Surebonder 9755 User manual

®
FPC Corporation - 355 Hollow Hill Drive - Wauconda, IL 60084
Phone: [phone] Fax: [phone]
website: www.surebonder.com e-mail: [email protected]
Read All Safety Rules and Instructions Carefully
Save this manual for Future Reference
1211
Operating Instructions
2-1/2" 16 gauge Straight Finish Nailer
Includes: 2 Allen wrenches & pneumatic tool oil
Model 9755 2-1/2" Finish Nailer
WARRANTY
If you have any problems with this tool, please call FPC Corporation toll-free at
1-800-860-3838 before returning it to the place of purchase.
FPC Corporation warrants this product to be free from defects in material and
workmanship, under normal conditions of use and when used in accordance with
FPC operating instructions, for a period of 90 days from the date of purchase by the
user. Within the 90 day warranty FPC at its option shall repair or replace the
product. . The product must be returned at the distributor/user expense, either
within warranty or out. Repaired or replaced products will receive a 60 day
warranty. USER MUST BE USING THE PROPER NAILS FOR THIS WARRANTY TO
BE VALID. WARRANTY IS VOID IF INCORRECT TYPE OF NAILS ARE USED.
®
Visit us at surebonder.com for our full line of products

THE SAFETY WARNINGS BELOW CANNOT COVER ALL POSSIBLE SITUATIONS THAT MAY
OCCUR. THESE BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO PROTECT
AGAINST PERSONAL INJURY TO THE OPERATOR OR OTHER PERSONNEL IN THE AREA, AS
WELL AS DAMAGE TO THE EQUIPMENT. READ AND UNDERSTAND THESE WARNINGS BEFORE
USING EQUIPMENT.
Keep tool away from children, and DO NOT allow children near work area. Do not allow children
or untrained personnel to handle this nailer.
DO NOT operate this nailer while tired, or under the influence of drugs, alcohol, or medication
that makes you drowsy.
Never point the nailer at yourself or others - always assume that the nailer is loaded, and
proceed with caution.
Wear safety glasses and ear protection. The nailer operator and all personnel in the work area
must wear safety glasses that protect the front and side, to avoid eye injury. Ear plugs should be
worn to avoid hearing damage.
If operator will be working in a situation where overhead work will be done (i.e. on a ladder,
stairs, or scaffolding) a hard hat must be worn.
Never wear loose clothing or jewelry because it can get caught in the moving parts of this nailer.
Make sure long hair is covered, to avoid getting it caught in nailer.
Keep the nailer pointed away from yourself and others at all times. Keep hands and all body parts
away from rear area of nailer (near air hose) to guard against injury. Keep hands and feet away
from firing head during use.
Keep proper balance and footing at all times - do not over-reach.
Never use oxygen, bottled gas or any type of combustible fuel as a power source - it can cause
an explosion and serious injury.
Do not use near flammable liquids or gases - the stapler sparks during operation, and could
cause an explosion and serious injury.
Use an air hose that will withstand at least 150 psi, OR 150% of the maximum pressure of the
compressor.
Never connect this tool to compressed air if the pressure could exceed 200 psi, as the nailer
could burst. Use only clean, dry, regulated compressed air, with pressure not exceeding 120 psi.
Do not use a non-relieving coupler with this nailer - if used, the nailer could remain charged with
air after disconnecting, and would still be able to drive a nail even after being disconnected. The
nailer and air hose must have a coupling so that all pressure is removed from the nailer when the
coupling is disconnected.
Do not depress the trigger or safety mechanism while loading nails - accidental firing of a nail
can occur. Keep your fingers away from the trigger when not firing nails. Always keep the nailer
pointed downward during loading.
Do not use an air hose that is too long - nailer operator can trip over it. Make sure all connections
are tight.
(WARNINGS continued next page)
Improper use of this nailer can result in death or serious injury.
This manual contains important information about product safety.
Read and understand this entire manual before operating this nailer.
IMPORTANT SAFETY WARNINGS:
! DANGER
1
10
To order go to: www.surebonder.com

Disconnect air hose from nailer:
before performing maintenance.
when clearing a jam.
when tool is not in use.
when moving it to another location.
when handing nailer to another person.
DO NOT place finger on trigger when disconnecting air hose - the nailer could fire when
reconnected to the air supply.
Carry nailer by the handle only, not by the air hose.
Do not drive nails close to the edge of the workpiece. It could split, allowing a nail to fly
or ricochet and causing personal injury. Do not try to drive nails at too steep an angle.
Make sure nailer is held firmly during firing to minimize recoil.
Do not drive a nail into very hard material, thin material, or on top of an existing nail- the
nail could ricochet, causing personal injury.
Never use the nailer if it is leaking air, the contact safety mechanism is not working,
nailer has missing or damaged parts, or requires repair. Make sure all screws and caps
are securely tightened.
Inspect the nailer before each use to insure that the trigger, safety mechanism, and
spring are operating properly. Lock the nailer in a clean, dry storage area between uses.
Only use parts, nails, and accessories supplied or recommended by FPC Corporation.
Unauthorized parts or fasteners can lead to malfunction and serious injury. Only
personnel trained by FPC Corporation or the distributor shall repair the nailer. Do not
modify this tool in any way.
Never use in presence of flammable liquids or gases. The nailer produces sparks during
operation.
Never use the nailer in sites containing lacquer, paint, benzine, thinner, gasoline, gases,
adhesive agents, and other materials which are combustible or explosive.
Check for live wires. Avoid the risk of electrical shock by checking for live wires that may
be hidden by walls, floors, or ceilings. Turn off the breaker switch pertaining to that work
area.
Do not store the nailer in a cold weather environment.. Keep the nailer in a warm area
until the start of work. If it is in a cold area, bring it in a warm area and allow it to warm
up before use.
Manufacturer assumes no responsibility for consequential or indirect damages from the
use of this product.
Save this manual and have it available for tool operators
reference!
IMPORTANT SAFETY WARNINGS: continued
California Proposition 65
You can create dust when you cut, sand, drill or grind materials such as: wood,
paint, metal, concrete, cement, or other masonry. This dust often contains chemicals
known to cause cancer, birth defects or other reproductive harm. Wear protective gear.
92

Troubleshooting
The following form lists the common operating system with problems and solutions. Please read
the form carefully and follow it.
WARNING: If any of the following symptoms appears during your operation, stop using the tool
immediately, or serious personal injury could result. Only qualified persons or an authorized service
center can perform repairs or replacement of tool. Disconnect tool from air supply before
attempting repair or adjustment. When replacing O-rings or cylinder, lubricate with air tool oil
before assembly.
Problem
Nailer operates but no nail is
driven.
Week drive. Slow to cycle.
Drives too deep.
Skipping nails, Intermittent
feed.
Nails jam, Driven nail is bent
Drives properly at normal
speed but does not drive fully
drive at faster nailing speed.
Check
Check for jam
Check feeder function
Ribbon spring damaged or week?
Check for proper nails
Check air pressure
Drive blade worn?
Piston O-ring worn or damaged?
Check air pressure.
Check for proper nails.
Check nail feeder function
Ribbon spring worn or damaged?
Piston O-ring cut or worn out?
Check for proper nails.
Drive blade worn?
Check inside hose diameter.
Correction
Clear a nail jam.
Clean and lubricate.
Replace ribbon spring.
Use correct nails.
Increase air pressure. Do not exceed
120 psi.
Use pneumatic oil.
Purchase Drive Pin Kit #9755-410
Purchase Seal Kit #9755-400
Reduce air pressure 70-100 psi.
Use only recommended nails.
Clean and lubricate.
Replace ribbon spring.
Use pneumatic oil.
Purchase Seal Kit #9755-400
Use only recommended nails.
Purchase Drive Pin Kit #9755-410
Use larger air hose.
38
APPLICATIONS
Including but not limited to: Casing, Cabinets, Trim, Furniture Repair, Baseboard, Chair Rail.
FEATURES
- Adjustable Exhaust
- Soft Grip handle reduces fatigue
- Contact safety mechanism - for safe operation
- Protective tip prevents surface damage
- Fast easy loading
AIR SUPPLY
NEVER use oxygen or other bottled gases. Explosion may occur.
This nailer is designed to operate on clean, dry, regulated compressed air, between 60 and 120
psi. It is preferable to include an air filter, pressure regulator, and automatic oiler within 15 feet
of the tool, if possible.
An air filter is needed to remove contaminates and moisture that are contained in compressed
air; filtering will significantly prolong the life of the tool. If an automatic oiler is not installed,
place 2 to 3 drops of oil into the tool's air inlet twice a day. Do not install a quick coupler
directly into the tool. Higher pressure drastically reduces tool life.
The nailer comes factory-equipped with a male quick connector. The nailer must always be
connected to the air supply with a coupling that removes all pressure when it is disconnected.
NOTE: all components used with this nailer (air hose, connectors, regulators, filters, etc) must
be rated at 120 psi, OR 120% of the maximum compressor potential, whichever is higher. Do
not connect this nailer to a system with maximum potential air pressure greater than 200 psi.
! DANGER
20
0
40
60 80100
120
140
160
Lubricator Regulator Filter
To compressor
To Nailer Quick Connector Quick Coupler
AIR CONNECTION SET UP

SPECIFICATIONS
Overall Dimensions: 11.25" x 11.75" x 2.75”
Capacity: 100 nails
Nail Length: 32 mm- 64 mm (1-1/4”-2-1/2”)
Nail size: 16 Gauge(1.60x1.40mm)
Operating Pressure: 60 - 100 PSI (4-7 bar)
Air Inlet Size: 1 /4” N .P.T
Weight of Tool: 4.14 lbs.
NAIL SELECTION
Use SUREBONDER 500 Series
16 gauge straight finish nails
1-1/4" to 2-1/2".
1/4” Male Quick
Release Connector
Trigger
Rubber Grip
Nail magazine
Nail feeder
Contact Safety Mechanism
Rubber Tip
Adjustable
Exhaust Cover
OPERATION
®
min. 1-1/4" (32 mm)
max. 2-1/2 "(64 mm)
Min Max
5
Loading Nails (continued)
To load:
Insert strip of nails into rear of magazine. Do not load with contact safety mechanism or trigger
depressed. Slide nail strip towards the front of the magazine, making sure strip is past the nail stop.
Pull feeder shoe completely behind the nail strip. Release the feeder and the nail strip will be pushed
to the front of the magazine.
Latch
To remove fasteners: Depress the latch and release the feeder shoe and slide it forward. Remove
fasteners from the tool.
Jam Clearing Depth Adjustment Exhaust Deflector Exhaust
Pull down on latch and swing Using thumb screw to achieve deflector can be positioned to
guide plate outward. Remove desired depth. point in any 360° direction.
jammed nail , replace guide Reposition deflector by
plate catch and lift latch up. rotating to the desired
position.
Nails Loaded
Feeder
Nail stop
16
Gauge