Supermicro X9DR3-F User manual

SUPERMICR R
ContaCt InformatIon
• www.supermicro.com(Email:[email protected])
• Manuals:http://www.supermicro.com/support/manuals
• Drivers&Utilities:ftp://ftp.supermicro.com
• Safety:http://www.supermicro.com/about/policies/safety_information.cfm
PaCkage Contents
(Appliestosingle-packonly)
X9DR3-F/X9DRi-F
QuICk referenCe guIde 1.0b
• One(1)SupermicroMotherboard
• Two(2)SerialATACables
• One(1)I/OShield
• Two(2)I-PasstoSerialATACables(X9DR3-F)
• One(1)I-PasstoSerialATACable(X9DRi-F)
MNL-1259-QRG 1.0b
© 2013 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
This motherboard supports up to 1 TB of Load Reduced (LRDIMM), 512 GB of
Registered (RDIMM) or 128 GB of Unbuffered (UDIMM) ECC/Non-ECC DDR3
800/1066/1333/1600/1866 MHz 240-pin 4-channel memory modules in 16 DIMM
slots.
Note: For memory optimization, use only DIMM modules that have been validated by Supermicro.
For the latest memory updates, please refer to our website at http://www.supermicro.com/
products/motherboard.
Jumper Item # Description Default
JBT1 27 Clear CMOS None
JPB1 14 BMC Enabled Pins 1-2 (Enabled)
JPG1 12 VGA Enabled Pins 1-2 (Enabled)
JPL1 11 GLAN1/GLAN2 Enable Pins 1-2 (Enabled)
JPME1 18a Management Engine (ME)
Recovery Mode
Pins 1-2 (Normal)
JPME2 32a Management Engine (ME)
Manufacture Mode
Pins 1-2 (Normal)
JWD 23 Watch Dog Pins 1-2 (Reset)
Connector Item # Description
COM1, COM2 1, 15 Back Panel Com Port1 / Front Accessible COM2 Header
Fan 1~3 45, 44, 43 CPU/System Fan Headers
Fan 4~6 42, 9, 10 CPU/System Fan Headers
FanA, FanB 41, 33 CPU/System Fan Headers
I-SATA 0/1 31 Intel SB SATA 3.0 Connectors 0/1
I-SATA 2~5 30 Intel SB SATA 2.0 Connectors 2~5
J22 (JPWR3) 46 ATX 24-Pin Power Connector
JD1 37 Speaker/Power LED Indicator
JF1 39 Front Panel Control Header
JI2C1/JI2C2 17, 16 SMBus I2C Header
JIPMB1 18 4-Pin External BMC I2C Header (for IPMI card)
JL1 29 Chassis Intrusion
JOH1 38 Overheat LED Indicator
JPI2C1 48 Power Supply SMBus I2C Header
JPWR1/2 49, 47 12V 8-Pin Power Connectors
JSTBY1 34 Standby Header
JTPM1 19 TPM (Trusted Platform Module) Port 80
JWF1 28 SATA DOM (Disk on Module) Power Connector
LAN1, LAN2 6, 7 G-bit Ethernet Ports 1/2
(IPMI) LAN 3IPMI Dedicated LAN
SCU 0~3 36 SCU Connectors 0~3
SCU 4~7 35 SCU Connectors 4~7 (for X9DR3-F only)
SP1 32 Onboard Buzzer (Internal Speaker)
T-SGPIO 1, 2 21, 20 Serial Link General Purpose I/O Headers
BP USB 0/1, USB 2/3 2, 4 Back Panel USB 0/1, 2/3
USB 4/5, USB 6, 25, 22 Front Panel Accessible USB Connections
USB 8/9, USB 10/11 24, 26 Front Panel Accessible USB Connections
VGA 8Back Panel VGA Port
Note: Item num-
bers are listed in
counterclockwise
order.
Motherboard Layout and Features Jumpers, Connectors and LED Indicators
Jumpers
Connectors
LED Indicators
CPU Installation
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide. Note: Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, and LED indicators. Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
=mounting hole
Heatsink Installation JF1 Header Pins
Power Button
OH/Fan Fail LED
1
NIC1 LED
Reset Button
2
HDD LED
Power LED
Reset
PWR
Vcc
Vcc
Vcc
Vcc
Ground
Ground
1920
Vcc
X
Ground NMI
X
Vcc
PWR Fail LED
NIC2 LED
LE1
JWF1
SP1
JIPMB1
BT1
JBT1
JWD
JPB1
JI2C1JI2C2
JSTBY1
JL1
JF1 FAN3 FAN2
FAN1
FAN4
FANB
FANA
JTPM1
JPWR1 JPWR2
JPI2C1
X9DR3/i-F
SCU4~7 SCU0~3
P2 DIMMH2 P2 DIMMG2 P2 DIMMH1 P2 DIMMG1
P2 DIMME1 P2 DIMME2
P2 DIMMF1
P2 DIMMF2
P1 DIMMA2
P1 DIMMA1 P1 DIMMB2 P1 DIMMB1
P1 DIMMD2 P1 DIMMD1
P1 DIMMC1 P1 DIMMC2
CPU2 SLOT6 PCI-E 3.0 X16 CPU2 SLOT5 PCI-E 3.0 X8
CPU2 SLOT4 PCI-E 3.0 X16
CPU1 SLOT3 PCI-E 3.0 X8
CPU1 SLOT2 PCI-E 3.0 X16
CPU1 SLOT1 PCI-E 3.0 X8
TPM/PORT80
USB 8/9
USB 4/5
USB 10/11
USB6
I-SATA2 ~ ISATA5 I-SATA0/1
T-SGPIO2
T-SGPIO1
COM2
LAN
CTRL
BMC
CTRL
SIO
BIOS
JPWR3
Rev. 1.11a
Battery
DM1
JD1
JOH1
J21
JITP0
JPG1
J22
LAN2
IPMI_LAN
VGA COM1
KB/Mouse
USB 0/1
LAN1 USB 2/3
FAN6 FAN5
JPL1
J29
J30
PHY
CLOSE 1st
OPEN 1st
CPU1
CLOSE 1st
OPEN 1st
CPU2
Intel PCH
1
46
1
47
1
48
1
49
1
5
1
9
1
14
1
10
1
15
1
4
1
8
1
13
1
3
1
7
1
12
1
17
1
18
1
19
1
20
1
2
1
6
1
11
1
16
1
21
1
26
1
31
1
36
1
41
1
37
1
42
1
43 1
44
1
45
1
38
1
39
1
40
1
32
1
33 1
34 1
35
1
27
1
28
1
29
1
30
1
22
1
23
1
24
1
25
1
1
OPEN1st
Socket Keys
1.
2.
CPU Keys
Insert the desired number of DIMMs into the memory slots, starting with P1-DIMMA1.
For memory to work properly, follow the tables below for memory population order.
Refer to the motherboard layout (at left) for the location of the DIMM slots.
Processors and their Corresponding Memory Modules
CPU# Corresponding DIMM Modules
CPU 1 P1-
DIMMA1
P1-
DIMMB1
P1-
DIMMC1
P1-
DIMMD1
P1-
DIMMA2
P1-
DIMMB2
P1-
DIMMC2
P1-
DIMMD2
CPU2 P2-
DIMME1
P2-
DIMMF1
P2-
DIMMG1
P2-
DIMMH1
P2-
DIMME2
P2-
DIMMF2
P2-
DIMMG2
P2-
DIMMH2
Processor and Memory Module Population for Optimal Performance
Number of
CPUs+DIMMs
CPU and Memory Population Conguration Table
(For memory to work properly, please follow the instructions below.)
1 CPU &
2 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1
1 CPU &
4 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1
1 CPU &
5-8 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 + Any memory pairs in P1-
DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2 slots
2 CPUs &
4 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1
2 CPUs &
6 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1
2 CPUs &
8 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-
DIMMG1/P2-DIMMH1
2 CPUs &
10-16 DIMMs
CPU1/CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-
DIMMG1/P2-DIMMH1 + Any memory pairs in P1, P2 DIMM slots
2 CPUs &
16 DIMMs
CPU1/CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/
P2-DIMMG1/P2-DIMMH1,P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-
DIMME2/P2-DIMMF2/P2-DIMMG2/P2-DIMMH2
Back Panel IO Connectors
Memory Support
DIMM Installation
Screw #1
Screw #2
Screw #4
Motherboard
Screw #3
Mounting Hole
A. COM 1 F. USB 3
B. USB 0 G. GLAN1
C. USB 1 H. GLAN2
D. IPMI LAN I. VGA
E. USB 2
A
B
C
D
E
F
G
HI
LED Item # Description Color/State Status
DM1 13 BMC Heartbeat LED Green: Blinking BMC Normal
LE1 40 Standby PWR LED Green: On SB Power On
18a
1
32a
JPME1
JPME2