Supero SuperServer 7046T-H6R User manual

®
SUPERSERVER 7046T-H6R
SUPERSERVER 7046T-H6RF
SUPER
USER’S MANUAL
1.0

Manual Revision 1.0
Release Date: November 3, 2009
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software, if any,
and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or
reduced to any medium or machine without prior written consent.
IN NO EVENT WILLSUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATASTORED OR USED WITH THE PRODUCT, INCLUDINGTHE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for
all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2009 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

iii
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians.
It provides information for the installation and use of the SuperServer 7046T-
H6R/7046T-H6RF. Installation and maintainance should be performed by experi-
enced technicians only.
The SuperServer 7046T-H6R/7046T-H6RF is a high-end tower/4U server based
on the SC745TQ-R800B chassis and the X8DTH-6/X8DTH-6F dual processor
serverboard.
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with
the server system and describes the main features of the X8DTH-6/X8DTH-6F
serverboard and the SC745TQ-R800B chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer 7046T-
H6R/7046T-H6RF into a rack and check out the server configuration prior to pow-
ering up the system. If your server was ordered without processor and memory
components, this chapter will refer you to the appropriate sections of the manual
for their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: System Safety
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 7046T-H6R/7046T-H6RF.

SUPERSERVER 7046T-H6R/7046T-H6RF User's Manual
iv
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X8DTH-6/X8DTH-6F serverboard,
including the locations and functions of connections, headers and jumpers. Refer
to this chapter when adding or removing processors or main memory and when
reconfiguring the serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC745TQ-R800B server chassis.
You should follow the procedures given in this chapter when installing, removing or
reconfiguring SATA or peripheral drives and when replacing system power supply
units and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed informa-
tion on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: System Specifications

Notes
Preface
v

vi
Table of Contents
Chapter 1 Introduction
1-1 Overview .........................................................................................................1-1
1-2 Serverboard Features..................................................................................... 1-2
Processors ......................................................................................................1-2
Memory ...........................................................................................................1-2
SAS ................................................................................................................1-2
Serial ATA ....................................................................................................... 1-2
PCI Expansion Slots....................................................................................... 1-2
Onboard Controllers/Ports .............................................................................. 1-2
Graphics Controller......................................................................................... 1-3
Other Features................................................................................................1-3
1-3 Server Chassis Features ................................................................................ 1-3
System Power................................................................................................. 1-3
Front Control Panel.........................................................................................1-3
I/O Backplane.................................................................................................. 1-3
Cooling System...............................................................................................1-3
1-4 Contacting Supermicro....................................................................................1-5
Chapter 2 Server Installation
2-1 Overview .........................................................................................................2-1
2-2 Unpacking the System.................................................................................... 2-1
2-3 Preparing for Setup.........................................................................................2-1
Choosing a Setup Location............................................................................. 2-2
Rack Precautions............................................................................................ 2-2
Server Precautions..........................................................................................2-2
Rack Mounting Considerations.......................................................................2-3
Ambient Operating Temperature................................................................2-3
Reduced Airflow .........................................................................................2-3
Mechanical Loading ................................................................................... 2-3
Circuit Overloading.....................................................................................2-3
Reliable Ground ......................................................................................... 2-3
2-4 Installing the System into a Rack ...................................................................2-4
Identifying the Sections of the Rack Rails..................................................... 2-4
Installing the Chassis Rails............................................................................. 2-5
Installing the Rack Rails .................................................................................2-6
Installing the Server into the Rack.................................................................. 2-7
2-5 Checking the Serverboard Setup.................................................................... 2-8
SUPERSERVER 7046T-H6R/7046T-H6RF User's Manual

vii
2-6 Checking the Drive Bay Setup........................................................................ 2-9
Chapter 3 System Interface
3-1 Overview .........................................................................................................3-1
3-2 Control Panel Buttons..................................................................................... 3-1
Power..............................................................................................................3-1
Reset...............................................................................................................3-1
3-3 Control Panel LEDs ........................................................................................3-2
Power..............................................................................................................3-2
HDD................................................................................................................. 3-2
NIC1................................................................................................................3-2
NIC2................................................................................................................3-2
Overheat/Fan Fail ........................................................................................... 3-3
Power Fail.......................................................................................................3-3
3-4 Drive Carrier LEDs.........................................................................................3-3
Chapter 4 System Safety
4-1 Electrical Safety Precautions..........................................................................4-1
4-2 General Safety Precautions............................................................................ 4-2
4-3 ESD Precautions.............................................................................................4-3
4-4 Operating Precautions .................................................................................... 4-4
Chapter 5 Advanced Serverboard Setup
5-1 Handling the Serverboard............................................................................... 5-1
Precautions .....................................................................................................5-1
Unpacking .......................................................................................................5-2
5-2 Serverboard Installation.................................................................................. 5-2
5-3 Connecting Cables..........................................................................................5-3
Connecting Data Cables................................................................................. 5-3
Connecting Power Cables .............................................................................. 5-3
Connecting the Control Panel......................................................................... 5-3
5-4 I/O Ports..........................................................................................................5-4
5-5 Installing a Processor and Heatsink ...............................................................5-5
Installing an LGA1366 Processor ...................................................................5-5
Installing a CPU Heatsink............................................................................... 5-7
5-6 Installing Memory............................................................................................5-8
Memory Support..............................................................................................5-8
DIMM Installation ............................................................................................ 5-8
Populating DIMMs...................................................................................... 5-9
5-7 Installing PCI Expansion Cards ....................................................................5-10
5-8 Serverboard Details .......................................................................................5-11
Table of Contents

viii
X8DTH-6F/X8DTH-6 Quick Reference......................................................... 5-12
5-9 Connector Definitions ...................................................................................5-13
5-10 Jumper Settings............................................................................................ 5-18
5-11 Onboard Indicators........................................................................................ 5-20
5-12 SAS and SATA Ports..................................................................................... 5-21
5-13 Installing Software.........................................................................................5-22
Supero Doctor III...........................................................................................5-23
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices..................................................................................6-1
Precautions .....................................................................................................6-1
6-2 Front Control Panel.........................................................................................6-3
6-3 System Fans................................................................................................... 6-4
Fan Failure......................................................................................................6-4
6-4 Drive Bay Installation...................................................................................... 6-6
SAS Drives......................................................................................................6-6
SAS Backplane............................................................................................... 6-7
Storage Module...............................................................................................6-9
Adding Drives to the Storage Module......................................................6-10
Using a Mobile Rack..................................................................................... 6-10
6-5 Power Supply.................................................................................................6-11
Power Supply Failure.....................................................................................6-11
Removing/Replacing the Power Supply.........................................................6-11
Chapter 7 BIOS
7-1 Introduction...................................................................................................... 7-1
Starting BIOS Setup Utility..............................................................................7-1
How To Change the Configuration Data......................................................... 7-1
Starting the Setup Utility................................................................................. 7-2
7-2 Main Setup...................................................................................................... 7-2
7-3 Advanced Setup Configurations......................................................................7-4
7-4 Security Settings........................................................................................... 7-24
7-5 Boot Configuration ........................................................................................ 7-26
7-6 Exit Options...................................................................................................7-27
Appendix A BIOS Error Beep Codes
Appendix B System Specifications
SUPERSERVER 7046T-H6R/7046T-H6RF User's Manual

Chapter 1
Introduction
1-1 Overview
The SuperServer 7046T-H6R/7046T-H6RF is a high-end server comprised of
two main subsystems: the SC745TQ-R800B server chassis and the X8DTH-6/
X8DTH-6F dual processor serverboard. Please refer to our web site for informa-
tion on operating systems that have been certified for use with the system (www.
supermicro.com).
In addition to the serverboard and chassis, various hardware components have
been included with the 7046T-H6R/7046T-H6RF, as listed below:
Two passive heatsinks (SNK-P0038P)
•
Three 8-cm chassis fans (FAN-0074L4)•
Two exhaust fans (FAN-0082L4)•
One air shroud (MCP-310-48001-0N)•
SATA Accessories•
One SATA backplane (CSE-SAS-743TQ)
One iPass to SATA cable (CBL-0118L-02)
Two 40-cm SGPIO cables (CBL-0157L)
Eight drive carriers (CSE-PT17-B)
One rackmount kit, optional (CSE-PT26)
•
One CD containing drivers and utilities•
SuperServer 7046T-H6R/7046T-H6RF User's Manual•
Chapter 1: Introduction
1-1

1-2
SUPERSERVER 7046T-H6R/7046T-H6RF User's Manual
1-2 Serverboard Features
The SuperServer 7046T-H6R/7046T-H6RF is built upon the X8DTH-6/X8DTH-6F,
a dual processor serverboard based on the Intel 5520 chipset and including two
IOH36D hubs. Below are the main features of the X8DTH-6/X8DTH-6F. (See Figure
1-1 for a block diagram of the chipset).
Processors
The X8DTH-6/X8DTH-6F supports single or dual Intel® Xeon® 5500 LGA 1366
processors. Please refer to the serverboard description pages on our web site for
a complete listing of supported processors (www.supermicro.com).
Memory
The X8DTH-6/X8DTH-6F has twelve DIMM slots that can support up to 96 GB of
registered ECC or up to 24 GB of unbuffered ECC/non-ECC DDR3-1333/1066/800
SDRAM. The memory operates in a 3-channel configuration and requires modules
of the same size and speed to be installed three at a time. See Chapter 5 for
details.
SAS
An LSI2008 controller chip is integrated into the serverboard to provide an eight-
port SAS subsystem.
Serial ATA
A Serial ATA controller is integrated into the ICH10R (South Bridge) portion of the
IOH-36D chipset to provide a six-port 3 Gb/s SATA subsystem, which is RAID 0,
1, 10 and 5 supported (RAID 5 supported by Windows OS only). The SATA drives
are hot-swappable units.
PCI Expansion Slots
The X8DTH-6/X8DTH-6F has seven PCI Express 2.0 x8 slots (all in x16 slots).
Onboard Controllers/Ports
The color-coded I/O ports include one COM port (an additional COM header is lo-
cated on the serverboard), a VGA (monitor) port, two USB 2.0 ports (two additional
USB headers and one Type A port are included on the serverboard), PS/2 mouse
and keyboard ports and two gigabit Ethernet ports. In addition, the X8DTH-6F
(7046T-H6RF) includes a dedicated IPMI LAN with KVM support.

1-3
Chapter 1: Introduction
Graphics Controller
The X8DTH-6/X8DTH-6F features an integrated Matrox G200eW graphics chip,
which includes 16 MB of DDR2 memory.
Other Features
Other onboard features that promote system health include onboard voltage moni-
tors, a chassis intrusion header, auto-switching voltage regulators, chassis and CPU
overheat sensors, virus protection and BIOS rescue.
1-3 Server Chassis Features
The following is a general outline of the main features of the SC745TQ-R800B
server chassis.
System Power
The SC745TQ-R800B features a redundant 800W power supply composed of two
separate power modules. This power redundancy feature allows you to replace a
failed power supply without shutting down the system.
Front Control Panel
The control panel on the SuperServer 7046T-H6R/7046T-H6RF provides you with
system monitoring and control. LEDs indicate system power, HDD activity, network
activity, system overheat and power supply failure. A main power button and a
system reset button are also included. In addition, two USB ports have been incor-
porated into the control panel to provide front side USB access.
I/O Backplane
The SC745TQ-R800B is an Extended ATX form factor chassis that may be used in
either a tower or a 4U rackmount configuration. The I/O backplane provides seven
tool-less motherboard expansion slots, one COM port, one parallel port, one VGA
port, two USB 2.0 ports, PS/2 mouse and keyboard ports and two gigabit Ethernet
ports. The 7046T-H6RF also includes a dedicated IPMI LAN
Cooling System
The chassis has an innovative cooling design that includes three 8-cm hot-plug
system cooling fans located in the middle section of the chassis as well as two 8-cm
hot-plug exhaust fans located at the rear of the chassis. An air shroud channels the

1-4
SUPERSERVER 7046T-H6R/7046T-H6RF User's Manual
Figure 1-1. Intel 5520/ICH10R Chipset:
System Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.
airflow from the system fans to efficiently cool the processor area of the system.
The power supply module also includes a cooling fan.
#4
#5
USB2.0
SATA2
Ports 5&6
ICH10R
ESI
BIOS
BMC
QPI
SATA
#0
#1
#2
#3
QPI
QPI
QPI
PCI-E x8
PCI-E x8
PCI-E x8
PCI-E x8
LSI 2008
ESI
Ports 7&8
Ports 9&10
Ports 3&4
Ports 5&6
Ports 9&10
USB
PCI 33MHz
SIO
W83527HG
LPC BUS
6 FRONT
SPI
WPCM450
U3H1
CPU#2 CPU#1
ESI x4
800/1066/1333
DDR3
#1-4
#1-3
#1-2
#1-1
#1-5
#1-6 #0-5
#0-6
800/1066/1333
#0-4
#0-3
#0-2
#0-1
DDR3
6Gb/s SAS
0, 1, 2, 3
4, 5, 6, 7
Ports 7&8
PCI-E x8
PCI-E x8
PCI-E x8
PCI-E x8
#7
#6
#5
PCI-E x8 in x16 Slot
#4
Ports 3&4
#1
#3
#2
Ports 1&2
2 REAR + 4 FRONT + 1 TYPE A
USB
RMII_IPMI
Intel 82576
LAN1
LAN2
LAN
PCI-E x4
Ports 1&2
KB
MS
VGA
DDR II
RTL8201N
LAN3
IPMI_LAN RMII
IPMI
00
0
1
PCI-E x8 in x16 Slot
PCI-E x8 in x16 Slot
PCI-E x8 in x16 Slot
PCI-E x8 in x16 Slot
PCI-E x8 in x16 Slot
PCI-E x8 in x16 Slot
COM1
External
IOH1-36D
Intel 5520
Intel
(5500 Series) (5500 Series)
IOH2-36D
Intel 5520

1-5
Chapter 1: Introduction
1-4 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Asia-Pacific
Address: Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [email protected]
Tel: [phone], ext.132 or 139

1-6
SUPERSERVER 7046T-H6R/7046T-H6RF User's Manual
Notes

Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer 7046T-
H6R/7046T-H6RF up and running. Following these steps in the order given should
enable you to have the system operational within a minimum amount of time.
This quick setup assumes that your system has come to you with the proces-
sors and memory preinstalled. If your system is not already fully integrated with a
serverboard, processors, system memory etc., please turn to the chapter or section
noted in each step for details on installing specific components.
The 7046T-H6R/7046T-H6RF may be employed either as a tower or mounted in a
rack as a 4U rackmount chassis. If using it as a tower unit, please read the Server
Precautions in the next section and then skip ahead to Section 2-5.
2-2 Unpacking the System
You should inspect the box the system was shipped in and note if it was damaged
in any way. If the server itself shows damage you should file a damage claim with
the carrier who delivered it.
Decide on a suitable location for the SuperServer 7046T-H6R/7046T-H6RF. It
should be situated in a clean, dust-free area that is well ventilated. Avoid areas
where heat, electrical noise and electromagnetic fields are generated. You will also
need it placed near a grounded power outlet. Be sure to read the Rack and Server
Precautions in the next section.
2-3 Preparing for Setup
The box the system was shipped in may include two sets of rail assemblies, two
rail mounting brackets and mounting screws needed for installing the system into a
rack (optional kit). Follow the steps in the order given to complete the installation
process in a minimum amount of time. Please read this section in its entirety before
you begin the installation procedure outlined in the sections that follow.

2-2
SUPERSERVER 7046T-H6R/7046T-H6RF User's Manual
!
!
Warnings and Precautions!
Choosing a Setup Location
Leave enough clearance in front of the rack to enable you to open the front door•
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufficient airflow and ease in servicing.
This product is not suitable for use with visual display work place devices
•
acccording to §2 of the the German Ordinance for Work with Visual Display
Units.
Rack Precautions
Ensure that the leveling jacks on the bottom of the rack are fully extended to•
the floor with the full weight of the rack resting on them.
In single rack installation, stabilizers should be attached to the rack. In multiple
•
rack installations, the racks should be coupled together.
Always make sure the rack is stable before extending a component from the
•
rack.
You should extend only one component at a time - extending two or more si-
•
multaneously may cause the rack to become unstable.
Slide/rail-mounted equipment is not to be used as a shelf or workspace.
•
Server Precautions
Review the electrical and general safety precautions in Chapter 4.•
Determine the placement of each component in the rack• before you install the
rails.
Install the heaviest server components on the bottom of the rack first, and then
•
work up.
Use a regulating uninterruptible power supply (UPS) to protect the server from
•
power surges, voltage spikes and to keep your system operating in case of a
power failure.

Chapter 2: Server Installation
2-3
Allow the hot plug SATAdrives and power supply modules to cool before touch-•
ing them.
Always keep the rack's front door and all panels and components on the servers
•
closed when not servicing to maintain proper cooling.
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating tempera-
ture of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient tempera-
ture (Tmra).
Reduced Airflow
Equipment should be mounted into a rack so that the amount of airflow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec-
tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).

2-4
SUPERSERVER 7046T-H6R/7046T-H6RF User's Manual
2-4 Installing the System into a Rack
This section provides information on installing the system into a rack unit. Rack
installation requires the use of the optional rackmount kit. If the system has already
been mounted into a rack or if you are using it as a tower, you can skip ahead to
Sections 2-5 and 2-6.
There are a variety of rack units on the market, which may mean the assembly
procedure will differ slightly. The following is a guideline for installing the server into
a rack with the rack rails provided in the rackmount kit. You should also refer to the
installation instructions that came with the rack unit you are using.
Identifying the Sections of the Rack Rails
The optional rackmount kit includes two rack rail assemblies. Each of these as-
semblies consist of three sections: an inner fixed chassis rail that secures to the
chassis, an outer rack rail that secures directly to the rack itself and two rail brackets,
which also attack to the rack (see Figure 2-1.) The inner and outer rails must be
detached from each other to install.
To remove the inner chassis rail, pull it out as far as possible - you should hear a
"click" sound as a locking tab emerges from inside the rail assembly and locks the
inner rail. Depress the locking tab to pull the inner rail completely out. Do this for
both assemblies (one for each side).
Figure 2-1. Identifying the Sections of the Rack Rails
Inner rail
Outer rail
Rail brackets

Chapter 2: Server Installation
2-5
Installing the Chassis Rails
You will need to remove the top cover and the feet to add rack rails to the chassis.
First, remove the top and right covers (top and left covers when standing as a tower
chassis) by first removing the screws that secure them to the chassis. Depress the
button on the top (side if tower) of the chassis to release the cover and then pull
the cover off. Then unscrew the four feet and remove them from the chassis (see
Figure 2-2).
You can now attach rack rails to the top and bottom (now the sides) of the chassis.
First add the rack handles. Then position the inner chassis rail sections you just
removed along the side of the chassis making sure the screw holes line up. Note
that these two rails are left/right specific. Screw the rail securely to the side of the
chassis (see Figure 2-3). Repeat this procedure for the other rail on the other side
of the chassis. You will also need to attach the rail brackets when installing into a
telco rack.
Locking Tabs: As mentioned, the chassis rails have a locking tab, which serves
two functions. The first is to lock the server into place when installed and pushed
fully into the rack, which is its normal position. Secondly, these tabs also lock the
server in place when fully extended from the rack. This prevents the server from
coming completely out of the rack when you pull it out for servicing.
Figure 2-2. Preparing to Install the Chassis Rails

2-6
SUPERSERVER 7046T-H6R/7046T-H6RF User's Manual
Installing the Rack Rails
Determine where you want to place the SuperServer 7046T-H6R/7046T-H6RF in
the rack. (See Rack and Server Precautions in Section 2-3.) Position the fixed
rack rail/sliding rail guide assemblies at the desired location in the rack, keeping
the sliding rail guide facing the inside of the rack. Screw the assembly securely to
the rack using the brackets provided. Attach the other assembly to the other side
of the rack, making sure both are at the exact same height and with the rail guides
facing inward.
Figure 2-3. Installing the Rails to the Chassis