superbrightleds LDRF-RGBW6-TC4 User manual

Wi-Fi Compatible RGBW Controller with
Sync-able RF Touch Color Remote
Instruction Sheet
Part Number:
Important: Read all instructions prior to installation.
866-590-3533 [email protected]
B
+
-S
+
-
M
+
-
M
+
-
To select a static color from any mode:
Press the color wheel to select your color. Brightness is adjustable
To select the color white from any mode:(Method 1)
Press the color wheel to select a static color.
Then press “Mode + button” once. Brightness is
adjustable.
To select the color white from any mode:(Method 2)
Press and hold “Mode - button” until the controller
stops at the previous static color(Mode 1).
Then press “Mode + button” once(Mode 2).
Brightness is adjustable.
MODE +
MODE -
Parts Included
RF Remote
White Mode
Static Color Mode
LDRF-RGBW6-TC4
2.4G
wi capable
LED controller
sold seperately
1 - 2.4GHz Wi-Fi Compatable RGB Controller
1 - 2.4GHz Sync-able RF Touch Color Remote
1 - Double-sided Tape
RF remote controller has a signal range
up to 65ft (20m) and requires 2 x AAA
batteries (not included).
Button Functions
Turn all LEDs on and off,
retaining the last setting
COLOR WHEEL Directly select color on wheel
from any mode or color selection
BRIGHTNESS +/- Dim LEDs in any static color
mode and most dynamic modes
by pressing (-) symbol. Brighten
LEDs by pressing (+) symbol
SPEED +/- Increase (+) and decrease (-)
speed on dynamic modes
MODE +/- Cycle up or down through 13
different dynamic modes and
static white, static color modes.
(Color Wheel)
B
+
-
S
+
-
M
+
-
Pre-test & Congure
May be used with RGBW strips or bars.
Connect LEDs to power supply and controller (see “Method 1” or “Method 2”
diagram).
Turn on LEDs using the included remote controller to ensure proper operation
of the LEDs, power supply, controller, and remote.
Choose suitable dry location for the power supply and controller. Before
double-sided tape is used, ensure all surfaces are clean and dry.
LDRF-RGBW6-TC4 4 channel RGBW (Red, Green, Blue, and White)
LED controller with color touchwheel for directly selecting a wide range of
colors.
Controller/Remote sets come preprogrammed and ready for use.
Offers 13 dynamic modes and static white, static color modes with
adjustable brightness, speed and mode retention (controller resumes
modes with the settings previously selected).
General Description
Instructions
If additional controllers or remotes are required, follow instructions
below.
The LDRF-RGBW6-TC4 features RF remote to controller device
pairing to help eliminate interference from other nearby units. If you
wish to control several controller devices from a single RF remote,
the controllers rst must be re-programmed.
The easiest way to re-program several controllers at once is to have
them share a power supply or all plug in to a single power strip.
Once programmed you can provide power as you would otherwise,
sharing is only needed for the programming phase to ease the
process -- Re-programming can be done one device at a time also.
SPEED +
SPEED -
Controller Pairing:
Pairing a remote to a controller:
1. Wire all controllers to one power supply or power strip
and turn the power off.
2. Turn on the power supply or power strip and press
the “Speed + button” once within 3 seconds.
3. If successful the LED product will ash twice slowly.
4. If the LED product ashes nine times quickly or not at
all, repeat steps one and two.
Unpairing a remote to a controller:
1. Wire the controller to a power supply or power
strip and turn the power off.
2. Turn on the power supply or power strip and
press and
hold the “Speed + button” once within 3 seconds.
3. If successful the LED product will ash nine times
quickly.
4. If the LED product ashes twice slowly or not at all,
repeat steps one and two.
Pairing Note:
1. One remote can be paired to any number of
controllers.
2. One controller can be paired to up to four remotes.
Controller Pairing

866-590-3533 [email protected]
Mode Function Brightness Speed Controls
1 Color wheel activated for single color Adjustable Not adjustable
2 Static White (brightness settings retain
on Mode 3 & 15)
Adjustable Not adjustable
3 Static White and color wheel activated Adjustable Not adjustable
4 6 color crossfade Adjustable Adjustable
5 Four color fade change (with White) Adjustable Adjustable
6 Four color instant change (with White) Adjustable Adjustable
7 Seven color strobe change (with white) Adjustable Adjustable
Mode Function Brightness Speed Controls
Note: “M-” button stops at mode 1
Note: “M+” button stops at mode 15
+
R
B
G
+
R
B
G
+
R
B
G
+
R
B
G
+
R
B
G
W
B
Power
(wired)
Power
(CPS)
G
R
V+
-
+
CPS Power Supply
(Match voltage to LED voltage)
To Power Supply
(Match voltage to LED voltage)
+
-RGB LED Flexible Light Strip
Single Color LED Flexible Light Strip
W
B
Power
(wired)
Power
(CPS)
G
R
V+
-
+
CPS Power Supply
(Match voltage to LED voltage)
To Power Supply
(Match voltage to LED voltage)
+
-
RGBW LED Flexible Light Strip
+
R
B
G
w
+
R
B
G
w
+
R
B
G
w
+
R
B
G
w
+
R
B
G
w
+
R
B
G
w
+
R
B
G
w
+
R
B
G
w
Touch Control
RGBW
Touch Control
RGBW
+
R
B
G
+
R
B
G
+
R
B
G
+
R
B
G
+
R
B
G
W
B
Power
(wired)
Power
(CPS)
G
R
V+
-
+
CPS Power Supply
(Match voltage to LED voltage)
To Power Supply
(Match voltage to LED voltage)
+
-RGB LED Flexible Light Strip
Single Color LED Flexible Light Strip
W
B
Power
(wired)
Power
(CPS)
G
R
V+
-
+
CPS Power Supply
(Match voltage to LED voltage)
To Power Supply
(Match voltage to LED voltage)
+
-
RGBW LED Flexible Light Strip
+
R
B
G
w
+
R
B
G
w
+
R
B
G
w
+
R
B
G
w
+
R
B
G
w
+
R
B
G
w
+
R
B
G
w
+
R
B
G
w
Touch Control
RGBW
Touch Control
RGBW
Wiring: Method 2
Wiring: Method 1
Modes List
Specications
Type 4 Channel
Input Voltage 12~24 VDC
Output 6 Amps / Ch
Total Output 24 Amps
Max Wattage 288W (12V) / 576W (24V)
Operating Temp -25°C ~ 60°C
Controller Size L3.3in x W1.7in x D.9in (86 x 45 x 23mm)
Controller Weight 55g (1.94oz)
Frequency 2.4GHz
Batteries 2 x AAA
DO NOT connect controller or LEDs directly to 120V AC power. This controller requires a 12V or 24V DC power supply.
DO NOT exceed max load of 24 Amps, overloading the controller may cause overheating, shorting, and possibly failure of controller.
Be sure the power supply is not plugged into an outlet before connecting or disconnecting any of the systems components.
DO NOT expose the controller or remote to direct or indirect moisture.
Always observe proper polarity when connecting power and load.
Safety
8 Red/White instant change Adjustable Adjustable
9 Blue/White instant change Adjustable Adjustable
10 Green/White instant change Adjustable Adjustable
11 Red strobe Adjustable Adjustable
12 Blue strobe Adjustable Adjustable
13 Green strobe Adjustable Adjustable
14 White strobe Adjustable Adjustable
15 Cycles through modes 1-14 and their
previously retained adjusted settings
Not adjustable Not adjustable