEL RESET FOR ONE OR TWO APARTMENT VIDEO KIT
The door panel is required to be open for this procedure.
1. Power down the door station;
2. Restore the power keeping pressed Call Button 1 (Bottom button on a 2 button panel Fig. 7) until the (red) and (green)
led’s start flashing together (Fig. 8)*;
3. Press the boot loader button once (inside the panel) (Fig. 9), the red LED will stop flashing while the green LED contin-
ues flashing together with the yellow LED (Fig. 10);
4. Press call button 1 (Fig. 11) for a one way videokit otherwise press call button 2 (Fig. 12) for a two way video kit;
5. When the button is released, the door panel emits one long beep for one way videokit or two long beeps for two way videokit
then reboots with the new settings.
* If the door panel is connected to the cloud, the LED will flash twice and the panel will reboot without changing your settings. In this case, the IP wizard must be used to make any changes
to the door panel settings.
Fig. 7 Keep pressed button 1 Fig. 8 Bell & Key LEDs flashing
STEEL
ALI
HIGH BRASS
MATTE
4533-0
4533-1
4533-2
Made in Italy
RELAY 1 RELAY 2 INPUTS
EXT CAMERA
POWER
ETHERNET
EXPANSION
BUTTONS
RS485
C1
NO1
NC1
NO2
NC2
C2
PTE1
GNDP
PTE2
GND
+12V
RX+
RX–
TX+
TX–
GND B
A
V JP1 GND SL
Close
Open
PROG.
Fig. 9 Press the boot loader button (back
of the module)
Fig. 10 Speech & Key LEDs flashing Fig. 11 One way videokit Fig. 12 Two way videokit
ENABLE BOOTLOADER MODE
In case of firmware update failure (i.e. because of mains failure
or cable disconnection during the update etc.) and the door
panel is no longer recognised by the Videx IP Wizard software,
you can try to restore it by manually putting it into boot mode.
It is strongly recommended that this operation is carried out by a
qualified engineer and in any case after a contact withVidex support.
• Disconnect the door panel from the power supply.
• Press and keep pressed the
I
button (Fig. 2 on page 5)
then connect again the power supply source.
• The door panel will go into boot mode which is indicated by
the four LED’s flashing alternatively (Fig. 13).
• Now proceed using the utility “VidexFirmwareUpdater.exe” to
upload the firmware to the device.
• If the update process terminates correctly, the device should be restored and ready to work.
• If the device still does not work, please contact the supplier to proceed according to the warranty terms.
Fig. 13 Door panel in BOOTLOADER mode

66550062-EN - V5.0 - 31/10/19
- 8 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
ADHESIVE GASKET PLACEMENT
Apply the Yseal as shown in Fig. 14.
ANTITAMPERING LOCKS FIXING
Fit the anti-tampering locks Was shown in Fig. 15.
Y
G
Fig. 14
W
Fig. 15
HOW TO REMOVE/INSERT THE CARD NAME HOLDER
• To avoid damage to the module front plate, mask the side that
will be in contact with the screwdriver blade;
• Insert the screwdriver (flat side) into the card-holder hole as
shown in Fig. 16;
• Move the screwdriver to the left as shown in Fig. 17 to extract
the card name holder;
• Edit the card name then replace it inside the holder and refit:
insert the holder inside its housing from the left or right side
then push the other side until it clips into place. Fig. 16 Fig. 17
CONNECTION TERMINAL SIGNALS
EXT
CAMERA
SL Active low output enabled when the
external video input is in use
GND Composite video signal ground reference
VComposite video signal input
RS485
ARS-485 Connection (termination adjusted
through the JP1 jumper)
B
GND
POWER +12V 12Vdc 400mA power supply input
GND
INPUTS
IN1 Active low input 1 (when enabled activate
the programmed output)
IN2 Active low input 2 (when enabled activate
the programmed output)
GNDI Ground for IN1 and IN2 inputs
ETHERNET
RX– Ethernet Connection Orange (568A)
RX+ Ethernet Connection White/Orange (568A)
TX– Ethernet Connection Green (568A)
TX+ Ethernet Connection White/Green (568A)
RELAY 2
C2 Relay 2 common contact
Max
12-24
Vac/dc
0.4A
NC2 Relay 2 normally closed contact
NO2 Relay 2 normally open contact
RELAY 1
C1 Relay 1 common contact
NC1 Relay 1 normally closed contact
NO1 Relay 1 normally open contact
TECHNICAL SPECIFICATION
Video codec: H.263
H.263+
Supported resolutions: 352x288 (CIF) used in SIP standard
mode
320x240 used between Videx devices
and app
176x144 (QCIF) used in SIP standard
mode
Audio codec: G.711 μ-law, A-law
Sampling frequency: 8 khz
SIP compatibility: SIP 2.0
Power Supply: 12Vdc - 400mA
Power consumption: Stand by: 250mA
Operating: 380mA
Working Temperature: -10 +50 °C
MAXIMUMILLUMINATIONDISTANCEFROMCAMERAATNIGHT
The illumination LED’s within the camera will
illuminate the visitor when they are within
50cm of the camera.
MAX 50 cm
CLEANING OF THE PLATE
Use a clean and soft cloth. Use moderate warm water or non-ag-
gressive cleansers.
Do not use:
• abrasive liquids;
• chlorine-based liquids;
• metal cleaning products.
Art.4533 IP speaker unit module for VIDEX IP System

66550062-EN - V5.0 - 31/10/19
- 9 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
A B
C
Fig. 1 Front
MOV
NO1 NC1 NO2 NC2 NO3 NC3
SW2
SW1
NC2
NO2 C2
NC3
NO3 C3
NC1
C1
+
NO1
Made in Italy
4901
STEEL
ALI
HIGH BRASS
MATTE
Note: Remove MOV
jumper completely
when using a relay to
trigger a gate controller.
A
BJPL ED
F
Fig. 2 Back
DESCRIPTION
The Art.4901 is manufactured from 316 grade brushed stainless
steel and the module features 12 stainless steel buttons, backlit
in blue (Keys 0 - 9, ENTER and CLEAR) and 2 LED’s for progress
information during use and programming. With three integral
relays each with common, normally open and normally closed connections and two inputs to enable the external triggering of
relays one and two (for example, push to exit button). Key presses are signalled both acoustically and visually while each button
press has a tactile feel. Entering the correct code followed by ENTER will activate the relevant relay. Programming is carried out
through the same keypad following a simple programming menu. The module can be combined with other 4000 Series modules in
an audio or video intercom system.
LEGEND
AGreen LED
BRed LED
CBacklit keypad
DJPL jumper
EMOV jumpers
FConnection terminals
MAIN FEATURES
• 3 C, NC, NO relay outputs (24Vac/dc – 5A max);
• 3 Programmable secret codes (one for each relay);
• Each relay can be set to be activated for a specific time (01 to 99 seconds) or to work as latch;
• Two active low inputs to command directly the relay 1 and 2;
• Programming menu guarded by a 4-8 digit programmable engineer’s code;
• Visual and Acoustic signal during operating and programming;
• Keypad illumination LEDs;
GENERAL DIRECTIONS FOR INSTALLATION
In order to achieve the best results from the schematics described it is necessary to install only original VIDEX equipment, strictly
keeping to the items indicated on each schematic and follow these General Directions for Installation:
• The system must be installed according to national rules in force, in any case the running of cables of any intercom unit must be
carried out separately from the mains;
• All multipair cables should be compliant to CW1308 specification (0.5mm twisted pair telephone cable).
• Cables for speech line and service should have a max resistance of 10 Ohm
• Lock release wires should be doubled up (Lock release wires and power supply wires should have a max resistance of 3 Ohm);
• The cable sizes above can be used for distances up to 50m. On distances above 50m the cable sizes should be increased to keep
the overall resistance of the cable below the RESISTANCES indicated above;
• Double check the connections before power up;
• Power up the system then check all functions.
Art.4901Digital codelock module Rev.0.1

66550062-EN - V5.0 - 31/10/19
- 10 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
LOCK RELEASE BACK EMF PROTECTION
A varistor must be fitted across the terminals on AC lock release (Fig. 3) and a diode must be fitted across the terminals on a DC lock
release (Fig. 4) to suppress back EMF voltages. Connect the components to the lock releases as shown in figures.
VARISTOR MOV
12V AC
LOCK RELEASE
Fig. 3
DIODE
1N4002
12V DC
LOCK RELEASE
Fig. 4
BUZZER BACK EMF
When using intercoms with buzzer call (Art.924/926, SMART1/2, 3101/2, 3001/2 and 3021/2) add one 0.1uF (100nF) capacitor be-
tween terminals 3 and 6 on the telephone.
BUILTIN RELAYS  BACK EMF PROTECTION
The Art.4901 includes selectable back EMF protection on the relays. The jumpers marked MOV (one jumper for each relay) are used
to select the protection type. When using a fail secure lock with connections C& NO the jumper should be in the NO position. When
using a fail open lock with connections C& NC the jumper should be in the NC position and when using the codelock to trigger a gate
controller or another third party controller the jumper should be removed completely (this disables the protection on the relay).
BACK LIGHT ADJUSTMENT JUMPER JPL
The jumper JPL (Fig.2, D) is used to adjust the brightness and determine the operation of the backlit buttons. There are four
brightness settings for the backlit buttons and two programming modes (mode 1 and 2) for the jumper.
The two modes that can be programmed change the functionality of the jumper JPL. The table below indicates the programming
mode, the position of the jumper and the operation of the backlit buttons.
Jumper Position Back light Operation
Mode 1
A
(default)
A
B
Back light on low brightness in standby. Full brightness when any buttons are pressed.
B
A
B
Back light OFF in standby. Full brightness when any buttons are pressed.
Mode 2
A or B
A
B
or
A
B
Back light on full brightness all of the time.
JPL removed in
either Mode
A
B
No back light, the back light is completely disabled.
Art.4901 Digital codelock module