superior fires EF11-35 Assembly Instructions

©2013 Focal Point Fires plc.
INSTALLATI N & USER INSTRUCTI NS
All instructions must be handed to the user for
safekeeping.
M DELS C VERED BY THESE INSTRUCTI NS
EF11-35
WALL M UNTED ELECTRIC FIRE
Please note: Except where otherwise stated, all rights,
including copyright in the text, images and layout of this
booklet is owned by Focal Point Fires plc. You are not
permitted to copy or adapt any of the content without
the prior written permission of Focal Point Fires plc.
1
Revision A - 07/13
EF11-35
Model shown : Shaftesbury
GB IE
Superior Fires
Christchurch, Dorset BH23 2BT
Tel: [phone]
Fax: [phone]
www.superiorfires.co.uk
e : [e-mail]

IMP RTANT - THESE INSTRUCTI NS SH ULD BE READ CAREFULLY AND RETAINED F R FUTURE REFERENCE.
When using this electrical appliance, basic precautions should be followed to reduce the risk of fire, electric shock and injury to person, including the
following:
• This heater must be used on an AC supply only and the voltage marked on the heater’s rating label must correspond to the supply voltage.
• Do not switch the appliance on until it is properly installed as described in this manual.
• The heater must not be located immediately above a socket outlet.
• Keep furniture, curtains and other fabric material away from the appliance.
• Do not leave the appliance unattended during use.
• This appliance is intended for household use and should not be used for industrial purposes.
• From time to time, check the cord for damage. Never use the appliance if the cord or any part of the appliance shows signs of damage. A damaged
cord must only be replaced by a qualified person.
• Do not operate this appliance with a damaged plug or cord, after a malfunction or after being dropped or damaged in any way.
• Repairs to electrical appliances should only be performed by a qualified electrician. Improper repairs may place the user at serious risk.
• Do not run the mains cable under carpets, rugs etc.
• Do not cover or obstruct the heater in any way. verheating will result if it is accidentally covered.
• Never immerse the product in water or any other liquids.
• Do not use this heater where it may come into contact with water e.g. in bathrooms, shower rooms etc.
• Do not use the appliance outdoors.
• Before cleaning the appliance, ensure it is unplugged from the power and that it is completely cool.
• Do not clean the appliance with abrasive chemicals.
• Never use accessories that are not recommended or supplied by the manufacturer. It could cause danger to the user or damage to the appliance.
• There are no other replacement parts. All other servicing should be referred to a qualified engineer.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not lift the appliance by the front panel.
• CAUTI N! In order to avoid a hazard due to inadvertent resetting of the thermal cut out, this appliance must not be supplied through an
external switching device such as a timer or connected to a circuit that is regularly switched on and off by the utility.
• CAUTI N! Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and
vunerable people are present.
• Do not insert or allow foreign objects to enter the inlet or outlet vents as this may result in electric shock, fire or damage to the appliance.
• Do not install the fire using an extension cord.
• Unplug from the mains supply if the appliance is not to be used for long periods.
• WARNING! This heater is equipped with a device to control the room temperature. Do not use this heater in small rooms when they are
occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
WARNING! Children of less than 3 years should be kept away unless continuously supervised. Children aged 3 years and less than 8 years shall
only switch on/off the applaince provided that it has been placed or installed in its intended normal operating position and they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards involed. Children aged from 3 years and less than 8
years shall not plug in, regulate and clean the applaince or perform user maintenance.
This appliance is designed to be wall hung, using the wall fixtures/fixings provided. D N T recess any part of appliance into the wall.
The appliance is supplied with a pre-wired three pin plug (13 Amp fuse rated) and 1.8 metres of electrical cable. It is therefore necessary for a
suitable electrical socket to be located within this distance and be easily accessible.
Supply Voltage: 220~240V AC, 50Hz Fuse Rating: 13 Amp
Heating Elements: 1800W Lighting: LED
This fire is fitted with LED’s (Light Emitting Diode) in place of conventional bulbs. LED’s generate the same light levels as conventional bulbs,
but use a fraction of the energy consumed. LED’s are maintenance free and will not require replacing during the life of the product.
Read all the instructions before continuing to unpack or install this appliance. Carefully remove the appliance from its packaging and lay on
the floor with it’s back surface downward. Note: D N T stand the appliance on its frame as this may cause distortion. Check that the
remaining packaging contents correlate with the component checklist below. Please dispose of all packaging at your local recycling centre.
©2013 Focal Point Fires plc.
I N S TA L L AT I N & U S E R I N S T R U C T I N S
2
GB IE
2.0 INSTALLATI N REQUIREMENTS
4.0 UNPACKING THE APPLIANCE
3.0 APPLIANCE DATA
Section Contents Page No.
1.0 Important Notes 2
2.0 Installation Requirements 2
3.0 Appliance Data 2
4.0 Unpacking the Appliance 2
5.0 Component Checklist 3
Section Contents Page No.
6.0 Site Requirements 3
7.0 Clearances to Combustibles 3
8.0 Installing the Appliance 3
9.0 perating the Appliance 4
10.0 Cleaning and Maintenance 4
11.0 Guarantee - Terms and Conditions 5
1.0 IMP RTANT N TES

QUANTITY DESCRIPTI N
1 Wall heater
1 Decorative fascia
1 Rear fascia (selected models only)
1 Instruction booklet
1 Remote control
1 Pack of fixing screws and wall plugs (5 x 40mm pozi pan head screws / 5 x wall plugs)
1 Wall mounting bracket
This appliance is designed to be wall mounted using the mounting bracket and fixings provided. The wall should be relatively flat and not
interfere with any of the ventilation slots in the rear panel.
The wall must be structurally sound and of a material capable of withstanding moderate heat. Finished plaster, conventional wallpaper,
dry-lined plaster board are examples of suitable materials. Materials such as flock, blown vinyl, embossed paper and cloth wall coverings which
are sensitive to even small amounts of heat should be avoided, as some discolouration may occur.
It should be noted that the appliance creates warm convected air currents. These currents move heat from the room surroundings to, and up
the wall surfaces adjacent to the heater.
Installing the heater next to these types of wall coverings or operating the heater where impurities in the air, (such as tobacco smoke) exist,
may slightly discolour wall finishing.
If the appliance is to be mounted on a dry lined or timber framed construction then the integrity and ability of the wall to carry the weight
of the appliance must be confirmed. It is important in these circumstances that any vapour barrier and/or structural members of the house
frame are not damaged.
If you are unsure of the ability of the wall to carry the weight and/or which type of wall fixing to use, you should take professional advice and
obtain the correct fixings. Alternatively, find a more suitable wall location.
D N T
• mount on a ceiling or floor
• recess any part of the appliance into the wall, or run the supply cable under carpets
• site any electrical equipment e.g. plasma screen TV sets etc, on the wall below the appliance.
• site in a position where curtains or drapes could cover the appliance, or other soft materials could cover e.g. below a coat rack
• site behind an opening door where mechanical impact/damage could occur
• site where the supply cable would become a trip hazard
• sit, stand or forcefully pull on the appliance
• obstruct, cover or force items into the openings
• use the heater to dry clothes
• site/use in an outdoor location(s)
It is important that the following clearances are maintained from the appliance to combustible materials. These clearances are dependent on
the mounting location as defined below:
• The minimum distance from the top of the appliance to a ceiling is 300mm
• The minimum distance from the bottom of the appliance to the floor is 200mm
• The minimum distance to the sides of the appliance is 100mm
• The minimum distance to the front of the appliance is 500mm
CAUTI N: D N T C NNECT THE APPLIANCE T THE
ELECTRICAL SUPPLY AT THIS TIME.
Focal Point Fires plc. assumes absolutely no responsibility for injuries and damages that may
occur due to improper installation or handling.
Remove any protective film coatings from the finished/decorative surfaces of the appliance, if
any. After having selected the final mounting position of the appliance taking into account the
integrity of the wall the firebox of the appliance may be secured to the wall.
To ensure customer safety, be sure to design the installation so that the strength of both the
wall and any wall fixings used are sufficient. The appliance should not be installed until all wet
plastering and/or dry wall sanding and wall painting has been completed. Do not block the
ventilation holes of the appliance. The wall onto which the appliance is installed must be flat.
Install only on a vertical surface. Avoid sloped surfaces. Installation onto anything other than
a vertical wall may result in fire, damage or injury.
If the appliance is to be mounted on the inner leaf of a conventional cavity brick wall, or a
solid wall, then the wall plugs and fixing screws provided may be used. Depending on the
condition of the wall it may be necessary to use additional fixings. In this situation, any
additional fixings and wallplugs should be of the same size and type as the ones provided.
If the appliance is to be mounted on a dry lined wall or a timber framed construction wall then efforts should be made to fix in at least two
©2013 Focal Point Fires plc.
7.0 CLEARANCES T C MBUSTIBLE MATERIALS
8.0 INSTALLING THE APPLIANCE
3
The wall where the appliance is to be
installed must be capable of
long-term support of the total load of
the appliance. Measures should also
be taken to ensure sufficient strength
to withstand the force of
earthquakes, vibration and other
external forces. Plasterboard alone is
not considered to be a structural
material. It is not recommended to
rely on plasterboard fixings alone to
support the weight of the appliance.
WARNING
Figure 1

5.0 C MP NENT CHECKLIST GB IE
6.0 REQUIREMENTS

positions vertically, into one of the wooden studs, or supporting wooden members of the
wall using two of the fixing screws provided. If this is not achievable then the wall should be
strengthened using appropriate building materials.
If there is no alternative than to rely on some plasterboard fixings then special cavity screw
fixings or hollow wall anchors will be required which are not supplied with this product. These
should be constructed from metal and not plastic and of the design indicated (Figure 1). For
further guidance for wall fixing in timber framed buildings refer to any relevant local codes of
practice.
For optimum viewing install the fire out of direct sunlight. Ensure that the bracket is level by
using a spirit level whilst marking out the hole positions. Fix the wall bracket using the plugs
and screws provided. Carefully lift the heater up ensuring that the top rear ledge of heater
engages with the wall bracket and is sitting centrally. This process should be carried out by
two people to avoid injury or damage to property or the appliance.
Gently bring the heater down against the wall. Mark the lower fixing bracket one fixing hole
position on the wall, remove the heater. Drill the wall and insert the wall plug. Refit the
heater to the wall and fasten the bottom fixing bracket to the wall using the screw
provided to permanently fix the heater in place (Figure 2).
Place the front surround over the front of the fire aligning the slots in the brackets at each
side of the front panel with the lugs on the sides of the fire (Figure 3). Again two people will
be required for this operation.
Check that the fan outlet, mounted underneath the appliance, is not covered or obstructed
in any way. Ensure the power to the fire is switched N.
REM TE C NTR L
P WER - N/ FF
FF will cancel the FF TIMER and the flame brightness slowly fades to FF.
FLAME BRIGHTNESS (5 settings)
Press ∧ /∨ to adjust the brightness level
FULL (5) - HIGH (4) - MEDIUM (3) - L W (2) - DIM (1)
HEATING (7 settings)
Press ∧ /∨ to adjust the temperature level
60℃/99°F - 30℃/86°F - 28℃/82°F - 26℃/78°F - 24℃/75°F - 22℃/71°F - FF - (L P)
FF TIMER
Press to set the FF TIMER
10m - 20m - 30m - 40m - 50m - 1H - 2H - 3H - 4H - 5H - 6H - 7H - 8H - 9H - (L P)
EMBER/FUELBED EFFECT
Press to select the dynamic fuelbed effect
C NTR L PANEL
P WER N/ FF
FLAME BRIGHTNESS (5 settings)
Press to adjust the brightness level
FULL (5) - HIGH (4) - MEDIUM (3) - L W (2) - DIM (1) - (L P)
HEATING (7 settings)
Press ∧ /∨ to adjust the temperature level
60℃/99°F - 30℃/86°F - 28℃/82°F - 26℃/78°F - 24℃/75°F - 22℃/71°F - FF - (L P)
Press button for 10s to convert between ℃and ℉(model dependent)
EMBER/FUELBED EFFECT
Press to select the dynamic fuelbed effect
ALWAYS DISC NNECT THE APPLIANCE FR M THE MAINS SUPPLY UTLET
S CKET BEF RE UNDERTAKING ANY CLEANING R MAINTENANCE!
For general cleaning use a soft clean duster - never use harsh abrasive or cleaners. The glass viewing screen should be cleaned carefully with a
soft cloth. D N T use proprietary glass cleaners.
If in doubt consult a qualified electrician. Refer to Section 3.0 Appliance Data for fuse specification. Excluding fuses, use only genuine
manufacturers spare parts available from your supplier.
©2013 Focal Point Fires plc.
4
Figure 3
9.0 PERATING THE APPLIANCE - READ BEF RE USE
10.0 CLEANING AND MAINTENANCE
8.0 INSTALLING THE APPLIANCE - C NTINUED GB IE
Figure 2