Mytee Speedster 1000DX Installation and operating manual

Instruction
Manual
&
Safety Guide
myteemytee
PRODUCTS, INC.
7
SPEEDSTER
Cold Water Models
1000DX
1000DX-200
1005DX
Hot Water Models
1001DX
1001DX-200
1003DX

Thank you for choosing Mytee Products for your supply needs. By doing so, you have
joined thousands of your fellow cleaning professionals in choosing quality, service,
and value in your equipment.
This manual is designed to help you with the setup, maintenance, and operation of
your new unit. Please read and review it carefully before using the equipment for the
rst time. It also contains information on optional accessories, cleaning tips, and a
troubleshooting guide.
We here at Mytee Products would like to welcome you to the team, and wish you the
best for the future.
TABLE OF CONTENTS
Safety Precautions 2
Warranty 3
Unpacking The Machine 4
Optional Accessories 4-5
Safety Labels 6
Setup 7
Operation 8
Tips 9
Draining Recovery Tank 9
Maintenance 9
Troubleshooting Guide 11
Replacement Parts 12
myteemytee
PRODUCTS, INC.
7
CONGRATULATIONS!

2
This machine is intended for commercial use. It is designed to clean carpet and upholstery
in an indoor environment and is not constructed for any other use. Use only recommended
cleaning solutions and accessory tools.
All operators must read, understand and practice the following safety precautions.
The following safety alerts symbols are used throughout this manual as indicated in their
description:
WARNING: To warn of hazards or unsafe practices which could result in severe personal
injury or death.
FOR SAFETY: To identify actions which must be followed for safe operation of equipment.
The following information signal potentially dangerous conditions to the operator or equipment:
FOR SAFETY:
1. Do not operate machine:
• Unless trained and authorized.
• Unless operator manual has been read and understood.
• In ammable or explosive areas.
• Unless cord is properly grounded.
• With damaged cord or plug.
• If not in proper operating condition.
• In outdoor areas.
• In standing water.
2. Before operating machine:
• Make sure all safety devices are in place and operate properly.
3. When using machine:
• Do not run machine over cord.
• Do not pull machine by plug or cord.
• Do not pull cord around sharp edges or corners
• Do not unplug by pulling on cord.
• Do not stretch cord.
• Do not handle plug with wet hands.
• Keep cord away from heated surfaces.
• Report machine damage or faulty operation immediately to your distributor.
• Follow mixing and handling instructions on chemical containers.
4. Before leaving or servicing machine:
• Turn off machine.
• Unplug cord from wall outlet.
5. When servicing machine:
• Unplug cord from wall outlet.
• Avoid moving parts.
• Do not wear loose jackets, shirts, or sleeves.
• Use manufacturer supplied or approved replacement parts.
WARNING: Hazardous Voltage. Shock or electrocution can result. Always unplug ma-
chine before servicing.
WARNING: Flammable materials can cause an explosion or re. Do not use ammable
materials in tank(s).
WARNING: Flammable materials or reactive metals can cause an explosion or re.
SAFETY PRECAUTIONS
!
!
!
!
Machine must be grounded. If it should
malfunction or breakdown, grounding
provides a path of least resistance for electrical
shock. This machine is equipped with a cord
having an equipment-grounding conductor and
grounding plug. The plug must be plugged
into an appropriate outlet that is properly
installed in accordance with all local code and
ordinances. Do not remove ground pin; if
missing, replace plug before use.

3
WARRANTY
Mytee Products, Inc. endeavors to provide high quality products and product support to its customers and therefore backs
up all of its new products purchased from Mytee Products Inc. (“Mytee”) or any authorized Mytee distributor/service center
with this limited warranty. This limited warranty begins on the date of the customer’s purchase and is valid and available
to the original purchaser only. Mytee’s products are for commercial use only and are not intended for personal, family or
household uses.
HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO WARRANTY, EXPRESS OR IMPLIED, AS TO
DESCRIPTION, QUALITY, MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, PRODUCTIVE-
NESS, INFRINGEMENT, OR OTHER MATTER, OF ANY GOODS WHICH MYTEE SHALL SUPPLY. THERE ARE
NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. MYTEE SHALL IN
NO WAY BE RESPONSIBLE FOR THE PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER
ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR MYTEE ANY OTHER LIABILITY
IN CONNECTION WITH THE SALE OF MYTEE’S GOODS. THIS LIMITED WARRANTY POLICY MAY BE
CHANGED OR WITHDRAWN BY MYTEE AT ANY TIME WITHOUT NOTICE
.
WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear parts for 90 days from the date of original
purchase. “Wear parts” are items which wear out as a result of usage or the passage of time and are consumed despite at-
tempts to maintain them, such as gaskets, wheels, brass, cords, wires, electrical terminals, hoses, switches, thermostats, plas-
tisol parts, lters, bearings, brushes, solenoids, o-rings, bulbs, heating elements, castors, or other parts deemed wear items in
Mytee’s sole discretion. This warranty covers the cost of replacement only and does not cover shipping or labor costs.
PUMP, VACUUM MOTOR AND HEATER 1-YEAR LIMITED WARRANTY: Mytee warrants that pumps, vacuum
and oor machine motors, and heaters will be free from manufacturing defects, defects in workmanship, and defects in
material for one (1) year from the date of original purchase. This warranty does not apply and is void if the pump, vacuum
motor, or heater has worn brush motors, water damage, chemical build-up, chemical damage, or evidence of abuse, neglect
or tampering. This warranty covers the cost of replacement or repair only and does not cover shipping or labor costs.
HOUSING 5-YEAR LIMITED WARRANTY: For ve (5) years from the date of purchase, Mytee warrants a percentage
of the cost of replacement of rotationally-molded housings pro-rated as follows: Mytee will pay 100% of replacement cost
in the rst year from the date of purchase, 75% of replacement cost in the second year from the date of purchase, 50% in
the third year, 25% in the fourth year, and 12% in the fth year. Replacement cost does not include the cost of shipping or
labor.
LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR REPAIR OF ANY DEFECTIVE GOODS
SHALL BE THE EXCLUSIVE REMEDY UNDER ANY WARRANTY MADE BY MYTEE, WHETHER EXPRESS OR
IMPLIED. IN NO EVENT SHALL MYTEE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES,
PROPERTY DAMAGES, OR PERSONAL INJURIES.
All limited warranties are void for, and Mytee does not warrant in any way, any product that evidences misapplication,
improper installation, abuse, lack of maintenance, negligence in use or care, abnormal use, alteration of design, use of
incompatible or corrosive chemicals, use in a rental service, and/or servicing, installation of parts, or repairs by anyone other
than Mytee or a Mytee authorized distributor or service center.
Mytee may make changes in products it manufactures and markets at any time; these changes are made without obligation
to change, retrot, or upgrade any product previously sold or manufactured. Mytee has no obligation to honor the limited
warranties set forth herein unless the original purchaser, promptly upon discovering the warranty claim and prior to continu-
ing to use the product, contacts Mytee or a Mytee authorized distributor or service center to describe the claim and to re-
ceive and follow instructions for documenting and resolving the claim. In addition, the purchaser must provide the product
to which the claim applies to Mytee or a Mytee authorized distributor or service center for a thorough inspection.
If any provision or portion of this limited warranty policy is found to be unenforceable, then the remaining provisions and
portions shall remain valid and enforceable. If any provision or portion of this limited warranty policy is found to be limited
by law, then that provision or portion shall be construed to make it effective within the bounds of law. For example, if there
are legal limitations on the duration of warranties, the warranties made herein shall be construed to have the minimum dura-
tion required by law, or, if there are legal limitations of exclusion of remedies, the exclusions made herein shall be construed
to apply to the fullest extent possible without violating the law.
The validity, construction and performance of this warranty policy shall be governed by the laws of the State of California,
without respect to conicts of laws principles. The exclusive jurisdiction of any legal action arising from or related to this
warranty policy shall be in the State of California and no legal action shall be commenced elsewhere.

4
UNPACKING THE MACHINE
Before unpacking the machine, inspect all boxes and pallets for signs of shipping damage.
Please be aware that all packages leave Mytee Products in perfect condition. Any equipment or
carton damage caused during shipping is the responsibility of the freight company, and should
be handled by ling a claim with the carrier.
8100 - 15’ Vacuum/Solution Hose
8500 - 25’ Vacuum/Solution Hose
8400 - 3” Stainless Steel Upholstery Tool
H375 - Hose Hanger
OPTIONAL ACCESSORIES
E530 - (1 or 2
Depending on
Model)
12/3 50’ Yellow
Safety Cord
5000 – Electrical Converter Kit
8700 – Crevice tool
9000 – Chemical Injection Sprayer
& Adjustable Spray Gun
The following accessories and tools are available for this unit, and can be purchased separately
at your local Mytee dealer. You can nd more information on any of them at www.mytee.com
H226 -
45ODrain Elbow
Speedster Extractor

5
OPTIONAL ACCESSORIES
8300EZ – 12” Dual Jet,
S- Bend Floor Wand
8350EZ – 12” Single Jet,
Floor Wand
SM100 – Spinmaster Rotary Extractor 3601 – System Maintainer

6
SAFETY LABELS
The safety labels appear on the machine in the locations indicated. Replace labels if they become
damaged or cannot be read.
MACHINE COMPONENTS
WARNING: Flammable materials can cause an explosion or re. Do not use ammable
materials in tank(s). Flammable materials or reactive metals can cause explosion or re.
!
WARNING LABEL- Located on back. Label warns operator of safe practices of equipment.
!
Recovery Tank
Solution Tank
Motor
housing/ Base
Vacuum Hose
Connector
Solution Hose
Connector
Pressure Regulator
(200 & 450 PSI Models)
Prime Valve
(200 & 450 PSI Models)

7
SETUP
WARNING: Flammable materials can cause an
explosion or re. Do not use ammable solutions or
materials in tank(s).
FOR SAFETY: When using machine, follow mixing and
handling instructions on chemical containers.
ATTENTION: If using powdered cleaning chemicals,
mix prior to adding.
!
NOTE: Make sure the quick disconnects snap
together rmly. As you do this, always inspect
hoses for cracks or fraying. Do not use if hoses are
damaged.
3. Attach other end of solution hose to wand.
4. Attach vacuum hose to recovery tank.
5. Plug machine’s cord into a grounded wall outlet.
2. Attach solution hose. (Located front of machine.)
1. Open lid of solution tank. Fill solution tank with
water or approved cleaning agent.
FOR SAFETY: Do not operate machine unless cord is
properly grounded.
FOR SAFETY: Do not operate machine with the use of
an extension cord.
PRE-OPERATION
1. Vacuum carpet and upholstery and remove other debris.
2. Perform MACHINE SETUP procedures.
3. Inspect power cord for damage.

8
B. Pull up on power prime lever for 30 seconds.
This will prime the pump.
C. Pull up on wand lever to release air in the line.
Hold lever until you have a steady ow of water
coming out of the wand.
D. Once pump is primed and you have pressure
in the solution line, turn on heater switch(s) (if
model is equipped with heater) and wait a few
minutes for water to heat up.
E. Once water is heated, turn on vacuum motors
and begin cleaning.
F. Begin cleaning.
OPERATION
NOTE: When cleaning upholstery, always check cleaning
instructions sewn in furniture by manufacturer.
7. Turning machine on.
A. Turn pump switch on.
NOTE: STEP 7B IS FOR 1000DX-200, 1001DX-200,
1003DX, & 1005DX ONLY
VACUUM
HEATER
PUMP

9
DRAINING RECOVERY TANK
45º Elbow
FOR SAFETY: When servicing machine, unplug cord
from wall outlet.
1. Turn machine off and unplug power cord.
2. Remove solution & vacuum hose.
3.Attach 45º-drain elbow to dump valve and lift up drain
valve lever to empty recovery tank.
TIPS
1. Work away from outlet and power cord to prevent cord damage.
2. Use a recommended foam control solution in the recovery tank to prevent vacuum motor
damage. Periodically check for excessive foam buildup in solution tank, and recovery tank.
3. To clean heavily soiled areas, repeat cleaning path from different direction.
4. When ball oat shuts off vacuum, it is time to empty the dirty water from the recovery tank,
and rell solution tank.
5. After cleaning, relieve water pressure from tool before disconnecting hose. Squeeze trigger
for ve seconds after turning main power switch off.
MAINTENANCE
To keep machine in good working condition, simply follow machine’s daily and weekly
maintenance procedures. Check valves and relief valves should be replaced annually.
FOR SAFETY: When servicing machine, unplug cord from wall outlet.
MACHINE MAINTENENCE
DAILY MAINTENANCE
1. Empty and rinse out solution tank thoroughly.
2. Wipe off power cord and check for damage, replace if necessary. Coil cord neatly after use.
3. Clean machine with an all purpose cleaner and damp cloth.

10
WEEKLY MAINTENANCE (EVERY 20 HOURS OF OPERATION)
1. Flush solution system with Mytee system maintainer to dissolve normal chemical buildup.
a. Pour 7.5L (2 gal) of hot water 60°C (140°F) into solution tank. Add Mytee system
maintainer according to mixing instructions on bottle
FOR SAFETY: When using machine, follow mixing and handling instructions on chemical
containers.
b. Operate machine for one minute.
c. Shut off machine and allow remaining solution to break down chemical buildup
overnight.
d. Next day, spray out remaining solution and ush system with 11L (3gal) of clean water.
2. Inspect vacuum hoses for holes and loose cuffs. Drain and dry the vacuum hose as well.
3. Inspect spray pattern for clogging. If clogged, remove spray tips and soak them in a
recommended liquid neutralizer for up to six hours. To remove spray tip, twist spray tip body
counter-clockwise.
4. Lubricate wheels with water resistant oil.
5. Inspect machine for water leaks and loose hardware.
6. Remove oat shut-off screen from recovery tank and clean.
STORING MACHINE
1. Before storing machine, be certain to completely drain and rinse tanks of all water and
solution.
2. Drain and dry the vacuum hose as well, using the drain hose provided
3. Store machine in a dry area in the upright position.
4. Open recovery tank cover to promote air circulation
ATTENTION: Do not expose to rain. Store indoors.
ATTENTION: If storing machine in freezing temperatures, be sure that machine and
solution system are completely drained and dry.
NOTE: The oat shut off screen is not glued on.
Simply pull it off.

11
TROUBLESHOOTING
SYMPTOM: UNIT WILL NOT TURN ON:
PROBLEM: Not plugged in.
SOLUTION: Plug machine in proper outlet.
PROBLEM: Circuit breaker has popped.
SOLUTION: Reset circuit breaker. Make sure no other items are running on the same
circuit as machine. Outlet must be a 20-amp circuit.
SYMPTOM: PUMP IS NOT RUNNING PROPERLY:
PROBLEM: Quick disconnects are not completely locked together.
SOLUTION: Snap quick disconnects rmly together.
PROBLEM: The solution tank is empty.
SOLUTION: Fill the solution tank up with a premixed liquid detergent.
PROBLEM: Jet on upholstery tool is clogged.
SOLUTION: Clean jet with soft wire brush or remove jet and ush clean.
PROBLEM: Filters are clogged.
SOLUTION: Remove lters and rinse clean with water.
PROBLEM: Heater is blocked with hard water deposits.
SOLUTION: Flush out heaters with Mytee Products, Inc. system maintainer solution
PROBLEM: Brass check valve is stuck.
SOLUTION: Replace with new check valve.
PROBLEM: Pump wire has become disconnected.
SOLUTION: Reconnect wire.
PROBLEM: Switch on switch plate is bad.
SOLUTION: Replace switch.
PROBLEM: Pump motor brushes are worn out.
SOLUTION: Replace pump.
SYMPTOM: HEATER IS NOT WORKING PROPERLY:
PROBLEM: The back up sensor, mounted on the heater has popped.
SOLUTION: Reset sensor by pushing in button.
PROBLEM: Heating element is bad.
SOLUTION: Replace element.
SYMPTOM: VACUUM MOTOR IS NOT WORKING PROPERLY:
PROBLEM: Hose not connected tightly to upholstery tool or machine.
SOLUTION: Connect hose tightly.
PROBLEM: Drain valve is not shut completely.
SOLUTION: Close drain valve completely.
PROBLEM: Vacuum tank lid is not on tightly.
SOLUTION: Secure the vacuum tank tightly.
PROBLEM: Ball oat is shut off.
SOLUTION: Empty the vacuum tank of all wastewater.
PROBLEM: Water is coming out of vacuum motor.
SOLUTION: Use a low foaming detergent.
PROBLEM: Upholstery tool or wand is clogged with hair, carpet bers and or debris.
SOLUTION: Clean upholstery tool or oor wand jets.
PROBLEM: Ball oat is not installed correctly.
SOLUTION: Make sure that ball oat is rmly installed on the elbow.

12
PARTS
DESCRIPTION WHERE USED PART NUMBER
Vacuum motor 1003DX
3 stage 115v 1005DX C302
Vacuum motor 1000DX (-200)
2 stageHP, 115v 1001DX (-200) C301
Pump, 450 psi 1003DX
1005DX C313
Pump, 100 psi 1000DX
1001DX C305
Pump, 250 psi 1000DX-200
1001DX-200 C322
Quick connect ALL
Female ¼ SPEEDSTERS B102
Quick connect ALL
Male ¼” SPEEDSTERS B101
Element heater 1001DX, 1003DX
1000 watt 1001DX-200 E571
Light, green 1001DX(-200)
1003DX, 1005DX E513
Switch, 2 position ALL E515
Switch, 3 position SPEEDSTERS E516
System maintainer, Maintains all internal
12 quarts per case hose lines &
inline heaters 3601
Strainer, lter ALL
½” sol tank SPEEDSTERS B119A
Thermostat sensor 1001DX, 10003DX
210O auto 1001DX-200 E573
Thermostat sensor 1001DX, 10003DX
375O manual 1001DX-200 E574
Controller, separate 1001DX(-200)
Circuit indicator 1003DX, 1005DX E564
Brass check valve 1001DX B108

myteemytee
PRODUCTS, INC.
7
Mytee Products
13655 Stowe Drive
Poway, CA 92064
[phone]
www.mytee.com