Surefire Tower 100 User manual

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 Revised 04/13/2016
Tower 100 Electric Pump System
for NutriSphere-N® NH3
396-3053Y1
AFS Pro 700
AccuControl
SureFire Ag Systems

SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 Revised 04/13/2016
Table Of Contents
A
Introduction
Introduction
 Read Me First......................................................................................... 2
 Basic Steps to Install your System ......................................................... 3
 System Overview Drawing .....................................................................4
B
Components
Liquid
Components - Liquid
 Flowmeter, Electric Shutoff and Section Valves ..................................... 5,6
 Pressure Sensor, Pump Priming and Air Bleed Valve............................ 7
 Flow Indicators and Manifolds ................................................................ 8,10
 Dual Check Valve Systems, Metering Tube, Row Distribution ............... 10-11
 Plumbing Setup, Shank and Knife Points ............................................... 11-12
 Toolbox (Spare Parts) ............................................................................ 13
D
Components
Wiring & Elec.
Components - Wiring & Electrical
 Connecting to Pro 700 AccuControl with Field-IQ Module......................14-15
 System Layout........................................................................................16
 PWM EPD ..............................................................................................17
 Wiring Harness Drawings .......................................................................18-20
E
Installation
Overview
Installation Overview
 Harness Connections, ZIP Valve Mounting ............................................ 21
 Tower 100 Plumbing Overview and Valve Operation, Recirculation ...... 22
 Tower 100 Plumbing Detail .................................................................... 23
 Tower 100 Tank Cradle and Mounting Brackets .................................... 24
F
Setup &
Operation
Controller Setup & Operation
 Pro 700 Display General Setup...............................................................25-26
 AccuControl Configuration ......................................................................27-28
 Create a Layout, Valve Calibration .........................................................29
 Product Setup, Layer Assignment, Work Condition > Control.................30
 Setup Screenshots—Run Screen, Valve Cal, Liquid Drive Setup, more.31
H
Maintenance
& Parts
Maintenance & Parts
 Winterization and Maintenance Recommendations............................... 41
 Pre-season Service ................................................................................ 41
G
Trouble-
Shooting
Troubleshooting
 FAQs, Operating Tips, Troubleshooting Tips..........................................32-34
 Row Flow and Pump Output Chart .........................................................34
 Pump Will Not Run, Flowmeter Not Reading..........................................35-36
 Important Setup and Troubleshooting Procedures ...........................37
 Troubleshooting Pump, PWM, and Section Valves ...............................38-39
 Application Rate fluctuates, Slow Getting to Target Rate .......................40
©2015-2016 SureFire Ag Systems
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 2 Revised 04/13/2016
Read Me First
The SureFire Catalyst™ system is designed to give accurate and even row-to-row distribution of
NutriSphere-N NH3 at a normal rate of 32 oz/acre. It has the capacity to deliver higher rates if desired.
Note: Ounces/acre, not gallons/acre.
Ounces per acre means a very small amount of liquid is being pumped and distributed. At 6 mph on 30” row
spacing, a rate of 32 oz/acre means that each row has a flow of just under 1 oz/min. On a 12-row implement,
the total amount being pumped, therefore, is less than 12 oz/min. The SureFire Catalyst™ system is
engineered to accurately and evenly distribute this flow.
Low Flow Electromagnetic Flowmeter
The SureFire Catalyst™ system utilizes an electromagnetic flowmeter (with no moving parts) that is
designed and built to accurately measure flows down to 10 oz/min. (The flowmeter is rated down to 10 oz/
min.) SureFire has proven the reliability and accuracy of the electromagnetic flowmeter by years of use in the
field with thousands of flowmeters.
Dual Metering Tube Distribution
The low flow to each row will be evenly distributed through metering tubes that have an opening of 0.080” in
diameter. An orifice that could distribute this flow would be 0.015” or less in diameter. An orifice of that size is
easy to plug. The 4 to 5 times larger diameter of the tube greatly reduces the risks of plugging.
The use of two tubes to each row (dual tube system) means that this system has the ability to handle a wide
variation of rates and speeds (from 5 to 10 mph) and to do this under a wide range of temperature changes
where the viscosity of the product changes.
Flow Indicators
The flow for each row will pass through a flow indicator that has a ball that will float to indicate flow to that row.
This will give an immediate visual indication of flow to each row. While the flow indicators give a good
indication of the flow to each row, they are not always an indicator of the exact flow to each row. Only a catch
test will verify the evenness of the row-to-row distribution.
Tool Box
Each Catalyst™ system comes with a built-in tool box that contains mission-critical spare parts to reduce
equipment downtime.
Product Tank
The Catalyst™ comes with either a 55 gallon or a 110 gallon tank. The large tank would allow over 400
acres of application at the 32 oz/acre rate.
Rinse Tank
Each system comes with a 3-gallon rinse tank that can be filled with RV anti-freeze to allow the system to be
flushed when it will not be used for a few days and to be protected from freezing after the rinse.
Electric Section Valves
Implements that are 60’ wide or wider can be split into 2 sections to allow section control. Standard single
section setups are equipped with electric row-shutoff valves on each flow indicator manifold set. Two-section
systems will have the same manifold shutoff valves but can be configured so the valves on the left half of the
implement will function as Section 1 and the valves on the right half as Section 2.
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 3 Revised 04/13/2016
Getting Started
This manual contains the information for the SureFire Tower 100 system for NutriSphere-N
NH3 that is being introduced in June, 2015.
Changes to components or configuration settings may be made to improve the operation of
the system.
Go to the tab in Section F for the instructions on setting up your display.
You have purchased a SureFire NutriSphere NH3 application system for your equipment. This system can
be controlled by:
 John Deere Rate Controller
 Ag Leader Liquid Product Control Module
 Trimble Field-IQ Rate and Section Control Module
 Case IH Pro 700 with AccuControl
 SureFire Commander II controller
Note: SureFire Ag Systems also has the SureFire Torpedo system, a complete anhydrous ammonia
application system. See www.surefireag.com for more information.
A
Introduction
Basic Installation Steps
1. Have your control module and display in the cab connected and set up by the dealer for your display and
controller. To apply anhydrous ammonia and NutriSphere-N NH3 you will need 2 Field-IQ modules, one
for each product.
2. Open the packages and familiarize yourself with the components. See the System Overview Examples
on the following pages to see the big picture of how SureFire Fertilizer Systems are installed. Refer to
manual sections B & D for component information.
3. Mount the Tower and tank on your equipment.
4. Install the plumbing kit including flow indicator columns, electric ZIP valves, and metering tube plumbing
to each row unit delivery point. See sections B & E for information on these components.
5. Attach harnesses as shown in Section D.
6. Setup Controller for SureFire fertilizer system as shown in Section F.
7. Fill system with water, conduct initial operation and tests per Section F.
8. Winterize system with RV Antifreeze if freezing temperatures are expected.
General Information
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 4 Revised 04/13/2016
System Overview - Example 1
The following gives a layout of the SureFire Tower 100 system with these components:
 Controller display in cab
 Field-IQ module
 Tower 100
 Flow Indicators
 Dual check valves with purple and gray metering tube
A
Introduction
Tractor
Battery
12 Volt
SureFire Adapter Harness– 201-215464Y4
(connector detail in Section D)
PWM Pump Harness (207-215223Y2)
(connector detail in Section D)
Plugs into flowmeter, EPD PWM signal,
section valve(s) and pressure
Field-IQ
module
Display in
cab
EPD Power
Cable
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 5 Revised 04/13/2016
Electromagnetic Flowmeter
204-01-4621CUF05
0.08 to 1.6 GPM (10 oz/min to 205 oz/min)
B
Components
Liquid
Mounting Bracket,
Used in Tower 100
410-2106Y1-BK
Electromagnetic flowmeters are superior to traditional turbine flowmeters in two basic ways. First,
they have no moving parts. This translates into no wear items or potential for contaminants to jam a spinning
turbine.
Second, electromagnetic flowmeters detect the flow by electrically measuring the velocity of the liquid,
which makes them independent of viscosity or density of the fluid measured. They are extremely accurate
using the standard calibration number. SureFire still recommends you perform a catch test to verify the
system is properly installed and configured.
Air causes erratic readings in flowmeters. Be sure all connections from the tank to the flowmeter are tight.
Fittings may not show leaks, but still may be drawing in air that can cause system problems.
This flowmeter will accurately measure flows down to 8 oz/min. Below that rate, the flowmeter may not give a
continuous pulse output.
Caution: Before welding on the implement, disconnect the flowmeter or damage to the
flowmeter electronics may occur.
Do not power wash the flowmeter. High pressure spray directed at the back edge of the face
plate or at the wire connector may allow water into the flowmeter electronics.
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 6 Revised 04/13/2016
Section Valves and Flow Indicator Manifold Shutoff Valves
ZIP Valves
ZIP valve on right shown
with both electrical
connectors plugged (if
daisy-chaining from one
to the next).
Outlets can be plumbed
with a variety of fittings
depending on the
particular scenario.
Flow Indicator Manifold Shutoff Valves
Single-section systems will have electric shutoff valves (ZIP Valves) on each bank of flow indicators. These
valves will be controlled by the Section 1 Connector. A 4’ Y Adapter Cable (201-215604) will be plugged into
the Section 1 connector on the Pump harness (200-03-18220). One end of the Y will connect to the valves on
the left side of the machine, the other end of the Y will connect to the valves on the right side of the machine.
Section Control
Some systems (60 ft. and wider) may be set up as 2-section implements, so half of the applicator can be shut
off in an overlap situation.
These systems will still have the flow indicator shutoff valves, but the valves on the left half of the machine
will be plugged into the Section 1 connector on the harness and the
valves on the right half of the machine will be plugged into the Section
2 connector.
Implements less than 60 feet wide need to be configured as one
section for the NutriSphere N-NH3 product, since the output for
narrower sections will drop below the range of the flowmeter at lower
speeds.
3-Pin Wiring Connector:
Pin A—Red, 12 Volts +
Pin B—Black, Ground -
Pin C—White, Signal
12V=on ; 0V=off
B
Components
Liquid
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 7 Revised 04/13/2016
The Pro 700 with AccuControl currently does not support the use of a liquid pressure
sensor.
The kit for the Pro 700 system includes a pressure gauge. A
pressure reading is helpful troubleshooting information and helps in selecting which
metering tube to use.
Pressure Sensor B
Components
Liquid
Pressure Sensor (3 wire
type) with harness
521-05-050150
Pump Priming and Air Bleed Valve
An air bleed valve is included with each pump to aid in system priming. It is shipped in the pump accessories
bag and must be installed during system installation. Why use an air bleed valve:
Your system is equipped with a 4 lb. check valve
on each metering tube. These valves do not let air
escape from the system unless it is pressurized.
12 volt liquid pumps are not good air compressors.
Therefore, the pump can struggle to prime due to
air trapped on the outlet side of the pump.
The air bleed valve is a small 1/4” valve that when
opened lets air escape from the pump outlet at
zero pressure. Open until liquid comes out and
then close the valve.
How to install the air bleed valve:
Remove the 1/4” plug from the quick connect fitting
on the center cross on the Tower (see picture).
Next, insert the 1/4” tubing in the quick connect
fitting. Run the 1/4” tubing to an easily accessible
spot on your equipment. Next, cut the tubing and
push the 1/4” valve onto the tubing. Finally, run the
tubing to a low location where any fertilizer that
escapes will run on the ground.
Be sure the air bleed valve tube does not
become plugged with dirt or it will not allow air
to bleed.
1/4” Tubing 1/4” air bleed valve
Shipped
from factory
with plug
installed.
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 8 Revised 04/13/2016
B
Components
Liquid
Floating Ball Flow Indicator & Manifold System
Flow indicators give a clear visual signal that a
fertilizer system is working. These indicators use an o-
ring and wire clip connection to snap together in any
configuration necessary.
The flow for each row will pass through a flow indicator
that has one or two balls that will float to indicate flow to
that row. This will give an immediate visual indication of
flow to each row. While the flow indicators give a good
indication of the flow to each row, they are not always
an indicator of the exact flow to each row. Only a catch
test will verify the evenness of the row-to-row
distribution.
For most applications of NutriSphere-N NH3 at 32 oz/
acre, the Green Plastic ball gives a good flow
indication. If a heavier ball is needed, use the Red ball.
On this low-flow system, the flow appears to be more
stable if only one ball is used.
Parts List
Complete Columns
701-20460-920-
GR-VSingle Low Flow Column with 1/4" QC - 90 Degree Outlet
Fittings
Service Parts Only
701-20470-00 Low Flow Column
701-20460-04 Wilger Lock U-clip
701-20516-00 ORS x 1/4" QC - 90 Degree 701-20460-05 Flow Indicator Ball - 1/2" SS Ball
701-20460-06 Flow Indicator Ball - Maroon Glass
701-20460-07 Flow Indicator Ball - Red Celcon
701-20460-08 Flow Indicator Ball - Green Poly
701-20460-09 Flow Indicator Ball - Black Poly
701-20521-00 Wilger End Cap 701-20460-15 Viton O-Ring for column & fittings
701-20523-00 ORS Male x ORS Female x 3/8" FPT - Isolator 701-40225-05 Viton O-Ring for Orifice
701-20525-00 ORS Male x ORS Male x 1" FPT - Tee
Brackets & U-Bolts
400-1037A1 3-6 Row Bracket
400-1036A2 7-12 Row Bracket
400-2011A1 White Backer Plate for 3-6 Row Bracket
400-2010A1 White Backer Plate for 7-12 Row Bracket
400-1315A2 Flow Indicator Bracket, 6-8 in wide hitch mount
Product Distribution
To assure proper and even distribution to each row, the product being applied
must be metered to each individual row. This metering is done by using
metering tubes which create back pressure so an equal amount of liquid is
applied to each row.
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 9 Revised 04/13/2016
B
Components
Liquid
400-1037A1
3-6 Row
Bracket
400-2011A1
6 Row White Visi-
bility Backer Plate
The low flow column has a smaller internal
diameter. This means a heavier ball can be used to
monitor a smaller flow.
Externally, the low flow column can only be
identified by “Low Flow” molded into one side of the
column. All the same fittings work with low flow and full
flow columns.
Floating Balls
For most applications of NutriSphere-N NH3 at 32 oz/
acre, the Green Plastic ball gives a good flow
indication. If a heavier ball is needed, use the Red ball.
On this low-flow system, the flow appears to be more
stable if only one ball is used.
Low Flow Column (mostly 1/4” QC)
Ball retainer—If top is
removed, be sure that
the ball retainer is in
place when top is
reinstalled.
Flow Indicators and Dual Check Valves
Assembly of top of flow indicator tube
Some systems may have a dual check valve
system with two metering tubes as shown at the
right. On this system, flow can be directed to the
small tube, or to the large tube, or to both tubes
by opening or closing the valves by twisting the
blue caps.
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 10 Revised 04/13/2016
Dual Metering Tube Plumbing Kits with
Dual Check Valve
The SureFire Catalyst Tower 100 NutriSphere-N NH3 system comes with a dual metering tube distribution
system. These plumbing kits will contain everything you need to distribute product from the flowmeter outlet
down to the ground application device.
For most applications of NutriSphere-N NH3 at 32 oz/acre on 30” rows, the purple tube will be the tube that is
used. When applying in cold weather and/or at high speeds, it may be necessary to use the blue tube. The
system will work at pressures up to 50 PSI, but for prolonged use above 45 PSI, consider switching to a
larger tube.
Dual Advantage of Dual Metering Tube
Metering tube provides a larger passage way diameter than a comparable orifice. Typical NutriSphere-N
NH3 applications apply around 1 to 1.5 oz/min/row. An orifice for this rate would have a 0.015” diameter
opening. The SureFire system uses metering tubes with diameters of 0.080” (purple) and 0.096” (blue). This
12’ tube with more than three times the diameter creates a fertilizer system resistant to plugging while
providing excellent row to row distribution.
By using two metering tubes, the fertilizer system can provide the proper system pressure as the fertilizer
properties change due to temperature, mixtures and other factors.
Standard Orifice Metering Tube
2x
Field Operation of Dual Metering Tube
B
Components
Liquid
Not actual size
Note: Flow tests with water will have very different pressure readings than what the system will have with
NutriSphere-N. The pressure will be much less with water for a given flow than with NutriSphere-N.
The best tube to use may change, based on temperature, application speed, and product batch,
SureFire recommends you start with the Purple tube (for typical 32 oz/ac and 30” row spacing).
Conduct a test using the Liq Cal procedure to determine your system pressure. Recommended pressure is
between 10-40 PSI.
The system will operate up to 50 PSI. If prolonged application with pressures above 45 PSI is anticipated,
consider changing to the blue tube.
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 11 Revised 04/13/2016
B
Components
Liquid
Typical plumbing setup
Your shanks and plumbing setup may vary from those shown here.
The 4’ green tube delivers the product to the shank.
1. Slide a 2’ piece of 3/8” hose over the green tube along with 2 clamps.
2. Slide the green hose in the tube on the shank as far as it will go.
3. Slide the 3/8” hose down over the tube. Clamp 3/8” hose at the top and at the bottom.
4. Connect purple tube to green tube with 1/4” QC x 1/4” QC. Cap both ends of the blue tube. Blue tube will be used
when cold weather and/or high speeds create too high pressure in purple tube.
5. Connect purple tube to appropriate length of black tube with 1/3 lb 1/4” QC check valve. Connect this black tube to
top of flow indicator.
123
45
For 32 oz/ac rate and
speeds 7 mph or less,
the green ball will work
best. Higher speeds
may work better with
the red ball.
1/3 lb check valve
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 12 Revised 04/13/2016
Shanks and Knife Points available from SureFire Ag Systems
SureFire Ag Systems and Verdesian have worked closely with an established shank manufacturer to develop
a shank and several knife points that will deliver the anhydrous ammonia and NutriSphere-N NH3 where it
needs to go. They will be able to advise users on the best setup for their application scenario.
The knife on the left is for no-
till conditions. On the right is
a less aggressive point for
tilled soil.
Anhydrous tube
NutriSphere tube
Insert a piece of black 1/4”
tube inside the NutriSphere
tube and push it down so
the end of the black tube is
at the top of the outlet hole.
(See instructions on
previous page.)
To protect the black 1/4”
tube, slide a 2-foot long
piece of 3/8” hose over the
black tube and clamp this
hose to the top of the
NutriSphere tube.
Your application setup may be
different. Generally, insert the
black 1/4” tube into the tube
through which the NutriSphere-N
NH3 will be applied.
On NutriSphere placement tubes
that are open on the bottom, a
slightly higher velocity stream
may be achieved by using a 30-
36” piece of purple tube as the
final discharge tube. Insert this
purple tube inside the
NutriSphere placement tube and
push it to the bottom of the tube.
If the purple tube is used, the
length of this tube should be the
same on all rows.
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 13 Revised 04/13/2016
Toolbox (no tools, just spare parts)
A toolbox containing critical items will be included with each system. The toolbox will
contain:
QTY
 1 12 volt electric pump
 2 flow indicator columns
 10 size 6 hose clamps
 1 3/8” HB 90 degree electric pump fitting
 1 3/8” HB straight electric pump fitting
 2 40 Amp fuses
 11” Tee Strainer gasket-FKM
 2Clips for electric pump
 4QC 1/4” End Stop White Poly Cap
 6QC to QC—1/4” QC x 1/4” QC
 2Check Valve—1/3 lb—1/4” QC x 1/4” QC
B
Components
Liquid
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 14 Revised 04/13/2016
D
Wiring & Elec
Pro 700 AccuControl Field-IQ™
Rate and Section Control Module
The SureFire system begins at the Field-IQ Rate and Section Control Module. The picture
below shows this control module. You will need to purchase this module from your Case IH
dealer. You will also need to purchase an unlock code for your Pro 700 display to enable rate
control functions.
The rate controller has two harness connections. The first is the connection to the Case IH
wiring harness that connects to the in-cab display. The second is where the SureFire
harnesses begin. The following pages show system diagrams for single section and 2-section
configurations. Detailed harness drawings follow for information and troubleshooting.
Instructions for setting up the AccuControl on the in cab display are in Section F. Detailed
screen shots of the Pro 700 display are included showing exactly what settings are required
and recommended for the SureFire system.
Check with your dealer at least annually to be sure that the Pro 700 display and the Field-IQ
module have the latest software/firmware updates.
18-Pin Connector-
Connect to Case IH
Harness back to in-cab
display
Field-IQ Rate and Section
Control Module
30-Pin Connector-
Connect to SureFire
Harness
SureFire Harness
201-215464Y3
2-pin Power
Connector
(P5)
-Connect to
SureFire
Harness
Aux Master/Dump Valve (12-
pin Deutsch connector) on 201-
215464Y2 plugs into Aux I/O
(12-pin Deutsch connector) that
comes from 18-pin connector
harness. (Only needed if using
Aux Master/Dump Valve.)
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 15 Revised 04/13/2016
D
Wiring & Elec
Case IH AFS AccuControl
Rate and Section Control Module
This chart shows you the output functions by pin location on the AccuControl Rate and
Section Control Module. Use this information to verify if the AccuControl system is providing
the correct output. If the module is not providing the correct output, contact your Case IH
dealer to repair the problem. Also review any applicable settings on the display to verify the
system is properly set up.
AccuControl Rate and
Section Control Module
30 Pin Connector
30-Pin Connector-
Connect to SureFire
Harness 201-215464Y3
18-Pin Connector-
Connect to Case IH Harness
back to in-cab display
Common Troubleshooting:
PWM Signal to Pump: Pins E1 to E2 should have 0-12 volts to energize the EPD
module to run the pump. Use manual mode to increase signal. Should get up to 12
volts after holding increase button.
Flowmeter Tap Test: Pins C2 and C3 are Flow Ground and Signal. If no flow is
registering on the display, you can tap between these two pins with a short wire. This
produces a pulse. The display should indicate a flow when this is done rapidly. (Note:
To help register flow for the tap test, change the flowmeter calibration to 10, so it will
show a flow with fewer taps. Be sure to reset the flow cal to the proper number after
the test.)
See the drawing of harness 201-215464Y3 on page 18 for all pin locations on the
30-pin connector.
Note: If applying 2 products (such as anhydrous ammonia and NutriSphere-N
NH3) with the Pro 700 AccuControl you will need 2 Field-IQ Modules.
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 16 Revised 04/13/2016
Tower & Pro 700 AccuControl Layout
Control: PWM EPD
Sections: 2
P/N 207-
215223Y2
P/N 201-215464Y3
30-Pin to twin 16-Pin
Adapter Harness
If the implement is set up as two sections, you will use
the connector for Section 1 on the left side and Section 2
on the right side. (Implements less than 60’ wide will be
configured as 1 section.)
Can use 3-Pin Weatherpack Extension cables to reach
section valves if needed.
If implement is set up with just one section, you will use
the Section 1 connector to connect to the Flow Indicator
Manifold Shutoff valves. A 4’ Y Adapter Cable (201-
215604) will be connected to the Section 1 connector on
207-3057Y1. One Y connector will supply the valves on
the left side. The other Y will supply the valves on the
right side.
PWM Flow
Pressure
(not used
on Pro 700)
Field IQ
module
Pro 700
display in
cab
Case/Trimble
harnesses
D
Wiring & Elec.
Pressure
P/N 207-215466
for 1 or 2 Sections
1 2 4 5 6
Implement Lift Switch
Connector (optional)
2-pin power connector
SureFire Ag Systems

396-3053Y1 SureFire Tower 100 for NutriSphere®-N NH3 for Pro 700 17 Revised 04/13/2016
40 Amp PWM EPD
(Pulse Width Modulated Electric Pump Driver)
Item Number: 205-19024 with Anderson connectors
Replaces 205-18385 with 480 connectors
D
Wiring & Elec.
40 Amp in-line fuse
EPD Power Harness
PN 205-3118Y1 (20 feet) -
connect to tractor battery
Plug in pump directly to
power harness from
battery when trouble-
shooting issues.
Use EPD Power Harness Extensions as needed
(These have Anderson Connedtors) Wire Size
206-02-3120Y1 1’ Extension 10 gauge
206-02-3121Y1 5’ Extension 10 gauge
206-02-3122Y1 10’ Extension 8 gauge
206-02-3123Y1 20’ Extension 8 gauge
206-02-3124Y1 30’ Extension 30’ and longer—6 gauge
206-02-3125Y1 40’ Extension
206-02-3126Y1 50’ Extension
206-02-3127Y1 60’ Extension
206-02-3128Y1 2’ Anderson Ext w/ Power Switch-8 AWG
SureFire recommends a single long extension harness as multiple
connectors will reduce voltage, increase current and hurt
performance of your electric pump system.
Troubleshooting Tip:
If the pump won’t run, connect the
power and pump connector directly
together to give pump full 12 volts
directly from battery. This will tell
you if the pump is the problem or if
something else is wrong. The pump
will be running at full speed, so don’t
leave it connected this way for long.
The Electric Pump Driver powers the electric pump by providing a pulse width modulated signal to control
pump speed. It needs to have a power connection and wiring capable of carrying up to 40 amps of current.
It must be connected directly to the tractor battery. SureFire recommends 10 gauge (or heavier) wire
if extending harnesses in the field.
PWM Connection
on harness 207-
3057Y1
SureFire Ag Systems

Project:
Filename:
201-215464Y4 Trimble Field IQ Adapter Cable –30 pin to twin
16 pin—2 pressure, 10 section, aux/dump valve
Trimble Field IQ Adapter Cable –30 pin to twin 16 pin
Drawn By:
Date:
Brady Gragg
Rev. by Mark Wolters, Ricker
10/23/12
Rev. 09/27/2013, 8/25/2014,3/3/2016
Page of Pages 1 of 1Copyright 2012-2016 SureFire Ag Systems
201-215464Y4
Trimble Field IQ Adapter Cable –30 pin to twin 16 pins- 2 pressure
Wire Size: 18 AWG unless
otherwise specified Length: 3ft
1GND
16 Pin Round –AMP
Female pins in female body
(with swivel nut)
Prp
Grn
2
3Servo +/ PWM
Yel
4
5
6
7
8
9
10
11
12
13
14
15
16
Blk
Blu
Red
A1
Section 2
Section 3
Cinch Connector
Wht/Blu
Blu
B1
C1
Section 4
Brn
D1
E1
F1
G1
H1
J1
K1
A2
B2
C2
Pressure 1 Signal Prp
D2
E2
Impl Switch 5V
F2
G2
H2
J2
K2
A3
B3
C3
D3
Impl Switch Signal
E3
Servo +/PWM
Blk
Blu
F3
G3
Flow Signal
Yellow
H3
J3
K3
Green
1Valve GND
Section 2
16 Pin Round –AMP
Male pins in male
body
(with threads for
swivel nut)
2
3Section 3
4
5
6
7
8
9
10
11
12
13
14
15
16
Blk
Labeled
“Sections”
Labeled “To Pump”
2
+12VDC
GND
2 Pin Connector –
Deutsch DTP04-2P Male
(Power In)
14 AWG Blk
1
14 AWG Red
Red
Red
Red
Red
Section 4
Section 5
Section 6
Section 7
Section 8
Section 9
Section 10
Pressure 2 Signal
Aux/Dump Valve
Pressure 1 Signal
Valve Power
Section 1
Valve Power
Section 5
Section 6
Section 7
Section 8
Section 9
Section 10
Section 11
Section 12
Section 1 Blk
Blk/Wht
Brn/Wht
Wht/Blk
Wht/Brn
Pnk
Blu/Wht
Wht/Blu
Blu
Brn
Prp/Wht
Pink
Blk/Wht
Brn/Wht
Wht/Blk
Wht/Brn
Pnk
Blu/Wht
Blk
Prp
Servo -/ PWM
Blk
Section 1
Blk
Pressure 1 Signal
Flow GND
Flow Signal
Power
Flow GND
Servo -/PWM
Red
Red
150 MP
TOWER
3-PIN
A
B
C
Mates with
215466 or
215467
Mates with
215223 or
215218
Pump
Dust Cap
Sections
A
Imp Sw Signal
150 MP
SHROUD
3-PIN
B
C
Run/Hold
Plug
Plug
Plug
Attach Dust
cover to
Connector
Pressure 2 Signal
+12V
GND
+12V
GND
Imp Sw 5V
GND
POWER
+ 5V
Prp/Wht
Prp/Wht Pressure 2 Signal
12 Pin Connector
Deutsch DTM04-12P
Pink
Pink
PIN 1
Aux/Dump Valve Signal
Master On/Off
Section 2
Brn
SureFire Ag Systems
18