Nywint IPX User manual

Please read this manual carefully before using the product you purchase, and keep it well for future
use.We reserve the right to modify the specication in this manual at any time without notice.
English
User Manual
IPXVideo Outdoor Station
IX-ENG-821-V1 202008

-1-
1.Parts and Functions
1
2
3
4
5
6
7
8
10
9
Camera lens Card Reader Window
Allows the door to be unlocked by using a
card. The door station beeps if the card can-
not unlock the door.
1 6
Microphone 821-MK Modular
2 7
Speaker
Terminal connector
Use to connect external devices to the
door station
4
10
Night View LED
Illuminates subjects in dark environments.
Lan connector
Use to connect the door station to the
network.
Screw Hole
3
9
8
Dot-matrix Display
5

-2-
3.Door Station Mounting
1 2 34
Drill a hole and attach the embedded box to it. The last view for all mounting.Use the screws to fasten the panel Wire correctly and plug in the bus line connector
Flush mounting
1 2 34
Surface mounting
1. Installation height for door station usually is 145~160cm.
2. Use screws to x the back panel to the wall after connect the cable correctly.
3. Attach the front panel to the back panel, then use the screw to x it.

-3-
4. Electric Lock Connection
12V 250mA
+
-12V
LK -
LK+
N.O.
EB -
EB +
set to Normally open on the
Unlock Relay mode
Note:
1. This mode only supports electromagnetic
locks.
2. Electromagnetic lock of Power-off-to-
unlock type should be used.
3. The door lock is limited to 12V, and
holding current must be less than
250mA.
4. The Unlock Mode Parameter of Monitor
must be set to 1 (by default).
Door Lock Controlled with Internal Power
Door Lock Controlled with Dry Contact
Note:
1. The external power supply must be used
according to the lock.
2. The inside relay contact is restricted toAC
or DC 24V/1A.
3. Setup the Unlock Mode of Monitor for
different lock types.
•Power-on-to-unlock type:Unlock
Mode=0 (by default)
•Power-off-to-unlock type:Unlock
Mode=1
+
+
-
-+12V
LK -
LK+
N.O.
EB-
EB+
set to Normally Open on the Unlock Relay mode (default)
Note: Cut off this line when using external power supply

-4-
5.Module
Press digital button to input room number / address, press “#“ button to activate the
call.
1. Setup private code on monitor:
On monitor, press “Settings” -> “Manage” -> “Private Code” ,and input 4digits pri-
vate code.
2. Unlock using private code:
On MK module, input “Call_Nbr + Private code” to unlock.
For example:
Monitor Call_Nbr settings as below:
Device_Addr: (SS)5, Private code: 6363
On MK module, input 56363 to unlock.
Call monitor
Unlock
112233
00##
778899
445566
Mechanical
keypad Connect to
main or last
module
Connect to next
module
IN
OUT
1. MK Module

-5-
1. Setup private code on monitor:
On monitor, press “settings” -> “Manage” -> “Private code”, and input 4 digits unlock
code.
2. DR Module
Card reader
area
Dot-matrix display
Features
• Management via monitor
• The distance of card reading is from 3 to 5 cm
Dot-matrix: 16 x 24 dot matrix display.
Card Reader: support 125KHz and 13.56MHz unencrypted RFID tag.
IN
OUT
Connect to
main or last
module
Connect to next
module
Card Operation
RM_ADDR, current monitor address read only
ID_input 10 digits card number for new card, must.
User name: card’s name, not essential.
Date: add date, not essential.

-6-
2. Unlock using private code
On DR module, Swipe register card on card reader window of door station to unlock.
6. Specication
●Power Source: Power-over-Ethernet (IEEE 802.3af Class 0)
●LAN Interface: 10 BASE-T / 100 BASE-TX Ethernet (RJ-45)
●Camera: Type 1/3.7" Ultra Sense, ISP with 77dB WDR
●Len angle: 170 degree with Fisheye correction
●Minimum illumination: 5 lux
●Card Reader: Support 125KHz and 13.56MHz unencrypted
●RFID tag
●Unlock Power output: 12Vdc,250mA
●Wire Type: Cat-5e or Cat-6
●Wiring Distance: 100m (Approx. 330')
●Operating temperature: -10 to +50 (oC)
●Protection: IP65;
●Dimension: 316(H)×133(W)×48(D)mm(3 GANG)
232(H)×133(W)×48(D)mm(2 GANG)

-7-
7. Wiring

Note

Note

The design and specications can be modied without notice to the user. Right to interpret
and copyright of this manual are reserved.
IX-ENG-821-V1 202008