Superabrasive LAVINA L25EU User manual

LAVINA ELITE L25EU
User Manual
www.superabrasive.com / [email protected]

Superabrasive User Manual Original Language Lavina®25EU 12/2020
2
LAVINA ELITE L25EU.................................................................... 1
1. GENERAL INFORMATION................................................................. 3
1.1 MANUFACTURER........................................................................... 3
1.2 GENERAL DESCRIPTION ................................................................. 3
1.3 ENVIRONMENTAL CONDITIONS..................................................... 3
1.4 VACUUM CONNECTION................................................................. 3
1.5 LAVINA® 25EU MAIN COMPONENTS.............................................. 3
1.6 TECHNICAL DATA .......................................................................... 5
1.7 VIBRATIONS.................................................................................. 5
1.8 CE-CERTIFICATION......................................................................... 5
2. SAFETY INSTRUCTIONS.................................................................... 6
RECOMMENDED USE .......................................................................... 6
PROHIBITED USE ........................................................................... 6
PREPARATION FOR WORK .................................................................. 6
PROTECTION DEVICES......................................................................... 6
ARREST FUNCTIONS ...................................................................... 6
SAFE USE ..................................................................................... 6
RESIDUAL RISKS ........................................................................... 6
BEFORE YOU BEGIN ...................................................................... 6
OPERATING MACHINE ................................................................... 6
AFTER WORK IS COMPLETED............................................................... 6
THE WORK AREA ..................................................................... 6
PERSONAL PROTECTIVE ................................................................ 6
EQUIPMENT (PPE)............................................................................... 6
OPERATOR.......................................................................................... 7
3. HANDLING AND TRANSPORTATION ..................................................... 7
3.1 ADJUSTING THE HANDLE............................................................... 7
3.2 TURNING THE MACHINE FROM WORKING TO TOOL MOUNTING
POSITION............................................................................................ 7
3.3 LIFTING ......................................................................................... 8
3.4 STORAGE ...................................................................................... 8
4. OPERATION......................................................................................... 8
4.1 PRELIMINARY CONTROLS.............................................................. 8
4.2 WATER FLOW CONTROL SYSTEM................................................... 9
4.3 ADJUSTING AND MOUNTING TOOLS ........................................... 10
4.4 VACUUM CONNECTION............................................................... 10
4.5 CONTROL BOARD........................................................................ 11
4.6 STARTING THE MACHINE............................................................. 11
4.7 OPERATING THE MACHINE.......................................................... 11
4.8 STOPPING THE MACHINE............................................................. 12
5. TOOLS AND ACCESSORIES ............................................................. 12
TOOL HOLDER KEY............................................................................ 12
SECURITY PLATE FOR QUICKCHANGE PADS ....................................... 12
6. POPULAR TOOLS ........................................................................... 13
7. MAINTENANCE AND INSPECTION.................................................. 14
CLEANING......................................................................................... 14
CHECK DAILY.................................................................................... 14
CHECK EVERY 200 WORKING HOURS................................................. 14
CHECK EVERY 400 WORKING HOURS................................................. 14
VACUUM .......................................................................................... 14
WATER LEAKS ................................................................................... 14
MECHANICALPARTS ......................................................................... 14
ELECTRICAL SYSTEM.......................................................................... 15
LAVINA® 25EU ELECTRICAL SCHEMES WITH YASKAWA INVERTER ..... 15
LAVINA® 25EU ELECTRICAL SCHEMES YASKAWA CONNECTION MAIN
CIRCUIT TERMINALS.......................................................................... 16
8. TROUBLESHOOTING...................................................................... 17
INDEX OF PROBLEMS AND SOLUTIONS.............................................. 17
8.1 SEPARATING THE HEAD FROM THE CARRIAGE ............................. 17
8.2 DISMOUNTING/MOUNTING THE GUARD..................................... 19
8.3 REPLACING POWER CORD AND PLUGS......................................... 19
8.4 DISMOUNTING AND MOUNTING TOOL HOLDER TO CHANGING V-
RINGS AND FELT-RINGS..................................................................... 19
8.5 DISASSEMBLING AND MOUNTING TOOL HOLDER TO CHANGE
BUFFERS AND ELASTIC ELEMENT....................................................... 20
8.6 CORRECTING DEFLECTION OF THE USED PLANETARY CHAIN......... 21
MOUNTING NEW PLANETARY CHAIN ............................................... 21
8.7 REPLACING THE PLANETARY DRIVING CHAIN WHEEL AND
PLANETARY TENSIONER .................................................................... 22
8.8 TENSIONING AND REPLACING THE BELTS..................................... 23
8.9 REPLACING THE DRIVEN PLANETARY GEAR (SPROCKET)............... 25
8.10 REPLACING THE PULLEY UNITS................................................... 25
8.11 REPLACING THE PLANETARY UNIT.............................................. 26
8.12 MOTOR CONNECTION ............................................................... 26
8.13 FAULT DIAGNOSIS INVERTER YASKAWA V1000.......................... 27
WARRANTY AND RETURNS ............................................................... 29
WARRANTY POLICY FOR THE LAVINA® ELITE MACHINE...................... 29
RETURN POLICY FOR LAVINA® ELITE MACHINES ................................ 29
9. DISPOSAL...................................................................................... 29
10. MANUFACTURER’SCONTACTS..................................................... 29
11. SPARE PARTS............................................................................... 30
ASSEMBLY AND PARTS SPECIFICATIONS ............................................ 30
1. LAVINA®25EU GENERAL PARTS..................................................... 30
2. LAVINA® 25EU BUMPER............................................................... 30
3. LAVINA® 25EU TOP COVER 1 PARTSERROR! BOOKMARK NOT
DEFINED.
4. LAVINA®25EU GARD ASSEMBLY................................................... 31
5. LAVINA®25EU TOP COVER ASSEMBLY .......................................... 32
6. LAVINA® 25EU BOTTOM COVER 1 PARTS ...................................... 32
7. LAVINA® 25EU PLANETARY DRIVE PARTS...................................... 33
7.1. LAVINA® 25EU PULLEY UNIT ASSEMBLY.................................... 34
8. LAVINA® 25EU BOTTOM COVER 2 PARTS ...................................... 34
9. LAVINA®25EU TOOL HOLDER PARTS ............................................. 35
10. LAVINA® 25EU CARRIAGE PARTS 1.............................................. 35
11. LAVINA® 25EU CARRIAGE PARTS 2............................................. 36
12. LAVINA® 25E CARRIAGE PARTS 3 ............................................... 36
13. LAVINA® 25EU WATER TANK .................................................... 37
14. LAVINA® 25EU WATER BALL VALVE............................................. 37
16. LAVINA® 25EU WATER PUMP.................................................... 38
17. LAVINA® 25EU WATER INSTALLATION....................................... 38
18 CONTROL BOARD ASSEMBLY........................................................ 39
19 CONTROL BOX PARTS 380-400V.................................................... 40

Superabrasive User Manual Original Language Lavina®25EU 12/2020
3
1. GENERAL INFORMATION
This owner’s manual is intended for the operator of the Lavina®ELITE machine, the servicing technician as well as for anyone
involved with operating or servicing the machine. We recommend that you read the instructions very carefully and follow them
strictly. The manual includes information about assembling, using, handling, adjusting and maintaining your Lavina® ELITE floor
grinding and polishing machine.
1.1 MANUFACTURER
Superabrasive was founded in 1987, as a manufacturer of high quality diamond tools for the stone and concrete industry. Today,
Superabrasive is one of the world’s leading companies in the production of diamond tools and floor grinding machinery. At
Superabrasive, we strive to deliver the very best solutions to our customers, and enable them to work more efficiently.
1.2 GENERAL DESCRIPTION
The Lavina®ELITE machine is intended for grinding, polishing and buffing concrete, marble, granite, limestone and terrazzo
surfaces with diamond tools. Additionally, the machine could be used for grinding wood floor surfaces.
The Lavina®ELITE machine is a three-disc machine, which can be used wet or dry.
For best results, use only tools manufactured or recommended by Superabrasive and its distributors.
The Lavina® ELITE machine is manufactured and fitted for the above-mentioned applications only! Every other use may possess
risks to the persons involved.
1.3 ENVIRONMENTAL CONDITIONS
The temperature range for operating the Lavina® ELITE machine outdoors is between 41°F and 86°F or 5°C and 30°C. Never
use the Lavina® ELITE machine during rain or snow when working outdoors. When working indoors, always operate the
machine in well‐ ventilated areas.
1.4 VACUUM CONNECTION
A connection for a vacuum dust extractor is located on the carriage. The Lavina® ELITE machine does not include a vacuum dust
extractor. The customer must purchase the vacuum dust extractor separately. The vacuum dust extractor must be adapted for
floor grinders and have a minimum air displacement of 310m3/h with a negative vacuum of 21 kPa.
1.5 LAVINA® 25EU MAIN COMPONENTS
The Lavina®ELITE machine is made of two main component sections:
1.5.1 Carriage which contains:
Handle - the handle on the frame is adjustable in height and allows the operator to work in a correct and safe
posture (see point 3. Handling and transportation).
LED lights - the LED lights (Fig.1.1; Fig.1.2) enables the operator to work in darker areas. Existing lighting system
does not replace adequate overhead lighting.
The control panel (fig.1.3) is positioned on top of the frame and contains buttons and switches for start/stop the
machine also for the pump, lights, RPMs control switch, hour meter unit, EMG button and the USB port for
charging your phone.
The water tank is on the opposite side of the frame, so that the weight of the water does not affect the
operation of the machine. The frame weight, on the other hand, is fully absorbed by the driving wheels. An
electric pump sprays the water through a front mist system or internal under cover.
Power box
Water pump

Superabrasive User Manual Original Language Lavina®25EU 12/2020
4
1.5.2 Machine head which contains:
The Electric motor - its mounted on the base plate and it is driving the three heads with a belt system.
The planetary motion - it derives from the main engine, driven by a simplex roller chain.
The self‐leveling Guard is designed to have contact with the surface. Anytime, no matter the height of
the tool used.
 “Quickchange” tool holder is designed to hold the tools with “Quickchange”connection (All of our new tools
use the “Quickchange” connection and there is no more foam holders).
Figure 1.3
Figure 1.1
Figure 1.2

Superabrasive User Manual Original Language Lavina®25EU 12/2020
5
1.6 TECHNICAL DATA
1.7 VIBRATIONS
The vibrations of the machine are within the limits of directives and harmonized standards from the European Union when the
Lavina® ELITE is operated with the recommended tools and in normal conditions.
SONOROUS EMISSIONS
The sonorous emissions are within the limits of directives and harmonized standards from the European Union when the
Lavina® ELITE is operated with the recommended tools and in normal conditions. However, as previously stated, the operator
must wear ear protectors.
LABEL DATA
The data on the label provides the correct Voltage and kW (needed for operational purposes);
Weight (needed for transportation purposes); production year and serial number (needed for maintenance purposes).
CUSTOMER SERVICE
For customer assistance and technical support call your local distributor or call Superabrasive Ltd.
or visit us at: www.superabrasive.com , where you can download a copy of this manual.
1.8 CE-CERTIFICATION
The Lavina® ELITE machine is designed to operate correctly in an electromagnetic atmosphere of industrial type and is
equipped with all the mechanical and electrical safety protections in conformity with the following European CEE rules and
regulations:
The Lavina® ELITE machine complies with the Safety Directive for machines 2006/42/EC, the EMC Directive 2004/108/EC and
the Low Voltage Directive 2006/95/EC.
Also complies with the norms in use BDS EN ISO 12100, BDS EN 13862,BDS EN ISO 13857, BDS EN 349, BDS EN ISO 13850,BDS
EN 13732-1, BDS EN 953, BDS EN ISO 13849-1,BDS EN 1037, BDS EN ISO 5349-1, BDS EN ISO 11201, BDS EN ISO 3744, BDS EN
1033:2002, BDS EN 60204-1,BDS EN 1837, BDS EN 61000-6-4, BDS EN 61000-6-2, BDS EN 61000-4-2, BDS EN 61000-4-4, BDS EN
61000-4-5,BDS EN 61000-4-11, BDS EN 55016-2-1
Test results are a part of the machine’s technical information and can be sent upon a special request. The machine is delivered
with the CE mark exposed and provided with a EC declaration of conformity.
Lavina® 25EU
Voltage/Hz
3 ph x 380-400V 50-60Hz
Amperage
Max 15 Amps
Power
7,5 kW
10 HP
Tool holder rpm
400-1100 rpm
Direction off rotation
The heads have clockwise / right rotation
Working width
655 mm
25.8”
Tool diameter (QC Plate)
3x 225 mm
3x 9”
Weight
342 kg
754 lbs
Grinding pressure Weights UP
158 kg
348 lbs
Grinding pressure Weights DOWN
194 kg
428 lbs
Water feeding (with pump)
Peripheral & Front Mist
Water tank capacity
20 l
5.2 gal
Vacuum hose port
Camlock E250
Cable length
17.4 m
57 ft
Machine LxWxH
1800x710x1220 mm
71x28x48”
Packing LxWxH Crate 1
1480x840x1460 mm
58x33x57”

Superabrasive User Manual Original Language Lavina®25EU 12/2020
6
2. SAFETY INSTRUCTIONS
Recommended Use
The Lavina®E machine is designed and manufactured to grind and
polish concrete, terrazzo, and natural stone floors. It can be used
for renovation as well as for polishing. The machine is designed for
dry or wet use. When using it dry, use a vacuum of appropriate size.
For more information, please refer to the chapter on handling the
vacuum connection.
Prohibited Use
The machine MUST NOT be used:
For applications different from the ones stated in the general
description chapter.
For non-suitable materials. In environments which:
-Possess risks of explosion,
-Possess high concentration of powders or oil substances in the
air,
-Possess risks of fire Feature inclement conditions,
-Possess electromagnetic radiation.
PREPARATION FOR WORK
Make sure that:
You have closed the work area, so that no person unfamiliar with
operating the machine can enter the area.
The tool plate and tools are adjusted to the machine properly.
There are no missing parts of the machine
The machine is in upright working position.
The protection devices are working properly.
The electrical cable is free to move and follow the machine
easily.
In order to keep the electrical cable from being damaged, no
vehicle should cross the zone where electrical cables are
situated.
PROTECTION DEVICES
The machine is equipped with
several protection devices
including the following:
•An emergency stop button
•A protection skirt and a hood for protecting the tool plates.
These devices protect the operator and/or others persons from
potential injuries. Do not remove them. Before using the machine,
please ensure that all protection devices are mounted and function
properly. The Security plate prevents the QuickChange
pads to from loosening during work
Arrest Functions
Methods of arresting of the machine are following:
•Button to stop the motor (category 1)
•Emergency button (category 1)
Safe Use
The Lavina® E is designed to reduce risks correlated with its use.
However, it is not possible to fully eliminate the risks of an accident
with the machine. An unskilled or uninstructed operator may cause
correlated residual risks. Such risks are:
•Position Risks: due to operator’s incorrect working position
•Entanglement Risks: due to wearing inappropriate working
clothes
•Training Risks: due to lack of operational training.
•NOTE: In order to reduce any consequences of the
above‐ mentioned risks, we advise that machine operators
follow the instructions in the manual at all times.
Residual Risks
During the normal operating and maintenance cycles, the operator
is exposed to some residual risks, which cannot be eliminated due
to the nature of the operations.
Before You Begin
Working area must be clear from any debris or objects.
A first‐time operator must always read the manual and pay
attention to all safety instructions.
All electric connections and cables must be inspected for
potential damages.
Ground wire system of the power supply must be also
inspected.
Perform general daily inspections of the machine and inspect
the machine before each use.
Always inspect the safety devices: Mount the Security plate
for the QuickChange pads.
The emergency break must be clear and working
The tool protector must be working
The machine must be clean Never operate the machine in
the rain!
Confirm that there are no missing parts especially after
transportation, repair or maintenance.
•Before filling the water tank with water make sure the
machine is not working and the main switch is turned off.
•Before turning on the machine make sure that the base is
placed on the floor, the machine MUST NOT be in an upright
position when turned on!
Operating Machine
When operating the Lavina® E, make certain that there is no one
but you around the machine.
Never leave the machine unattended while working. The
electrical cable must move freely and must be damage‐ free.
The water hose must move freely and must be damage‐free.
Check to make sure the floor you are preparing to work on is
even. If the floor is uneven, it may damage the machine.
AFTER WORK IS COMPLETED
•Clean the machine and its surroundings properly
•Empty and clean the water tank
•Unplug the machine and wind up the electrical cable
•Store the machine in a safe place
The Work Area
•Ensure that people or vehicles do not enter the work area.
•Clear any cables or hoses from the work area.
•Always check the floor for debris.
Personal Protective
Equipment (PPE)
•Always wear safety shoes when working with the machine.
•Always wear ear protectors when working with the machine.
•All personnel in the immediate work area must wear safety
glasses with side shields.
•Always wear safety gloves when changing the tools.

Superabrasive User Manual Original Language Lavina®25EU 12/2020
7
•Always wear clothes suitable for the work environment.
OPERATOR
The operator must know the machine’s work environment.
Only one operator can work with the machine at a time. The
operator must be properly trained and well‐instructed prior
operating the machine.
•The operator must understand all the instructions in this
manual.
•The operator must understand and be able to interpret all
the drawings and designs in manual.
•The operator must know all sanitation and safety regulations
pertaining to the operation of the machine The operator
must have floor grinding experience.
•The operator must know what to do in case of emergency.
•The operator must have adequate technical knowledge and
preparation.
3. HANDLING AND TRANSPORTATION
3.1 ADJUSTING THE HANDLE
The Handle on the frame is adjustable in height and allows the operator to work in a correct and safe posture (Fig. 3.1, Fig.
3.2, Fig. 3.3, and Fig.3.5). Choose the upright position to move easy the machine.
3.2 TURNING THE MACHINE FROM WORKING TO TOOL MOUNTING POSITION
Put the handles of the carriage as shown on (Fig. 3.5).
Ensure that the water tank is empty before flipping the
machine. Push the handles and flip in position shown on
(Fig. 3.6). If necessary, help by placing your foot on the heel
near the control box. Always keep both rear wheels
locked (Fig. 3.7). Unlock the wheels (Fig. 3.8) only when
you wish to move the machine.
Figure 3.2
Figure 3.3
Figure 3.4
Figure 3.5
Figure 3.6
Figure 3.7
Figure 3.8

Superabrasive User Manual Original Language Lavina®25EU 12/2020
8
3.3 LIFTING
Lifting the machine by crane is possible by using the handles of the carriage (see fig. 3.5 and fig. 3.6).Do not lift any other loads
on the machine. Always use hoisting equipment rated for 350 kg (772 lbs) or greater.
3.4 STORAGE
Always store the LAVINA® ELITE machine in a dry place. Never
transport the LAVINA® ELITE machine unprotected; it may be
damaged if transported unprotected and exposed to rain or
snow.
When the machine is in storage and the temperature may fall
down to or below 32F (or 0oC). You should empty the water from
the system:
-Pull out the hose of the tank (Fig.3.7)
-With compressed air blow out the water from the system
in the two positions of the turn-cock.
4. OPERATION
4.1 PRELIMINARY CONTROLS
Inspect the working area as explained in the safety instructions. Fill in the water tank for wet use or connect the vacuum extractor
and ensure that the vacuum hose is clear and it will follow the machine easily.
Make sure that the electrical motor is connected with the power box and then you can connect the power cable with the electricity
and start the machine.
Figure 3.7

Superabrasive User Manual Original Language Lavina®25EU 12/2020
9
4.2 WATER FLOW CONTROL SYSTEM
The operator can direct water to be sprayed in front of the machine (Fig.4.1) by positioning the lever in the horizontal
position (Fig.4.2). Water will spray under the cover of the machine when the lever is in the vertical position (Fig.4.2). The
pressure regulator is located above the lever (Fig.4.3) and controls the water pressure in the system. You can see the
whole water flow control system - main and filtering parts in fig4.4. Fig. 4.5 and fig. 4.6 shows how to remove and clean
the filter mesh. In the instances where more water is required to spray under the cover of the machine, the orifice plate
(shown on pos.8 of table 14 in „spare pats“ ) can be removed.
ALWAYS USE CLEAN WATER TO PROTECT THE SYSTEM FROM DIRT.
Figure 4.1
Figure 4.2
Figure 4.3
Figure 4.4
Figure 4.5
Figure 4.6

Superabrasive User Manual Original Language Lavina®25EU 12/2020
10
Figure 4.7
4.3 ADJUSTING AND MOUNTING TOOLS
Lavina® 25E uses tool holder A63. With this new holder every one of our tools uses the “Quickchange” connection. To change the
tools you need first to unlock the butterfly (fig 4.6 in blue) by using the key we provide you (you can see it in the pictures fig. 4.7)
remove the security plate (fig 4.6 in red) then load the tools you want and insert the security plate again so the tools cannot go
backwards, rotate and lock the butterfly (as shown in fig.4.7). As you can see in fig. 4.6, for some of the new tools you need to
remove the security plate as they don’t need locking system at all but for the others always make sure that the tools are securely
locked.
In Lavina 25E the holder is initially mounted with 3 buffers.
Mount the tools only after ensuring that there is enough diamond bond material left. Be sure that the plates are always clean
before mounting.
WARNING: Always secure the Quick Change tools with the butterfly (Fig.4.6 in blue), lock with the tool holder key
(Fig.4.7) and make sure that the butterfly is securely locked and it holds the security plate not to fall off.
4.4 VACUUM CONNECTION
To connect a vacuum cleaner, the Lavina 25E is supplied with vacuum hose Cam Lock inlet C250 / vacuum hose diam. 2, 5 in
(63mm) (Fig.4.8).
Figure 4.8
Figure 4.6

Superabrasive User Manual Original Language Lavina®25EU 12/2020
11
4.5 CONTROL BOARD
1. Polishing/Grinding switch In “grinding” position, the
operator has the ability to control the rpm from 300 to 700
rpm. In “Polishing” position, the range increases to 300 to
1100 rpm.
2. USB charger.
3. STOP button which stops the motor.
4. EMERGENCY button used to stop the motor in case
of emergency.
5. POWER glowing button - it glows when the machine
is connected to the electricity.
6. Forward/Reverse switch. Select forward for
clockwise rotation of the grinding plates or reverse for
counterclockwise rotation of the grinding plates
(recommended configuration). The preferred operating
direction should be when the switch is in the forward
position. The proper direction of rotation of the motor
(counterclockwise) is indicated by an arrow on its cover.
7. Water pump switch. Glows in orange when the
water pump is working.
8. LED lights switch
9. QR code. When you scan it with your phone for example, it will redirect your browser to Lavina manuals page.
10. READY ON / OFF switch. If you want to start the motor it must be ON as it puts the inventor into standby mode (it glows
when it’s turned ON). If it’s off the inventor will be out of standby mode and you cannot start the motor. The switch
returns to its starting position after being released.
11. Cup holder.
12. Potentiometer.Controls the RPM of the grinding plates in a range of 300-1100 rpm.
13. RUN button. Start the motor (ready ON/OFF switch must be ON).
14. Digital Tachometer. Indicates the revolution per minute of the grinding plates (not the revolution per minute of the entire
unit).
15. ALARM/Reset button resets the alarm of the inverter. Button lights blue when the inverter goes into alarm mode
16. Phone holder.
4.6 STARTING THE MACHINE
First, follow the directions in the chapter on Safety Devices and Safety Instructions. Next, release the emergency stop (4), turn the
Ready switch (10) to the ON position to put the machine in standby mode. Check the potentiometer (12), and ensure that it is set to
the working speed. If you are working wet, add water to the floor surface by starting the pump (7). If you are working dry make sure
your machine is connected to the vacuum unit. Finally, hold the machine firmly and push the RUN button (13).
4.7 OPERATING THE MACHINE
Guide the machine in straight lines across the floor, slightly overlapping the previously completed surface with each new
line. Work at a constant speed, allowing the tools time to work at a speed appropriate for the tools’ grit size. Avoid
vibrations. Do not stop the machine while tools are still running as they will mark the surface of the floor. When working
wet, select the destination of the water feed with the water tap (fig. 4.2) and periodically run the pump to release water
onto the floor surface. Starting the pump is possible only if the machine motor is on. When working dry, check the floor
surface periodically for dust accumulation. Check regularly to see if you’re vacuum works properly.
Fgure 4.4
Figure 4.9

Superabrasive User Manual Original Language Lavina®25EU 12/2020
12
4.8 STOPPING THE MACHINE
The stopping of the machine must be done gradually until the motor stops. Do not stop moving the machine before the motor comes
to rest, as the tools could damage the surface.
To stop the machine:
1.Push the STOP button (3) .
2.Turn the ON/OFF (10) switch in position OFF, this will cut the voltage to the invertor and the green light will turn off.
5. TOOLS AND ACCESSORIES
TOOL HOLDER KEY
The tool holder key (Fig. 5.1) is used for adjusting, mounting and dismounting of
the foam plates. Always use the key for mounting.
Item number is A03.00.00.00
SECURITY PLATE FOR QUICKCHANGE PADS
Plate (Fig.5.2) used to ensure the “Quickchange” tools.
Item number is A63.00.01
Figure 5.1
Figure 5.2

Superabrasive User Manual Original Language Lavina®25EU 12/2020
13
6. POPULAR TOOLS
The heads have clockwise / right rotation. Use the black PCDs and Carbide
Scrapers / available reverse /.
QuickChange System and Tooling feature extremely fast and convenient
tool changes, and a long tool life, providing for great long‐term cost savings.
The QuickChange pads are produced in four different bonds for super hard,
hard, medium and soft concrete, in a variety of grit sizes. They are offered
with 1 or 2 buttons or rectangular segments, which allows you to
customize the aggressiveness of the cut.
CORSA HYBRID DISCS WITH QUICK CHANGE ATTACHMENT (WET OR DRY) : The new Corsa hybrid
discs are designed for scratch removal and transitioning from metal to resin tools, and are similar
to Calibra but the ceramic bond has been modified for more efficient use on soft and medium
concrete.
NATO® WITH QUICK CHANGE ATTACHMENT
Superabrasive's Nato resin pucks are a great tool choice for soft and hard concrete polishing
applications. Among the thickest diamond pads on the market - featuring a thick 12mm layer of resin
and diamonds for extra long life. Wide channels and a unique patented design allow for work on a
cleaner surface, ensuring a quality polish. Offered in wet and dry bond.
V‐HARR®Premium Polishing Pads for 9-inch TOOL HOLDERS
NOW AVAILABLE IN A QUICK CHANGE STYLE - NO FOAM PLATES NEEDED
V-Harr felt diamond pads are one of Superabrasive’s most versatile and successful diamond tools
for concrete polishing. V-Harr pads are also ideal for polishing terrazzo and hard stone floors. V-
Harr polishing pads should be used DRY on concrete! However, they will produce remarkable
gloss results on black granite when used wet.
Use Only Superabrasive’s Recommended Tools. For More Tooling Options, Visit www.superabrasive.com

Superabrasive User Manual Original Language Lavina®25EU 12/2020
14
7. MAINTENANCE AND INSPECTION
CLEANING
Keep your machine clean. Cleaning the machine on a regular basis will help detect and solve potential problems before they can cause
damage to the machine. Most importantly, check and clean the tool plate connections, power cords, plugs, vacuum hoses, and water
tank.
CHECK DAILY
After operating the Lavina®X machine, the operator should conduct a visual inspection of the
machine. Any defect should be solved immediately. Pay attention to power cords, plugs, vacuum
hoses, loose bolts or screws.
Tool holders: Buffers and elastic element are consumables and must be visually checked on a daily
basis and replaced if necessary. Make sure the flanges or discs are securely locked in place. The key
lock holders (butterflies) should also be checked.
Check the rubber buffers and make sure the holders are secure. The flange holding the buffers
(Fig.7.1‐1) has to be firmly secured to the unit. If there is a gap seen here, that means the screws
securing the holder are loose. The screws have to be tightened immediately to safely operate the
machine. Working with loose screws could cause serious damage to the machine. The tightening force
of the screws has to be 22‐25N.m (16‐18ft∙lbf).
It is very important to regularly check the screws that secure the “QuickChange” holder to the Figure
7.1 safety part (Fig.7.1‐ 2), so that the holder will not fly away if the buffers get damaged. The
“QuickChange” should also be cleaned.
.
CHECK EVERY 200 WORKING HOURS
Every 200 working hours, the operator should inspect all parts of the machine
carefully. Most importantly, inspect and clean the tool plate connections, power
cord plugs, vacuum hoses and water tank/filter. Also, check the water flow of the
pump. Check the guard assembly. Ensure the wheels are clean and rotate properly.
Inspect the control
buttons. If there are defective control parts, they should be replaced immediately.
Replace any worn vacuum or water hoses.
Open the service cover on the motor base (Fig 7.2) (Fig 7.3) to check the
planetary chain. Lubricate the chain with chain lubricant and correct the sag if
needed. (For sagging correction see TROUBLESHOOTING 8.4)
Dismount the tool holders (See TROUBLESHOOTING) and replace any parts
(elastic element, buffers, sealer caps, “O” rings) showing any damage.
CHECK EVERY 400 WORKING HOURS
In addition to checks made every 200 working hours, replace sealer and V‐rings as
described in chapter “TROUBLESHOOTING ‐ DISMOUNTING TOOL HOLDERS TO CHANGING V‐RINGS AND FELT‐RINGS.
VACUUM
As stated previously, frequently check hoses and othe r parts for clogging.
WATER LEAKS
Replace any leaking parts immediately as the water could damage your machine
.
MECHANICAL PARTS
Parts such as the belts, seal rings, cap rings, spiders and buffers and guard assembly are subject to wear and should be replaced
as needed.
Figure 7.1
Figure 7.2
Figure 7.3

Superabrasive User Manual Original Language Lavina®25EU 12/2020
15
ELECTRICAL SYSTEM
Dust should not enter the control box, as it will destroy the controls. Remove (blow out) any dust present.
LAVINA® 25EU ELECTRICAL SCHEMES WITH YASKAWA INVERTER
380-400 Volt
OPERATION
INTERVAL
Daily
Every 200
Hrs.
Every 400
Hrs.
Inspect power cords, plugs and vacuum hoses, loose bolt or
screws.
X
Check the rubber buffers, elastic element and fixing of the
holders
X
Inspect and clean the tool plate connections
X
Inspect and clean water tank, filters mesh and misting nozzle
X
X
Inspect the seal rings and bearings of the grinding units
X
Check the planetary chain and lubricate
X
X
Replace Felt-Ring and V‐rings
X
Check belts and bearings
X
Figure 7.4 /scheme 1/

Superabrasive User Manual Original Language Lavina®25EU 12/2020
16
Figure 7.6 /scheme 2/
LAVINA® 25EU ELECTRICAL SCHEMES YASKAWA CONNECTION MAIN CIRCUIT TERMINALS
Figure 7.6 /scheme 3/

Superabrasive User Manual Original Language Lavina®25EU 12/2020
17
8. TROUBLESHOOTING
INDEX OF PROBLEMS AND SOLUTIONS
8.1 SEPARATING THE HEAD FROM THE CARRIAGE
1. Unscrew the four bolts to remove the panel fig. 8.2-1.
2. Disconnect the cable of lamp and remove the lamp fig. 8.2-3.
3. Disconnect the flexible hose under the panel fig. 8.2-2. All water connections in the machines are with fitting types
“Push-in” and “Release button”.
4. Unscrew the four bolts to remove the cover fig. 8.2-4.
5. Disconnect the flexible hose which comes from the pump fig. 8.2-5.
6. Disconnect the engine cable from the power box fig. 8.2-6.
7. Release the clamp and remove the suction hose from the head fig. 8.2-7.
8. Make sure everything is disconnected fig. 8.2-8.
9. For separating the carriage from the head you need to be two people –one to hold the carriage while the other
removes the pins fig 8.2-9. After the pins are removed the person which is holding the carriage should carefully place it
on the ground without harming it fig. 8.1.
Figure 71Figure 71
Figure 8.1

Superabrasive User Manual Original Language Lavina®25EU 12/2020
18
Figure 8.2

Superabrasive User Manual Original Language Lavina®25EU 12/2020
19
8.2 DISMOUNTING/MOUNTING THE GUARD
You can dismount and mount the safe guard
without separating the carriage from the
main head. Put the machine in position to
change the tools. Unscrew the four bolts M5
from the metal cover preventing the safe
guard to fall. Dismount one of the three
holders. Dismount the safe guard.
8.3 REPLACING POWER CORD AND PLUGS
When replacing the power cord or plugs, always use cords and plugs with the same specifications as the original ones. Do
not use lower quality or different types of cords or plugs.
In addition, consider the distance between the appliance and the electrical source. The greater the distance, the greater the resistance and
the less current that will be available at the other end. This will cause a voltage drop and the inverter will switch into alarm mode. This will
also happen if several machines are working on the same line or the generator is not rated for the power needed. In general, our standard
power cable can be doubled in length; longer lengths require replacing all the cables with cables of a larger gauge rate to account for the
length and amperage.
8.4 DISMOUNTING AND MOUNTING TOOL HOLDER TO CHANGING V-RINGS AND FELT-RINGS
To check or replace the buffers and the elastic elements, the tool holders have to be dismounted.
You will need a 13mm deep metric socket with an outside diameter of no more than 3/4in to unscrew the four bolts (Fig.8.4.1) and remove
the holder (Fig.8.4.2). When the tool holder is dismounted, you can change the sealers (V‐Ring and Felt‐Ring).
By loosening four Hex cap flange bolts (Fig.8.4.3) the adaptor comes loose. Unscrew the six screws of the cap (Fig.8.4.4) holding the felt‐
ring. Take out the Felt‐Ring, adaptor and V‐Ring.
Mount the V‐Ring with the smallest lip of the V to the inside (Fig.8.4.5) ‐ simply push the V‐Ring so the top is on the same level as the
pulley top (Fig.8.2.6). Then take the adaptor and push the V‐Ring down with the adaptor (Fig.8.4.7). The lowest lip of the V‐Ring should only
barely touch its gliding surface. Mount the adaptor and the Felt‐Ring on top (Fig.8.4.7). Close the sealers with the cap (Fig.8.4.8) and screw
the bolts. Always use the original bolts. Do not push the V‐ring down with fingers.
Figure 8.4.1
Figure 8.4.2
Figure 8.4.3
Figure 8.4.4
Figure 8.4.5
Figure 8.4.6
Figure 8.4.7
Figure 8.4.8
Figure 8.3
Figure 8.4

Superabrasive User Manual Original Language Lavina®25EU 12/2020
20
8.5 DISASSEMBLING AND MOUNTING TOOL HOLDER TO CHANGE BUFFERS AND ELASTIC ELEMENT
When the TOOL HOLDER is
disassembled you can change
defective parts –elastic element,
buffers, etc.
Lift the locking pin (Fig.8.5.1) to
dismount the retaining washer
(Fig.8.5.2). Take out the screws on
the buffers and the nuts of the
elastic element (Fig.8.5.3;Fig.8.5.4).
Remove the elastic element from
the QC plate (Fig.8.5.5). While the
holder is dismounted
(Fig.8.5.6;Fig.8.5.7), clean the parts
and replace any defective ones with
new ones. Assemble the holder
with new buffers, new screws, and
new elastic element. Replace the
retaining washer (Fig.8.5.8) and
push the locking pin (Fig.8.5.9). This
will prevent the washer from falling
while mounting the holder on the
machine.
Make sure the four bolts holding
the adaptor (Fig.8.5.12) are
reliably tighten. Mount the
holder on the machine using the
same socket as mentioned in 8.2
(Fig.8.5.10;Fig.8.5.11). The
retaining washer fits into the central hole C
of adaptor and the four bolts into the thread holes
Т (Fig.8.5.12). The holder is centered on the outside
diameter of the adaptor. Ensure the holder is
properly connected to the plate of the adaptor and
then tight evenly the four bolts.Tightening force of
the bolts has to be 22...25N.m(16...18 ft/lbs).
Mounting the holder without retaining washer
(Fig.8.5.2) is INADMISSIBLE because the security
system preventing the separation of part of the
holder in case of broken buffers and elastic element
will not function!You can change the butterfly of the
holder without dismounting the holder of the machine.
You can change the butterfly of the holder without
dismounting the holder of the machine. Fig.8.5.13 is a 3‐
D section view of the holder, showing its parts. The
numbering is the same as in Spare parts.
Figure 8.5.10
Figure 8.5.11
T
C
Figure 8.5.12
Figure 8.5.13
Figure 8.5.5
Figure 8.5.1
Figure 8.5.2
Figure 8.5.7
Figure 8.5.3
Figure 8.5.4
Figure 8.5.8
Figure 8.5.9
Figure 8.5.6