Super-Pro DDAC-1 User manual

DDAC-1
deluxe digital
atmosphere controller
Specs 1
Basic Description 1
Installation 2
Button Functions 3-4
Error LEDs 5
Factory Settings 6
Overview 7
How to customize settings 8-12
Photocell sensitivity 12
Fuzzy logic CO2 12
How to recalibrate CO2 13
Sulfur vaporizer warning 14
Optional PC software 14
Q & A 15
Page 1 DDAC-1
Specs
Input voltage 120 Volts AC
Maximum amperage 14.5 amps @ 120 VAC
Remote COMBO probe cable length 15 ft
Temperature control range 41º to 113º F
Temperature accuracy +/- 1’F
Temperature dead-band (hysteresis) adjustable
Humidity control range 5% to 95% rH
Humidity accuracy +/- 3% rH
Humidity dead-band (hysteresis) adjustable
CO2 control range 380-2500 PPM
CO2 accuracy +/- 50 PPM
Weight 5 lbs
Dimensions 9” x 7” x 3.75”
Basic description
The DDAC-1 is designed to control humidity, temperature
and CO2. The controller has four (4) receptacles and a remote
combination probe with highly accurate temperature, humidity,
light and CO2 sensors. The fan-ventilated remote combination
sensor is designed to quickly react to changes in the growing
area and to resist EMI / EFI from electronic ballasts. The
remote sensor can be placed up to 15 feet from the controller.
Note: An optional 15 ft extension cable can be
purchased to allow the user to place the remote
sensor up to 30ft from the controller.

Page 2 DDAC-1
Installation
Secure the unit to a wall.
Determine the best location for the remote probe. Place the
probe in an area with good air movement preferably at plant
height. Avoid placing the probe in direct sunlight or under
direct HID Lighting.
NOTE: Do not place the sensor probe where it will
come in to contact with water. NOT WATER PROOF!
The remote probe has a quick disconnect to easily remove or
connect the probe. Secure the quick disconnect to the unit by
securing the QD screw to the unit.
Plug the power cable into a standard NEMA 5-15 wall outlet. A
120 volt power supply is required.
Turn the power on and allow it to warm up. This takes about 5
minutes. During the warm up period, the display will read CO2
heat.
Note: Now is the time to customize your settings
prior to connecting any equipment.
Ensure that all of the devices being connected to the controller
have the proper voltage and will not exceed the maximum
amperage rating of this unit.
NOTE: If using a large amperage device such as an
Air Conditioner or De-humidifier is used, a power
expansion module may be required.
Page 3 DDAC-1
Button Functions
The fifteen (15) buttons located on the front face control all
the functions. Pressing each button will display a function
and/or current setting(s) in the green LED window. Some
buttons perform more than one function.
Several small green LED lights or status indicators located
on the front panel will light up to show selected function when
certain buttons are pressed.
Up - Press button to increase setting
Down - Press button to decrease setting
Enter/Reset - Press button, hold for 3 seconds to enter new
setting and to reset the Min/Max range.
Temperature buttons
Temp day setting - Press button to set day cooling and
heating Settings.
Temp night setting - Press button to set night cooling and
heating Settings.
Temp dead-band - Press button to set the cooling and
heating dead-band setting.
Humidity buttons
Humid setting - Press button to set Day and Night humidity
Settings.
Humid mode - Press button to select the humidification (rH
Incr) or de-humidification (rH decr) mode.
Humid dead-band - Press button to set the humidity dead -
band setting.

Page 4 DDAC-1
CO2 buttons
CO2 PPM setting - Press button to display and/or change
CO2 Parts Per Million (PPM) setting.
CO2 dead-band - Press button to set the CO2 dead-band set-
point.
Calibrate CO2 PPM - Press button to re-calibrate the CO2
sensor.
Note: Refer to How to recalibrate CO2.
Special buttons
Temp & humid lock - Press button to lock or split the humidity
and temperature functions. The user has the option to run both
at the same time or independently.
Temp & CO2 lock - Press button to lock or split the
temperature and CO2 functions. The user has the option to
disable CO2 during exhaust fan operation, or to allow CO2
and temperature controls to function independently.
Min / Max recall - Press this button repeatedly to recall the
stored high and low recorded levels for Temperature, Humidity
and CO2. Press and hold the Enter/Reset button while the
recorded value is displayed to reset the Min/Max values.
*To change the temperature reading from F to C,
press and hold the UP and DOWN buttons for 2-3
seconds.
Page 5 DDAC-1
Error LEDs
The DDAC-1 is smart enough to monitor each of the
environmental conditions and to alert the user to a problem
with any of the devices connected to the DDAC-1. Here is how
it works.
As the unit functions normally, the environmental conditions
(temp, humidity & CO2) will be slowly but steadily changing.
These small changes are detected by the controller.
If the controller does not detect a slight change in one (or
more) environmental conditions within a 1-hour period, the unit
will de-activate the affected output and the appropriate green
Error LED will be flashing to indicate which device may have a
problem.
This safety feature is extremely important and useful to
eliminate “runaway” conditions which could result in crop
damage or other more serious problems.
If any of the Error LEDs are blinking, the user should refer to
the example below to help identify the actual cause of the
error.
* EXAMPLE: The Cooling error LED is flashing, it means
that the device connected to the Cooling output either did
not turn on OR that there is a problem with the
temperature sensor. Check the cooling device for proper
operation and verify the remote sensor is reading
properly.
Note: To reset an error, press the Enter / reset button.

Page 6 DDAC-1
Factory Settings
The DDAC-1 comes pre-programmed with factory settings.
These settings may be adjusted by the user. For best results
verify any changes after adjusting settings. The controller can
be easily reset to factory settings. (see below)
Temp day settings Cool 80°F / Heat 55°F
Temp night setting Cool 70°F / Heat 55°F
Temp dead-band 3°F / Heat and Cool
Humid settings 50 % rH
Humid mode Rh decr
Humid dead-band 3 %
CO2 PPM setting 1250 PPM
CO2 dead-band 50 PPM
Calibrate CO2 PPM 380 PPM
Temp & humid lock Split
Temp & CO2 lock Split
Reset Factory Settings - Press and hold the Enter / Reset
and down buttons for 3 seconds. The display will read f.Set.
Press the Enter/reset button again to restore the factory
default settings. When the factory reset is complete the unit
will say doNE.
Note: To change the temperature reading from F to
C, press and hold the UP and DOWN buttons for 2-3
seconds.
Page 7 DDAC-1
Overview
The individual push-
buttons on the DDAC-
1 makes changing
settings EASY.
* Press a button, the
display shows the
current setting.
* To change the
settings, use the UP
and DOWN buttons.
* Then press ENTER to
accept the new setting.

Page 8 DDAC-1
How to customize settings...
Up - Press button to increase setting
Down - Press button to decrease setting
Enter/reset - Press button, hold for 3 seconds to restart timer
or to adjust the setting. The timer will always start in the “ON”
cycle.
Temperature Display - Press and hold both the Up and Down
button for 3 seconds to change display. C for Celsius and F
for Fahrenheit
Temp day setting - There is a Day Cooling set point and a
Day Heating setting.
1) To set the Day Cooling press SET DAY TEMP, COOL__F
will be displayed. To change settings press the Up and Down
buttons. Press Enter to accept new setting.
2) To set the Day Heating press SET DAY TEMP twice,
HEAt__F will be displayed. To change settings press the Up
and Down buttons. Press Enter to accept new setting.
Temp night setting - There is a Night Cooling set point and
a Night Heating setting.
1) To set the Night Cooling press SET NIGHT TEMP,
COOL__F will be displayed. To change settings press the Up
and Down buttons. Press Enter to accept new setting.
2) To set the Night Heating press SET NIGHT TEMP a second
time HEAt__F will be displayed. To change setting press the
Up and Down buttons. Press Enter to new setting.
NOTE: To avoid both the heating and cooling device
turning on at the same time, the heating and cooling
settings must be greater than the combined dead
band settings.
Page 9 DDAC-1
Temp dead-band - There are two (2) dead band settings. One
for cooling and one for heating.
1) To set the cooling dead band, press Temp dead band.
COOL__F will be displayed. To change setting press the UP
and DOWN buttons. Press Enter to accept new setting.
2) To set the heating dead band, press Temp dead band a
second time. HEAt__F will be displayed. To change setting
press the Up and Down buttons. Press Enter to accept new
setting.
Humid setting - There is a day humidity setting and a night
humidity setting.
1) To set the daytime humidity, press the SET HUMID button.
day_rH will be displayed. Press the Up or Down button to
change daytime humidity setting. Press Enter to accept new
setting.
2) To set the nighttime humidity, press the SET HUMID button
a second time nit_rH will be displayed. Press the Up or Down
button to change the nighttime humidity setting. Press enter to
accept new setting.
Humid mode - Use this to select to humidify or to dehumidify.
Press Humid mode, the display will read the current setting,
either Humidify (rH Incr) or dehumidify (rH dEcr). Press the
Up and Down buttons to change the setting. Press Enter to
accept new setting.
Humid dead band - Pressing the Humid dead band button
and the display will read 05.0_rH (or the current setting) Press
the Up or Down buttons to change the setting. Press Enter to
accept new setting.

Page 10 DDAC-1
CO2 PPM setting - Press CO2 PPM, The current PPM setting
will be displayed. To change settings press the Up or Down
buttons. Press Enter to accept new setting.
CO2 dead band - Press button to display current setting.
Press the up or down button to change setting. Press Enter to
accept new setting
Temp & humid lock - use this function to interlock (COnnEct)
or split (SPLit) humidity and temperature. Press Temp &
humid lock button to display the setting. Press the Up and
Down buttons to change the setting. Press Enter to accept
new setting.
1) Select connect (COnnEct) if using ventilating fans only for
cooling and removing humidity. The fan will turn on when the
sensor detects a rise above the setting in either the humidity
or temperature.
2) Select split (SPLit) if using a ventilating fan or AC unit as a
cooling device and a dehumidifier to remove humidity. Each
device is controlled independently. The cooling device will turn
on when the temperature rises above the setting and the
dehumidifier will turn on when the humidity rises above the
setting.
3) Select split (SPLit) if using a fan or AC unit as a cooling
device and a humidifier to add humidity. Each device is
controlled independently. The cooling device will turn on when
the temperature rises above the setting and the humidifier will
turn on when the humidity lowers below the setting.
Temp & CO2 lock - Use this function to interlock (COnnEct)
or split (SPLit) the CO2 and temperature functions. They can
activate at the same time or independently. Press the Temp &
CO2 lock to display the setting. Press the Up or Down buttons
to change the setting. Press Enter to accept new setting.
Page 11 DDAC-1
1) Select connect mode (COnnEct) if using ventilating fans
(inside-to-outside growing area air exchange) for cooling and a
compressed CO2 setup. This will turn off the CO2 when the
fans are activated. The fans will exchange the warm-humid
inside air with the cooler-drier outside air while the CO2 is off
to prevent excess loss of CO2.
2) Select split mode (SPLit) if using a recycling air-conditioner
for cooling and compressed CO2 in the growing area where
there is no exchange of outside air. This will activate the air
conditioner independently from the CO2 allowing them to both
run at the same time.
3) Select split mode (SPLit) if using ventilating fans (inside-to-
outside growing area air exchange) for cooling and a CO2
generator. If set-up this way, the ventilation fans AND the CO2
generator will be allowed to operate simultaneously.
4) Select connect mode (COnnEct) if using a recycling air-
conditioner for cooling and a CO2 generator. This turn off the
CO2 generator when the air conditioner is operating to reduce
the amount of heat that needs to be removed by the air
conditioner.
Min/Max Recall - Press to “recall” or display the minimum and
maximum temperature, humidity, and CO2 recorded values.
Each time the button is pressed, the next setting will be
displayed.
The order of the recorded values is as follows:
Max temp, Min temp, Max humid, Min humid,
Max CO2, Min CO2
To reset the Min / Max values - Press the Enter / Reset
button and hold for 3 seconds.

Page 12 DDAC-1
Photocell Sensitivity
The sensitivity of the photocell may be adjusted.
* Press both Enter/Reset and Up buttons and hold for 3
seconds. The current photocell setting will be displayed.
* Press Up to increase the number displayed and the
sensitivity. (requires less light to activate photocell)
* Press Down to decrease the number and the sensitivity.
(requires more light to activate photocell)
Fuzzy Logic CO2 mode
“Fuzzy Logic” CO2 mode allows the user to more precisely
control the CO2 levels inside the growing area. Fuzzy Logic
works by monitoring the rising or falling CO2 level and reacting
to it by quickly activating ON / OFF the CO2 solenoid valve.
This function can ONLY be used with compressed CO2.
Fuzzy Logic mode can be activated or deactivated by pressing
Enter/Reset and holding for 5 seconds. Press Up or Down to
select generator mode (gEnErAt) if using CO2 generator or
Fuzzy logic mode (LogIcon) if using compressed CO2. Press
Enter to accept new setting.
Note* To prevent the CO2 regulator from “freezing” or not
closing when using the “fuzzy logic” mode, we recommend
using the Growop CO2 regulator designed to work with the
GrowOp controllers.
Note: Do not use Fuzzy logic mode if operating a
CO2 generator!!!
Page 13 DDAC-1
“HOW TO calibrate” CO2 PPM
1) Place the controller outdoors in a shaded area. Do not
place in direct sunlight. Keep away from people, animals and
other CO2 emitting areas.
Note: If calibration will be in a high traffic (vehicles)
area or a highly populated area a slightly increased
calibration to around 400-475 PPM is recommended.
3) Plug in the controller and allow to “warm up” for a minimum
of 30 minutes. For best results, allow to “warm up” for an hour
or longer.
4) Press Calibrate CO2 PPM to activate the automatic
calibration. The new CO2 level (380_PP) will be displayed.
Press the up or down button to change the calibration setting.
DO NOT exhale or breathe on the unit while activating the
calibration function.
5) Press Enter / Reset to start the calibration sequence,
(Co2_CAL) will be displayed. Leave controller alone for about
10 minutes.
6) When calibration is complete the display window will return
to normal display and functions. Place the sensor back into
the grow area. All other functions remain as they were prior to
calibration.

Page 14 DDAC-1
Sulfur vaporizer warning!
If a sulfur vaporizer is used, first remove the remote sensor
from the affected area or turn the controller OFF and cover the
remote sensor probe with a protective plastic bag. Remove the
bag before turning the power back ON.
Note: Failure to protect the sensor during Sulfur use
will result in damage to the infrared CO2 sensor and
void warranty.
Optional PC software
The DDAC-1 has the capability to being connected to a PC /
Laptop. When connected using our special USB interface
cable (sold separately) the software will show the current
conditions “live”. The user can record and chart their
conditions, verify outputs are ON or OFF, even make changes
to the settings. When used with second-party software such as
Go To My PC™, the user can access the DDAC-1 remotely
over the internet. *Ask your local retailer for details.
DDAC-1 remote probe assembly
Page 15 DDAC-1
Q & A
How can I tell if my CO2 reading is accurate? You can
check the calibration of the CO2 sensor by placing the sensor
outdoors for 30 minutes. It should read close to 380 PPM.
*See Calibrate CO2 PPM in the “How to set...” section.
What if my temperature is reading high? Make sure the
remote probe is not in direct lighting from HID lights or
sunlight. The probe also requires good air flow around it in
order for the internal ventilation fan to quickly sample the air.
Do I need to calibrate my humidity sensor? No. like the
temperature sensor, the humidity sensor is digital and does
not require calibration. Refer to the above if the humidity
reading does not seem accurate.
Why is the display reading Err SEn? The remote probe is
not connected and/or communicating with the controller.
Check the quick-connect cable and that the remote probe is
getting power. *Contact the factory for more info.
What if one of the of the small green Error LEDs are on?
One or more environmental conditions are not acting correctly.
Refer to the Error LEDs sections to diagnose the problem.
Why isn’t the CO2 outlet turning on? Verify the correct CO2
mode has been selected and/or verify the photocell daytime
green led is turned ON.
What if there is no power? Reset the power switch (circuit
breaker). If this continues reduce the number of devices
connected or use a power multiplier (Multi B-1 and Multi B-2)
to control devices with larger amperage.

Page 16 DDAC-1
This product conforms to USA and Canada
standards as listed below.
made in china