SUPERMICR R
CONTACT INFORMATION
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: ftp://ftp.supermicro.com
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
PACKAGE CONTENTS
(Applies to single-pack only)
X9DRL-3F/X9DRL-iF
QUICK REFERENCE GUIDE REV. 1.00
• One (1) Supermicro Motherboard
• Six (6) Serial ATA Cables (X9DRL-iF)
• Eight (8) Serial ATA Cables (X9DRL-3F)
• One (1) I/O Shield
MNL-1298-QRG REV. 1.00
© 2012 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written
consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
This motherboard supports up to 256 GB of Registered (RDIMM)/Load Reduced
(LRDIMM) ECC or up to 64 GB of Unbuffered (UDIMM) ECC/Non-ECC DDR3
800/1066/1333/1600 MHz 4-channel memory in 8 DIMM slots.
Note:For memory optimization,use only DIMMmodules thathavebeen validatedbySupermicro.
For the latest memory updates, please refer to our website at http://www.supermicro.com/
products/motherboard.
JSD1
P2-DIMMH1
P2-DIMMG1
P2-DIMMF1
P2-DIMME1
P1-DIMMD1
P1-DIMMC1
P1-DIMMB1
P1-DIMMA1
COM1
JPW4
JTPM1
LAN1LAN2
COM2
JPW1
JPW2
JPI2C1
JIPMB1
FAN3
FAN4
FAN1
FAN5
FAN2
FAN6
JPG1
JPB1
JWD1
JPL2
JPL1
LED2
LEDM1
JD1
JF1
S-SGPIO2
T-SGPIO1
I-SATA0
I-SATA1
SAS/SATA1
SAS/SATA2
SAS/SATA3
S-SAS4
S-SAS5
S-SAS6
S-SAS7
JL1
JI2C1
JI2C2
I-SATA2
I-SATA5
I-SATA4
I-SATA3
JBT1
JSTBY1
Battery
UID
SLOT1 PCI-E 2.0 X1
USB0/1USB2/3
USB5
USB4
PCH
SLOT2 PCI 33MHZ
PCH SLOT3 PCI-E 2.0 X4 (IN X8)
CPU1 SLOT4 PCI-E 3.0 X8
CPU1 SLOT5 PCI-E 3.0 X8
CPU1 SLOT6 PCI-E 3.0 X8)
X9DRL-iF
Rev. 1.01
IPMI_LAN
BUZZER
KB/MOUSE
FANA
FANB
VGA
USB8/9
USB6/7
S-SGPIO1
SAS/SATA0
JOH1
LED1
JUIDB1
J9
T-SGPIO2
BMC CTRL
BIOS
LAN CTRL LAN CTRL
BMC Firmware
CPLD
Intel PCH
CLOSE 1st
OPEN 1st
CPU1
CLOSE 1st
OPEN 1st
CPU2
Jumper Item # Description Default
JBT1 26 Clear CMOS See Chpt. 2 in User Manual
JI2C1/JI2C2 43, 42 SMB to PCI-E Slots Off (Disabled)
JPB1 14 BMC Enabled Pins 1-2 (Enabled)
JPG1 18 VGA Enabled Pins 1-2 (Enabled)
JPL1/JPL2 13, 12 GLAN1/GLAN2 Enable Pins 1-2 (Enabled)
JWD1 31 Watch Dog Timer Enable Pins 1-2 (Reset)
Connector Item # Description
COM1/COM2 1, 16 Back Panel COM Port1 / Front Accessible COM2 Header
Fan 1~3 47, 46, 45 CPU/System Fan Headers
Fan 4-6 44, 2, 11 CPU/System Fan Headers
FanA, FanB 41, 40 CPU/System Fan Headers
JD1 36 Speaker/Power LED Indicator
JF1 35 Front Panel Control Header
JIPMB1 38 4-pin External BMC I2C Header (for an IPMI Card)
JL1 29 Chassis Intrusion
JOH1 32 Overheat LED Indicator
JPI2C1 48 Power Supply SMBbus I2C Header
JPW1/2 49, 50 12V 8-Pin Power Connectors
JPW4 51 24-Pin ATX Main Power Connector
JSD1 30 SATA DOM (Device on Module) Power Connector
JSTBY1 37 +5V Standby Power Header
JTPM1 17 TPM (Trusted Platform Module)/Port 80
JUIDB1 9 UID (Unit Identification) Switch
LAN1/LAN2 6, 7 G-bit Ethernet Ports 1/2
(IPMI) LAN 4 IPMI Dedicated LAN
(I-)SATA0~1 28 Intel PCH SATA Connectors 0/1
(I-)SATA2~5 27 Intel PCH SATA Connectors 2~5
(S-)SATA0~3 25 SATA Connectors 0~3 (X9DRL-iF)
(S-)SAS0~7 22 SAS Connections 0~7 (for X9DRL-3F only)
(S-)SGPIO1/2 24, 23 Serial (SAS) General Purpose I/O Headers 1/2
(T-)SGPIO1/2 33, 34 Serial (SATA) General Purpose I/O Headers 1/2
USB 0/1, 2/3 21, 20 Front Panel USB Connections 0/1, 2/3
USB 4 19 FP-Accessible Type AUSB Connections 4
USB 6/7, 8/9 3, 5 Backpanel USB Connections 6/7, 8/9
VGA 8 Backpanel VGA Port
LED Item # Description Color/State Status
LED1 10 Rear UID LED Blue: On Unit Identified
LED2 39 Onboard PWR LED Green: On Power On
LEDM1 15 BMC Heartbeat LED Green BMC Normal
Motherboard Layout and Features Jumpers, Connectors and LED Indicators
Jumpers
Connectors
LED Indicators
CPU Installation Heatsink Installation Front Panel Control (JF1)
1
5
1
9
1
14
1
10
1
15
1
4
1
8
1
13
1
3
1
7
1
12
1
17 1
18
1
19
1
20
1
2
1
6
1
11
1
16
1
21
1
26
1
31
1
36
1
41
1
37 1
42 1
43
1
44 1
45
1
46
1
47
1
48 1
49
1
50
1
51
1
38 1
39 1
40
1
32 1
33
1
34
1
35
1
27
1
28
1
28
1
29
1
30
1
22
1
23
1
24
1
25
1
1
Power Button
Blue+ (OH/Fan Fail/
PWR FaiL/UID LED)
1
NIC1 Link LED
Reset Button
2
Power Fail LED
HDD LED
FP PWRLED
Reset
PWR
3.3 V Stby
3.3V Stby
Red+ (Blue LED Cathode)
Ground
Ground
1920
3.3V Stby
X
Ground NMI
X
NIC2 Link LED 3.3V Stby
3.3V Stby
Note: Item numbers are listed in counterclockwise order.
= mounting hole
OPEN1st
Socket Keys
1.
2.
CPU Keys
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide. Note: Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, and LED indicators.
Insert the desired number of DIMMs into the memory slots, starting with P1-DIMMA1.
For memory to work properly, follow the tables below for memory population order.
Refer to the motherboard layout (at left) for the location of the DIMM slots.
Processors and their Corresponding
Memory Modules
CPU# Corresponding DIMM Modules
CPU1 P1-
DIMMA1 P1-
DIMMB1 P1-
DIMMC1 P1-
DIMMD1
CPU2 P2-
DIMME1 P2-
DIMMF1 P2-
DIMMG1 P2-
DIMMH1
Processor and Memory Module Population
Number of
CPUs+DIMMs CPU and Memory Population Configuration Table
(*For memory to work properly, please install DIMMs in pairs)
1 CPU &
2 DIMMs CPU1
P1-DIMMA1/P1-DIMMB1
1 CPU &
4 DIMMs CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1
2 CPUs &
2 DIMMs CPU1 + CPU2
P1-DIMMA1, P2-DIMME1
2 CPUs &
4 DIMMs CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1
2 CPUs &
6 DIMMs CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1
2 CPUs &
8 DIMMs CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-
DIMMG1/P2-DIMMH1
Back Panel IO Connectors
Memory Support
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
DIMM Installation
OPEN1st
