superior fires SF12-214-000 Guide

All instructions must be handed to the user for
safekeeping.
Please note : Except where otherwise stated, all rights, including copyright in the
text, images and layout of this booklet is owned by Focal Point Fires plc. You are not
permitted to copy or adapt any of the content without the prior written permission
of Focal Point Fires plc.
1
Revision A - 07/15
© 2015 Focal Point Fires plc.
MODEL SHOWN: DAWLISH OAK
INSTALLATION & ASSEMBLY INSTRUCTIONS
WOODEN FIRE LACE SURROUND
MODELS COVERED BY THESE INSTRUCTIONS
DAWLISH WHITE FIRE LACE SURROUND
CHARLOTTESVILLE WHITE FIRE LACE SURROUND
SF12-214-000
Superior Fires
Christchurch, Dorset BH23 2BT
Tel: [phone]
Fax: [phone]
www.superiorfires.co.uk
Email : [email protected].uk

H
WA
PUGS
(6X25mm)
2PCS
I
MIRROR
P ATES
(45X43mm)
2PCS
JA EN KEY 1PCS
A S S E M B L Y I N S T R U C T I O N S GB IE
1.0 IM ORTANT NOTES
Section
1.0
2.0
3.0
4.0
Contents
Important notes
Tools required
Hardware & parts list
Assembly
age No.
2
2
2
3
2.0 TOOLS REQUIRED
CODENAMEFIGURE QUANTITY
A
WOOD
DOWE S
(8X30mm)
8PCS
BCAM OCKS
(15X9mm)
4PCS
CCAM BO TS
(6X35mm)
4PCS
D
WOOD
SCREWS
(8X25mm)
21PCS
EG UE
(10G) 1PC
FSCREWS
(8X38mm)
2PCS
GSCREWS
(3X20mm)
4PCS
3.0 HARDWARE & ARTS LIST
CODENAMEFIGURE QUANTITY
①BACK
BOARD
1PC
②TOP PANE 1PC
③NARROW
INSIDE TOP
1PC
④NARROW
INSIDE EGS
2PCS
⑤WIDE INSIDE
TOP 1PC
⑥WIDE INSIDE
EGS
2PCS
⑦RIGHT SIDE
PANE
1PC
⑧EFT SIDE
PANE
1PC
To ensure safe and stable installation:
1. The assembled Fire Surround must be fixed / secured to the wall.
2. The wall must be sturdy and in good repair.
3. Some walls require alternative fixings (not included).
4. When drilling into the wall, check for hidden pipes and cables.
5.There are three options for construction of this surround.
A - with wide rebates - If you are installing this surround with a gas fire, or an electric fire where there is space in the wall to
recess the fire use parts 5 & 6, this means the laminate is up against the wall.
B - with narrow rebates - If using this surround with an electric fire and a flat wall do not use with rebates, instead use the
spacer frame from the fire, this option will give you 75mm of space behind the surround.
C - With out rebate, this option is similar to option B, but allows for 95mm of space behind the surround.
Cross head screwdriver PZ2 (3 inches in length or greater) Drill, 6mm and a 2mm suitable drill bit
Pencil Tape measure
Section
5.0
6.0
7.0
Contents
Installation
Cleaning/ finishing
Guarantee - terms and conditions
age No.
5
5
5
2© 2015 Focal Point Fires plc.

4.0 ASSEMBLY
3
GB IE
© 2015 Focal Point Fires plc.
Fixings Parts
D x 12 PCS 1
7
8
Gently lay both legs you have prepared onto a suitable protected surface. Be extremely careful not to scratch the front edges
of the legs. DO NOT DRAG THE EGS! Make sure that the legs are lifted everytime they are moved to avoid them from being
damaged.
Use 6 wood screws (D) to screw the left leg (8) to the backboard (1). Repeat the process for the right leg using (7) and back-
board (1).
STEP 1
STEP 2
Fit cam locks (B) into side panels (7&8). Using a drop of glue (E) in each dowel hole, insert 2 dowels (A) in to the left leg (8),
and repeat on the right leg (7).
Screw the cam bolts (C) into the top panel (2) and put a little glue (E) into the dowel holes. Place the top panel (2) onto the
surround, ensuring that the cam bolts (C) and dowels (A) line up with the relevant holes. Push down, check there are no gaps
and tighten the cam locks (B).
Fixings Parts
A x 4 PCS 1
B x 4 PCS 2
C x 4 PCS 7
8
⑦
⑧
①
②
①
⑧
⑦
A
C
C
C
C
A
B
B
D
B
B
D
D
D
D
D
D
D
D
D
D
D
A
A
C
CAA
B
B

4.0 ASSEMBLY - CONTINUED GB IE
4© 2015 Focal Point Fires plc.
O TION A
Place the wide inside leg panels (6) on the the back of the legs (7 and 8). Secure the two using 2x dowels (A), glue (E) and 3x
wood screws (D) in each side. Now connect the wide inside top (5) to the backboard (1) using 3x wood screws (D).
Fixings Parts
A x 4PCS 1
D x 9PCS 2
5
6
7
8
Use the Glue (E) in the dowel holes before inserting 2 dowels (A) into the left and right hand legs (7 and 8). Now put a small
amount of glue (E) in the dowel holes of the narrow inside leg panel (4). Push the narrow inside leg panel (4) on to the dowels
(A). Use 3x screws (D) on each leg to secure the panel down. Next use 3x woods screws (D) to install the narrow inside top
panel (3) to the backboard (1).
Fixings Parts
A x 4 PCS 1
D x 9 PCS 2
3
4
7
8
A
D
D
A
A
D
D
D
A
D
D
⑥
STEP 3
STEP 4
A
A
⑥
D
D
DD
D
D
⑤
②
①
⑧
⑦
O TION B
D
D
DD
D
A
A
①
②
⑦
⑧
④
③
④

5.0 INSTALLATION GB IE
5© 2015 Focal Point Fires plc.
With a pencil mark out the desired height where you would like the mirror brackets (I) to be situated on the rear of the legs. To avoid
splitting the leg, pre drill the bracket holes with a 2mm drill bit. Now attach the brackets to the legs using the 3x20mm screws (G).
Once the brackets are in position, centre and level the hearth into its final fitting position. Position the surround on the hearth to cor-
respond with the header/fireplace lintel, mark with a pencil on the wall where you wish to drill. Remove the surround and prepare the
wall from the marked positions. If using the fixings supplied, drill a hole in the wall using a 6mm drill bit. If not, use a suitable drill bit for
the wall plugs you are using. Insert the wall plugs (H) into position. Offering the surround back up into position against the wall, you are
now able to secure the surround to the wall using the 8x38mm screws (F).
6.0 CLEANING/ FINISHING
Before carrying out any of the following operations, ensure that the appliance is OFF and completely cold. Regularly clean
around the appliance to ensure that dust, fluff, pet hair etc, are kept to a minimum. There are no other specific requirements for
care, other than regular cleaning of the general appliance.
A wipe with a dry cloth is normally sufficient. DO NOT use abrasive cleaners as they can damage the finish. Test on a hidden
part before cleaning. Clean only in the direction of the grain. Regularly check the surround is securely fixed in position.
7.0 GUARANTEE - TERMS AND CONDITIONS
The 3 year guarantee commences from the date of purchase, provided that the terms and conditions are adhered to:
Registration is not required.
1. For any claim to be made within the 3 years from date of purchase you will be required to provide and supply us with your
proof of purchase.
Making a claim is easy.
If you wish to make a claim under our 3 year guarantee and all the terms and conditions for your product have been met then
please submit the following information for the attention of the 3G Service Department to the address below. Alternatively, you
can email or fax. Please note that this does not affect your statutory rights.
Focal Point Fires plc, 3G Service Department, Reid Street, Christchurch, Dorset, BH23 2BT.
Alternatively email: [email protected].uk or fax. [phone].
Details required:
1. Name, full address including post code and contact telephone number.
2. Receipt of purchase or credit card statement.
F861306
Fixings
F x 2 PCS
G x 4 PCS
H x 2 PCS
I x 2 PCS
F
H
G
I
H
G
G
G
I
F