Surewood Cabinetry NS-WDC2430-F User manual

Surewood Cabinets
Compass Manufacturing International / Louisville, KY / www.cmiproduct.com
Wall Diagonal Corner Cabinet (WDC)- Assembly Instructions
(Includes 30”, 36”, 42” High)
Parts with Universal Box
2 Side Panels, 1 Left and 1 Right
2 Back panels 1 Left and 1 Right
1 Bottom Panel
1 Top Panel
1 Diagonal Back Panel
2-3 Shelves (depending on the height of the cabinet)
1 Package of Screws & Brackets
Parts with Face Frame and Door
1 Face Frame with Door attached.
1. Identify all parts.
2. You should have 2 (qty) boxes for your wall cabinet; one containing the Face Frame with Door/s attached and one
containing the cabinet body parts.
3. Make sure to have clean clear area to work with so the cabinet does not get scratched (carpet, foam, rubber mat). Lay
Face Frame of Cabinet face down on soft smooth protected surface (Diagram A).
4. Slide left side panel into left slot on face frame making sure the pre-cut slots & shelf holes in the panel are facing
towards the inside of the cabinet (Diagram B). TIP: Pre-fit the side panels into the Face Frame and if they seem too
tight lightly sand the edge of the dovetail. TIP: Placing a thin bead of wood glue in the grooves before sliding the panels
in will help with the sturdiness of the cabinets. If the panel is a little too tight to slide freely, use a rubber mallet to
gently tap into place.
5. Repeat step 5 with the right side panel.
6. Slide top panel into pre-cut slots provided in the side panels (Diagram C).
7. Repeat Step 7 with bottom panel.
8. Slide the left and right back of cabinet into groove provided on side panels and the top and bottom into the groove in
the back panels (Diagram D). TIP: A small bead of glue in the grooves (dado) will help strengthen the cabinet .
Tools Required Tools Optional
Philips Screwdriver Power Drill/Screw driver
Wood/Rubber Mallet Power Pin gun w/ 5/8” pins
Hard Wood Block Square
Utility Knife
Fine Sandpaper 240 grit
Tape Measure
Small wood chips or toothpicks
Diagram A
Diagram C
Diagram B
Diagram D

9. Use ¾” screws to fasten back panels to the Top & Bottom. There are 4 screws for each back panel. We suggest you put
these in using a screwdriver instead of a screw gun unless you have one with a low torque setting (Diagram D). MAKE
SURE SCREW HEADS ARE PAST THE SURFACE OF THE SIDE PANEL. TIP: If you should strip the screw just back it out and
put in a wood chip or a couple of tooth picks and put the screw back in. BE CAREFUL!
10. Use ¾”screws to place the 45 degree wood corner blocks on the back of the Face Fame. Do this on both top and bottom
of the cabinet (Diagram E).
11. Use ¾”screws to place the 90 degree Metal corner blocks in both of the corners where the side panels meet the back
panels. Do this on both top and bottom of the cabinet (Diagram F).
12. Place the Diagonal Back Panel at the back of the cabinet and line up the grooves with the top and bottom panels
(Diagram G).
13. Use screws provided to place the 45 degree Metal corner blocks where the diagonal back meets the left and right back
panels. Do this on both top and bottom of the cabinet (Diagram H).
14. Stand cabinet up and open door facing you.
15. Place shelf clips in predrilled holes provided and adjust to desired shelf height (Diagram I).
Diagram E
Diagram F
Diagram I
Diagram D
Diagram G
Diagram H

16. Place shelves inside on the bottom the cabinet.
17. Move shelf from bottom of cabinet at an angle and place on the shelf clips.
18. Repeat steps 13 and 14 for the remainder of shelves. (If applicable).
If you have any questions please contact the dealer you purchased the cabinets from or contact us through our
web site at www.cmiproduct.com