http://www.supermicro.com MNL-1747-QRG
Board Layout
SuperServer 6038R-TXR Quick Reference Guide
CPU Installation
Beep Codes
Front View & Interface
Heatsink Installation
1. Place heatsink on top of installed CPU
2. Line up the four screws to socket
3. Push down heatsink and screw down as shown
(cross pattern, in order: A, C, B, D)
4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten
each screw, to avoid damaging the system
Memory
Caution
Align CPU to socket;
install CPU straight down
NOTE:
Do not bend pin inside socket
!
Screw #B
Screw #D
Screw #A
Screw #C
SAFETY INFORMATION
IMPORTANT: See installation instructions and safety warning
before connecting system to power supply.
http://www.supermicro.com/about/policies/safety_information.cfm
WARNING:
To reduce risk of electric shock/damage to equipment,
disconnect power from server by disconnecting all power
cords from electrical outlets.
If any CPU socket empty, install protective plastic CPU cap
CAUTION:
Always be sure all power supplies for this system have
the same power output. If mixed power supplies are
installed, the system will not operate.
For more information go to :
http://www.supermicro.com/support
!
!
!
Power Button
Reset Button
Power LED
Device Activity LED
LAN1 LED & LAN2 LED
Information LED
Power Failure LED
Hard Drive Signal
Hard Drive Fail
1
2
3
4
5
6
7
8
9
Description
No.
2 17 4 356
Rear View
9
8
11 Standard PCI Slots
Power Supply Module
1
2
Description
No.
1
2
Top View of DDR4 Slot
Release Tab Release Tab
Note: Notch should align
with the receptive key
point on the slot.
NotchNotch
Front View
Processors and Memory Module Population for Optimal Performance
Number of
CPUs + DIMMs CPU and Memory Population Configuration Table
(For memory to work properly, follow the instructions below)
1 CPU & 2 DIMMs CPU1 & P1-DIMMA1/P1-DIMMB1
1 CPU & 4 DIMMs
1 CPU & 5~8 DIMMs
2 CPUs & 4 DIMMs
2 CPUs & 6 DIMMs
CPU1 & P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1
CPU1 & P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 +
Any memory pairs in P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2 slots
CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1
CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1
2 CPUs & 8 DIMMs
2 CPUs & 10~16 DIMMs
2 CPUs & 16 DIMMs
CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1
CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1
+ Any memory pairs in P1, P2 DIMM slots
CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1,
P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-DIMME2/P2-DIMMF2/P2-DIMMG2/P2-DIMMH2
Processors and their Corresponding Memory Modules
CPU# Corresponding DIMM Modules
CPU 1 P1-DIMMA1
CPU 2 P2-DIMME1
P1-DIMMB1
P2-DIMMF1
P1-DIMMC1
P2-DIMMG1
P1-DIMMD1
P2-DIMMH1
P1-DIMMA2
P2-DIMME2
P1-DIMMB2
P2-DIMMF2
P1-DIMMC2
P2-DIMMG2
P1-DIMMD2
P2-DIMMH2
i
i
BIOS Beep Codes
Beep Code/LED Message Description
1 beep Refresh Circuits have been reset.
(Ready to power up)
5 short beeps + 1 long
beep
Memory
5 long beeps + 2 short
beeps
Display memory
read/write status
Video adapter missing or with
faulty memory
1 continuous beep System System overheat
No memory detected
FANB
COM1
IPMILAN
USB4/5 (3.0)
USB0/1 (2.0)
LAN1
LAN2
CPU2
CPU1
VGA
UID-SW
UID-LED
FANC
BMCFWR
COM2
X10DRX
JIPMB1 JPL1 JPB1 JPG1 JPME2 JWD1
CPU1Slot1 PCI-E 3.0x8
CPU1Slot2 PCI-E 3.0x8
CPU1Slot3 PCI-E 3.0x8
CPU1Slot4 PCI-E 3.0x8
CPU1Slot5 PCI-E 3.0x8
CPU2Slot6 PCI-E 3.0x8
CPU2Slot7 PCI-E 3.0x8
CPU2Slot8 PCI-E 3.0x8
CPU2Slot9 PCI-E 3.0x8
CPU2Slot10 PCI-E 3.0x8
CPU2Slot11 PCI-E 2.0x4 in x8
JPI2C1
P1-DIMMA1
P1-DIMMA2
P1-DIMMB1
P1-DIMMB2
Alwayspopulate DIMM1 first
USB6 (3.0)
TPM/Port80
FrontCTRL Panel
JF1
USB2/3 (2.0)
USB7/8 (3.0)
S-SATA0S-SATA1
S-SATA2
S-SATA3
I-SATA0
I-SATA2
I-SATA1
I-SATA3
I-SATA5
I-SGPIO1
I-SGPIO2
S-SGPIO1
JL1
I-SATA4
FANA
JSD2
JSD1
JBT1
JBAT1
Battery
BIOS
SP1
FAN3
JVR1
FAN2
FAN6
CPU1
FAN1
JPWR1
JPWR2
JPWR3
FAN7
CPU2
P1-DIMMD2
P1-DIMMD1
P1-DIMMC2
P1-DIMMC1
P2-DIMMF2
P2-DIMMF1
P2-DIMME2
P2-DIMME1
P2-DIMMG1
P2-DIMMG2
P2-DIMMH1
P2-DIMMH2
JSTBY1
JI2C1
JI2C2
J23
FAND
FAN4
FAN5
JPWR4
JNVI2C1
JNVI2C2
BMCCTRL LANCTRL
PCH
JTPM1
JUIDB1
LEM1
LED2
LED1
18 17
26
25
Description
No.
CPU1 Slot1 PCI-E 3.0 x8
CPU1 Slot2 PCI-E 3.0 x8
CPU1 Slot3 PCI-E 3.0 x8
CPU1 Slot4 PCI-E 3.0 x8
CPU1 Slot5 PCI-E 3.0 x8
CPU2 Slot6 PCI-E 3.0 x8
CPU2 Slot7 PCI-E 3.0 x8
CPU1 Slot8 PCI-E 3.0 x8
CPU2 Slot9 PCI-E 3.0 x8
CPU2 Slot10 PCI-E 3.0 x8
CPU2 Slot11 PCI-E 2.0 x4 (in x8)
DIMME1(Blue)/DIMME2 slot
DIMMF1 (Blue)/DIMMF2 slot
CPU2 Socket
DIMMH1 (Blue)/DIMMH2 slot
DIMMG1 (Blue)/DIMMG2 slot
DIMMA1 (Blue)/DIMMA2 slot
DIMMB1 (Blue)/DIMMB2 slot
CPU1 (it must be installed on it first)
DIMMD1 (Blue)/DIMMD2 slot
DIMMC1 (Blue)/DIMMC2 slot
JBT1 = Clear CMOS
(S-)SATA 3.0 Ports #0~3
(I-)SATA 2.0 Ports #0~4
JSD1 & JSD2 = SATA Device Power Connector
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
21 20 19
2523
1234 5 614
7 8 9 10 11 12 13 15 16
22
Ranks
per DIMM
&
Data Width
Memory Capacity
Per DIMM (GB)
(See the Note below)
Speed (MT/s) and Voltage Validated by Slot per Channel (SPC) and
DIMM Per Channel (DPC)
2 Slots Per Channel
1DPC
1.2V
4Gb 8Gb
SRx4
SRx8
DRx8
DRx4
8GB 16GB
4GB 8GB
8GB 16GB
16GB 32GB
2133
2133
2133
2133
Populate DIMM Memory Modules
QRx4 32GB 64GB 2133
2133 1866
2133 1866
2133 1866
2133 1866
2133 2133
2DPC
Type
RDIMM
RDIMM
RDIMM
RDIMM
LRDIMM
1 Slot Per Channel
1DPC
Note: For detailed information on memory support and updates, please refer to the SMC
Recommended Memory List posted on our website at http://www.supermicro.com/support/resources/mem.cfm.
3 Slots Per Channel
2133 1866
2133 1866
2133 1866
2133 1866
2133 2133
2DPC
1DPC
1866
1866
1866
1866
2133
3DPC
ÌMNL-1747-QRG6Î
