Surveillance 112 Pz0312 User manual

Catalogue

Production-------------------------------------------------------------------------------------------------------------------------------------3

Note / Warning / Friendly suggestion

Installation and connection--------------------------------------------------------------------------------------------------------------4

Indoor & Outdoor IR High Speed Dome Camera----------------------------------------------------------------------------------5

1. Features

2. Mounting size drawing

2.1 Wall mount

2.2 Hoisting mount----------------------------------------------------------------------------------------------------------------------------6

3. Hardware setting

3.1 Dial codes switch setting

3.2 Baud rate setting

3.3 Address codes setting

4. OSD menu setting------------------------------------------------------------------------------------------------------------------------7

4.1 Menu setting operating introductions

4.2 Basic introduction

4.2.1 Select item

4.2.2 Parameters setting operation

4.3 System setting of the dome camera

4.3.1 Info display setting-----------------------------------------------------------------------------------------------------------------8

4.3.2 System act setting

4.4 Camera setup------------------------------------------------------------------------------------------------------------------------------9

4.5 PAN setup-------------------------------------------------------------------------------------------------------------------------------- 10

4.5.1 Scan setup / Pattern scan setting / Tour scan setting / Auto scan setting

4.5.2 Auto flip function------------------------------------------------------------------------------------------------------------------11

4.5.3 Home (Fixed) position

4.6 Calendar setup

4.7 Call the shortcut of preset positions (Pelco-D/P protocol)--------------------------------------------------------------------12

Indoor & Outdoor Normal High Speed Dome Camera (W/O IR) ------------------------------------------------------------13

1. Features

2. Mounting size drawing

2.1 Wall mount

2.2 hoisting mount

3. hardware setting ------------------------------------------------------------------------------------------------------------------------14

3.1 Dial codes switch setting

3.2 Baud rate setting

3.3 Address codes setting

4. OSD menu setting

4.1 menu setting operating introductions

4.2 Basic introduction ----------------------------------------------------------------------------------------------------------------------15

4.2.1 Select item

4.2.2 Parameters setting operation

4.3 System setting of the dome camera

4.3.1 Info display setting

4.3.2 System act setting---------------------------------------------------------------------------------------------------------------16

4.4 Camera setup

4.5 PAN setup -------------------------------------------------------------------------------------------------------------------------------18

4.5.1 Scan setup

4.5.2 Auto flip function-----------------------------------------------------------------------------------------------------------------19

4.5.3 Home (Fixed) position

4.6 Calendar setup

4.7 Call the shortcut of preset positions (Pelco-D/P protocol)-------------------------------------------------------------------20

Clean the dome cover

Notes for maintain / Lightning protection / Simple sheet for check faults---------------------------------------------21

SONY zoom module menu for reference ------------------------------------------------------------------------------------------23

LG zoom module menu for reference-----------------------------------------------------------------------------------------------24

CNB zoom module menu for reference---------------------------------------------------------------------------------------------25

SAMSUNG zoom module menu for reference

Products introduction

Thank you for using our INTELLIGENT SPEED DOME CAMERA

Our products use perfect function design of high performance digital DSP, stable performance. The key parts, we use

world famous bands, like electrical motor, zoom module, electrical ring, IR lights components. With the perfect electrical

circuit design and convenient installation method, make it can tracing objectives fast and correctly. It can monitor all

locations in 24 hours. The skillful design of hardware reducing failure rate as its possible. The human design of software

make the operation become simple and convenient. These advantages make the system become convenient for

installation, using, maintaining, and working stably. We believe our products have excellent performance, so it can be

the best in the industry! These products can be applicable to intelligent building, bank security protection, city roads,

airport, quay, station, residential district, industrial factory and mine and so on. It can meet various demands, in

anywhere, and various moving targets.

Notes

A. Please read the installation instructions before you operate it;

B. Please comply with safe operating instructions when you operate it;

C. Only professional and experienced worker can operate the installation and maintain works of it;

D. Please use reliable tools, those tools which of poor quality maybe causing dangerous situation;

E. Please ensure the installation and using environment is in line with our products demands;

F. Please check the space for install the supporter, including strength and toughness, the weight support capacity of

substrate at least up to 5 multiples of both products and parts;

G. Please save the packaging of product, in order to package and transport it in the future.

Warning

A. Don't put it near to inflammable and explosive things, please keep it far away dangerous areas;

B. Don't put it on the unstable or supporter;

C. Don't let any foreign material and liquid into the machine, that will damage it;

D. Don't try to use wrong power or adaptor to supply electricity, it's power voltage is DC 12V;

E. Please recognize the RS-485 control wire;

F. Don't try to supply power for it before you have not finish the installation;

G. Don't try to take it apart to repair;

H. Don't use corrosive cleaner to clean it;

I. Please don't let the camera face to strong light directly, like strong lamp light, strong sunlight, etc. Otherwise its

CCD maybe damaged forever;

J. Please do not let it bear weight pressure or strong hit, and strong shake;

K. Please read the introductions carefully before you operate it.

Friendly suggestions

1. Please use high quality and safe power supply, our standard power adaptor should be near to the camera, the best

distance is within 3m, to avoid too much attenuation, please make sure your power supply is enough.

2. We suggest you to use high quality wires for both power and transmission, and avoid to tie a knot wires, please try

your best to wiring smoothly, sometimes you have to connect many wires together, please be careful to make the

connection point be perfect, don't think one core is not important, don't just tie them together, please make all cores

one-to-one. Please consider to add electronic resistance and UPS when you find the power supply is not normal.

3. Please never carry the wire which is outside the dome, and don't let that wire to bear the camera weight.

4. We suggest you’d better to do some grounding and lightning protection measures, because speed dome camera

have control cable, it is easier to be hit by thunder and lightning than other normal camera.

Installation and connection

Notes before installation

1．Installation must by the professional technicians or someone which have qualification.

2．Detailed wiring method please reference the installation sketch map and the install introductions.

3．When you installing camera, please use clean gloves, and avoid to use metal/strong objects/hands to touch the

dome or its cover, in order to avoid damage the cover and affect image quality.

4．After you finish the installation, please use soft and clean cloth or towel to clean the transparent cover carefully,

unclean fingers will make smudges on the cover, then will affect the image to be unclear.

Installation requirements

zPlease check the accessories are complete before installation;

zBefore installation, please make sure the camera's using place and installation method are meet the requirement of

the machine.

zInstallation must operated by professional worker, and should comply with related rules, in order to avoid faults.

zYou must to use right installation tools, like screwdriver etc, please check the dial code switch is right or not.

Installation method

The installation place or wall must be strong and no constructing problems, the weight support capacity of installing

place at least up to 4 multiples of both products and parts, including the supporter, in order to avoid camera fall down

due to it's unstable.

Installation steps

a. Take out the supporter from box, draw a central position of the drilling hole on the wall;

b. Use M8 electrical hammer to dill 4 holes on the position that out of the central position, then fix M6 screws in it;

c. Insert the wires from supporter top into the supporter inside, leave enough length for the connecting wire;

d. Put 4 holes of the supporter on those 4 screws, fix gaskets, screw those 4 screws, then fix the supporter and

camera on the wall;

e. Clean the cover after installation.

External wiring connection

zPut the BNC video interface connecting to the fixed video wire;

zPut the power wire connecting to the fixed power wire (DC12V/5A);

zPut the RS 485 control wire connecting to the fixed control RS 485wire,.please check the positive and negative of

RS 485wire, make its in accordance with the remarking connection method on the wire head, if you make its

converse, it can't get communication. A is positive of RS485 wire ( generally be orange ), B is negative of RS485

wire ( generally be yellow ).

zPlease check the whole routes after you connect every wires, including: The polarity and connecting method of

power and control wires. If you are sure they all are right, you can turn on the power. The camera will checking

itself after turn on power. It will rotating 360° in horizontal firstly, then rotating 90° in vertical. At the same time,

every checking informations will display on the screen, like the address, communicating speed rate, camera. After

finish all checking, it will stop, this means it's finished checking and waiting for your controlling.

Indoor & Outdoor IR High Speed Dome Camera

1. Features

z128 accurate preset positions, 2 pattern scan routes, 4 tour routes, 1 fixed monitoring position

zDisplay PTZ direction and zoom number, and temperature

zEnglish OSD menu for operation.

zRS-485 communication, auto identify protocol of Pelco D / Pelco P

zAddress codes range: 1~255

zBaud rate: 2400/4800/9600/19200, set by dial codes

zHorizontal rotating range: 0° –360° continuously

zHorizontal rotating speed: 0° –220° /sec

zVertical rotating speed: 0° ~100° /sec, auto flip

zWorking temperature: -20° C--+75° C

zWorking humidity: less than 95%

zWaterproof cover level: IP65

zBuilt-in constant temperature control system

zInstallation methods: Hoisting installation, wall mounted installation

zPower: DC12V/ 5A power supply.

2. Mounting size drawing

2.1 Wall mount

2.2 Hoisting mount

3. hardware setting

3.1 Dial codes switch setting

Open the codes cover on top of dome cover, see the dial codes of 10 numbers, you can turn every number ON or OFF

3.2 Baud rate setting

High speed dome camera can auto identify the Pelco-D / Pelco-P, then starting work, so you just need to set baud rate

and address codes of the camera, it can starting normal working. Baud rate can set through the 9th ~10th dial codes,

setting method as below: factory default as 2400bps.

Baud rate and dial codes switch matching sheet

Dial codes 2400 bps 4800 bps 9600 bps 19200 bps

No. 9 OFF ON OFF ON

No. 10 OFF OFF ON ON

3.3 Address codes setting

10numbers dial codes switch, (picture 01) No.1~ No.8 are use to set the address codes, you can set address codes

within the range 1~256, factory default as 1. Use binary, dial every number to be "ON" is means as 1, dial to be "OFF"

is means as 0, details please reference the sheet.

Address codes and dial codes switch sheet (Binary), calculate it according to this sheet

Binary Add Binary Add Binary Add Binary Add

0000000 0 11110000 15 01111000 30 10110100 45

10000000 1 00001000 16 11111000 31 01110100 46

01000000 2 10001000 17 00000100 32 11110100 47

11000000 3 01001000 18 10000100 33 00001100 48

00100000 4 11001000 19 01000100 34 10001100 49

10100000 5 00101000 20 11000100 35 01001100 50

01100000 6 10101000 21 00100100 36 11001100 51

11100000 7 01101000 22 10100100 37 00101100 52

00010000 8 11101000 23 01100100 38 10101100 53

10010000 9 00011000 24 11100100 39 01101100 54

01010000 10 10011000 25 00010100 40 11101100 55

11010000 11 01011000 26 10010100 41 00011100 56

00110000 12 11011000 27 01010100 42 10011100 57

10110000 13 00111000 28 11010100 43 01011100 58

01110000 14 10111000 29 00110100 44 11011100 59

If you use other equipments to control the camera, because of the protocol limitation, some special function maybe

cannot use. When you use other equipments to control the camera, you need to set the protocol (auto identify), baud

rate, address codes to be right. Different factories have different address codes, so sometimes you need to add 1 or cut

1 when you setting address codes. For example, you set the address code of camera to be 2, then you need to set

DVR controlling address code to be 3 or 1, then you can control it.

Remarks: alarming output switch always opening, K1~K8 are use to connect outside input signal

4. OSD menu setting

4.1 menu setting operating introductions

When the camera power on, its basic informations will display, like protocol, baud rate, address code. After finish the

checking and accept your controlling, these informations will disappear. ( user can see all setting info at here ) OSD

menu setting method:

Enter the main OSD menu: call #59 / #95 preset position to enter the main menu, then can set every item.

Use the keyboard: call 59 / 95 number keys (call preset position) to enter main menu, then shake the joystick to shift up

/ down / left / right ( ←↑→↓ ), every keys functions as below:

menu setting functional keys

No. Original functions of the keyboard Functions after enter the OSD menu

1 joystick: up Menu cursor: up

2 joystick: down Menu cursor: down

3 joystick: left Menu cursor: left

4 joystick: right Menu cursor: right

5 Iris close/ Iris (Iris - ) Menu: back

6 Iris open/ Iris (Iris + ) Menu: enter

4.2 Basic introduction

4.2.1 Select item

Use the keyboard: call 59# / 95 # preset position to enter main menu, then see a sheet as below:

Use the joystick up / down to select item, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to

confirm select this item, or enter the next sub menu:

Change the language to be English: move the joystick down to the bottom, press the key "Iris+" (or the key "OPEN"

on the keyboard ) to confirm select the item of "LANGUAGE", shake the joystick to change language to be "ENGLISH".

SYSTEM SETUP

CAMERA SETUP

PAN SETUP

CALENDAR

LANGUAGE ENGLISH

4.2.2 Parameters setting operation

Shake the joystick up / down to change number of every item, press the key "Iris+" (or the key "OPEN" / "ENTER" on

the keyboard ) to confirm select this item and save this setting.

Press the key "Iris-" (or key "CLOSE" / "RETURN" on the keyboard ) to exit this menu, or back to the previous menu.

4.3 System setting of the dome camera

Shake the joystick up / down to make the cursor be under the "SYSTEM SETUP" item, then press the key "Iris+" (or the

key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, or enter the next sub menu: as the sheet:

INFO DISPLAY

SYSTEM ACT

SET DOME TITLE

4.3.1 Info display setting

Shake the joystick up / down to make the cursor be under the "INFO DISPLAY" item, then press the key "Iris+" (or the

key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, or enter the next sub menu: as the sheet:

TITLEINFO OFF

COORDINATE OFF

TEMPERATURE OFF

Shake the joystick up / down to select, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to

confirm select this item.

CAMERA

TITLE ON/OFF

COORDINATE ON / OFF

TEMPERATURE ON / OFF

ZOOM OFF

Press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, then shake the

joystick up / down, you can select "DISPLAY" or "OFF". Finish the setting select, press the key "Iris+" (or the key

"OPEN" / "ENTER" on the keyboard ) to confirm and save your set value. You can press the key "Iris-" (or the key

"CLOSE" / "RETURN" on the keyboard ) to exit this menu , and back to the previous menu.

4.3.2 System act setting

Shake the joystick up / down to make the cursor be under the "SYSTEM ACT" item, then press the key "Iris+" (or the

key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, or enter the next sub menu: (as the sheet:)

POWER UP ACT NOTHING

LEISURE ACT NOTHING

LEISURE TIME 003~240 (SECONDS)

RESET

Power up act: means after camera power on and finish checking, the action that users want it to do, the factory default

is "nothing (no any action)":

Shake the joystick up / down to make the cursor under the "POWER UP ACT" item, press the key "Iris+" (or the key

"OPEN" / "ENTER" on the keyboard ) to confirm select this item, then shake joystick up / down to select what action you

want, there are 10 options can be selected: nothing / pattern scan route / cruise route scan / limiting position scan/ auto

scan/ fixed position scan (home). Select one, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard )

to confirm and save your set value. You can press the key "Iris-" (or the key "CLOSE" / "RETURN" on the keyboard ) to

exit this menu, and back to the previous menu.

Leisure act: means the camera haven't any actions after a period of time which you set, if you don't control it beyond

this time, it will auto working a action you set before. The factory default is "nothing":

Shake the joystick up / down to make the cursor be under the "LEISURE ACT" item, then press the key "Iris+" (or the

key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, then shake joystick up / down to select what action

you want, there are 10options can be selected: nothing / pattern scan route / cruise route scan / limiting position scan /

auto scan / fixed position scan. Select one, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard )

to confirm and save your set value. You can press the key "Iris-" (or the key "CLOSE" / "RETURN" on the keyboard ) to

exit this menu , and back to the previous menu.

Leisure time: (factory default is "30 seconds")

Shake the joystick up / down to make the cursor be under the "LEISURE TIME" item, then press the key "Iris+" (or the

key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, then shake joystick up / down to select time

(3~240 seconds). Finish the setting select, press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to

confirm and save your set value. You can press the key "Iris-" (or the key "CLOSE" / "RETURN" on the keyboard ) to

exit this menu, and back to the previous menu.

Reset:

Shake the joystick up / down to make the cursor be under the "SYSTEM RESET" item, then press the key "Iris+" (or the

key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, then screen appears "?", you need to enter the

camera secret codes, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm, 2 seconds

later, the camera will restore to factory defaults.

Set camera title:

Shake the joystick up / down to make the cursor be under the "SET DOME TITLE" item, then press the key "Iris+" (or

the key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, then screen appears "?", shake the joystick up

/ down to select the letters (a~z, A~Z) and numbers (0~9) you want, move the joystick left or right will move the cursor

location, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm.

4.4 Camera setup

Shake the joystick up / down to make the cursor be under the "camera setup" item, different camera have different

parameters for selection, different modules have different menu. Our standard module menu generally as below:

After enter the main menu, you can choose these menu items as below by the key "zoom" (the key "zoom" original

function is for change the image zoom definition ), or use the joystick, use "focus" to change value.

F RANGE: 5M /3M /1M--------the range of the FOCUS

CAMERA ID: 000:--------000-255(selectable by useing the key "zoom")

ID DISPLAY: ON/OFF:--------"ON" means display, "OFF" means no display(selectable by useing the key "zoom")

FOCUS: MANUAL/AUTO: --------manual zoom (defaults)/ auto zoom(selectable by useing the key "zoom")

ZOOM START: 01:--------default is 01X,(selectable by useing the key "zoom")

ZOOM END: 23:--------default is 23X,(selectable by useing the key "zoom")

BLC: ON/OFF:--------back light compensation is selectable,ON/OFF(selectable by useing the key "zoom")

RESET:--------restore factory settings

EXIT:--------return

ID: --------ID of every camera, in order to control all cameras more conveniently, from 1~255

FOCUS:

FOCUS MODE----AUTO: real time, default; MANU: manual focus; PUSH: find image clear point when the zoom

stopping, then focus, will not focus again. (MANUAL MODE, if change zoom, focus mode will auto change to AUTO

FOCUS MODE; AUTO MODE, if change zoom, focus mode will auto change to MANUAL FOCUS MODE)

FOCUS DISTANCE----5 / 20 CM / 1M

INITIALIZE----5K / 15K / 25K / 35K / EXEC / OFF (in order to solve lens lose steps, when it focus certain times, the

module will auto check itself again, EXEC means REBOOT AND SELFCHECK)

ZOOM START----1, means the zoom starting time of the zoom module

ZOOM END----30, mean the biggest zoom times of the zoom module (initialization can clear this set)

EXIT

WHITE BALANCE:

MODE----AUTO / SPECIAL / WAWB / OUTDOOR / INDOOR

R----1~255

B----1~255

EXIT

AGC:

AGC----AUTO / MANU

LEVEL----1~16

BEIGHTNESS----AUTO / 1~15

SHUTTER----AUTO / 1/50~10K

EXIT

MODE:

BLC----ON / OFF

D/N----AUTO / DAY / NIGHT

MIRROR----ON / OFF

PROTOCOL----VISTA / PELCO D (Don't change this protocol, otherwise you can not control the PTZ anymore)

EXIT

MENU MODE:

LANGUAGE----CHS/ENG

MENU TIR16

FRANGE:5M/3M/1M

CAMERA ID: 000 (optional)

ID DISPLAY: OFF / ON

FOCUS: AUTO / MANUAL

ZOOM START: 01 (changeable)

ZOOM END: 23 (changeable)

BLC: ON/OFF

ID: 1

FOCUS:

WHITE BALANCE:

AGC:

MODE:

MENU MODE:

IR LIGHT:

INITIALIZE: OFF

EXIT

MODE----PUSH / OFF / ON

ID----OFF / ON

FOCUS----OFF / ON

EXIT

IR LIGHT:

FUNCTION (MODE)----OFF / ON

IR LIGHT (LEVEL)----1 / 2 / 3 (IR light turn on set)

SWITCH----OFF / ON

ZOOM STAR----1 (changeable)

ZOOM END----30 (changeable)

EXIT

INITIALIZE: ON / OFF

EXIT

4.5 PAN setup

Shake the joystick up / down to make the cursor be under the "PAN SETUP" item, then press the key "Iris+" (or the key

"OPEN" / "ENTER" on the keyboard ) to confirm select this item, and enter the next sub menu: as the sheet:

SCAN SETUP

AUTO FLIP

HOME PLACE

4.5.1 Scan setup:

Shake the joystick up / down to make the cursor be under the "SCAN SETUP" item, then press the key "Iris+" (or the

key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, and enter the next sub menu: as the sheet:

PATTERN SCAN

TOUR SCAN

AUTO SCAN

LIMIT SCAN

Pattern scan setting:

Shake the joystick up / down to make the cursor be under the "PATTERN SCAN" item, then press the key "Iris+" (or the

key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, and enter the next sub menu: (as the sheet:)

PATTERN NUMBER 001 / 002

SET PATTERN

RUN PATTERN

USED STATE ENABLE / DISABLE

Pattern number--------shake the joystick up/down to change the scanning routes,(001—002), 2 routes are settable.

Set pattern--------select this item, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm

select this item, start to set route.(can remember route within 15 minutes, pattern your scan route)

Run pattern--------select this item, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to

confirm select this item, now the camera starting pattern scan action, and exit all menu.

Used state--------select this item, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm

select this item, shake the joystick up / down to select use this route or don't use. After finish the set, press the key "Iris-

" (or the key "CLOSE" / "RETURN" on the keyboard ) to exit this menu , and back to the previous menu.

Tour scan setting:

Shake the joystick up / down to make the cursor be under the "TOUR SCAN" item, then press the key "Iris+" (or the key

"OPEN" / "ENTER" on the keyboard ) to confirm select this item, and enter the next sub menu: as the sheet:

TOUR NUMBER 001 ~ 004 optional

SET TOUR

RUN TOUR

USED STATE ENABLE / DISABLE

Tour number--------shake the joystick up/down to change the scanning routes,(001—004), 4 routes are settable.

Set tour--------select this item, press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm select

this item, you can set continuous preset positions in this route, every route can set 16 preset positions

(Note: this function shortcut key and number can't use as preset positions ). You can set the speed

between every positions (50~128 level). You can set the stay time of every position (1~240 seconds).

Run tour--------press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to working this cruise scan, now

the camera starting cruise scan action, and exit all menu.

Used state--------select this item, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm

select this item, shake the joystick up / down to select use this route or don't use. After finish the set,

press the key "Iris" (or the key "CLOSE" / "RETURN" on the keyboard ) to back to previous menu.

Auto scan setting:

Shake the joystick up / down to make the cursor be under the "AUTO SCAN" item, then press the key "Iris+" (or the key

"OPEN" / "ENTER" on the keyboard ) to confirm select this item, and enter the next sub menu: as the sheet:

SCAN SPEED 060

SCAN POSITION

Scan speed: select this item, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm,

shake the joystick up / down to change the scan speed (10~80 level), default is 60th level.

Scan position: select this item, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm,

use the keyboard, you can adjust camera pitch angle and zoom, let the camera to remember it.

Limit scan:

Shake the joystick up / down to make the cursor be under the "LIMIT SCAN" item, then press the key "Iris+" (or the key

"OPEN" / "ENTER" on the keyboard ) to confirm select this item, and enter the next sub menu: as the sheet

SCAN SPEED 060

SCAN POSITION

LEFT LIMIT

RIGHT LIMIT

Scan speed: select this item, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm,

shake the joystick up / down to change the scan speed (10-80 level), default is 60th level.

Scan position: elect this item, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm,

use the keyboard, you can adjust camera pitch angle and zoom, let the camera to remember it.

Left limit: select this item, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm, shake

the joystick up / down to set the position (starting point).

Right limit: select this item, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm,

shake the joystick up / down to set the position (ending point).

4.5.2 Auto flip function

Shake the joystick up / down to make the cursor be under the "AUTO FLIP" item, then press the key "Iris+" (or the key

"OPEN" / "ENTER" on the keyboard ) to confirm select this item, select ON/OFF, the factory default is ON.

4.5.3 Home (Fixed) position

Shake the joystick up / down to make the cursor be under the "HOME " item, then press the key "Iris+" (or the key

"OPEN" / "ENTER" on the keyboard ) to confirm select this item, then you can use the keyboard to adjust the camera to

be the best condition, to set a fixed position as its home position.

4.6 Calendar setup

Shake the joystick to operate, press "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm select this item,

and enter the sub menu.

TIME SET

TIME DISPLAY DISPLAY / OFF

TIMINGACTIONNO. 001

TIMING ACTION TIME 010

TIMINGACTION NOTHING

TIME SET: select this item, then press "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm, move joystick

up / down to change time (YY/MM/DD HH:MM)

TIME DISPLAY: select this item, then press "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm, move

joystick up / down to change display mode, default set is "OFF".

TIMING ACTION NO.: select this item, then press "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm,

move joystick up / down to change action number for certain time (001~008), camera support 8 timing set.

TIMING ACTION TIME: select this item, then press "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm,

move joystick up / down to change the time you when you want certain action, camera support 24 hours

timing set.

TIMING ACTION: select this item, then press "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm, move

joystick up / down to change the action you want at the time you set. Camera support actions as: NOTHING

/ PATTERN SCAN / TOUR SCAN / LEF, RIGHT LIMIT SCAN / AUTO SCAN / HOME PLACE. When you

finish set, press "Iris+" (or "OPEN" / "ENTER" on the keyboard) to confirm and save your set.

4.7 Call the shortcut of preset positions (Pelco-D/P protocol)

Some shortcuts can realized by calling preset positions to using some functions:

Preset position Function

Call 59# or 95# preset position Enter main menu

Call 34# preset position Back to initial position

Call 38# preset position 360° auto scan

Set 40# preset position Delete all preset positions

Preset position number of tour scan route, and call / delete command

Tour scan route Call command Corresponding number of preset position

No.01 Call 41# preset position No. 1—16# preset position

No.02 Call 42# preset position No. 17—32# preset position

No. 03 Call 43# preset position No. 65—80# preset position

No. 04 Call 44# preset position No. 113—128# preset position

No. 05 Call 45# preset position No. 129—144# preset position

No. 06 Call 46# preset position No. 145—160# preset position

No. 07 Call 47# preset position No. 161—176# preset position

No. 08 Call 48# preset position No. 177—192# preset position

Preset position number of pattern scan, and call / delete command

Pattern scan route Call command

No.01 Call 51# preset position

No.02 Call 52# preset position

Starting limit scan Call 53# preset position

Indoor & Outdoor Normal High Speed Dome Camera (W/O IR)

1. Features

zRotating speed: horizontal 0.1°~220°/sec, vertical 0.1°~160°/sec

z128 preset positions, some models can set camera title

z2 scan modes, 4 cruise routes, 2 pattern scan routes

z2 alarm input,2 alarm auxiliary switch output (need to choose when you order the product)

zRS485 communication, auto identify protocol as Pelco D / P

zChinese / English OSD menu

zBuilt-in the setting function of idle action

zDisplay the camera location coordinates and zoom multiples

zWaterproof cover level: IP66

zBuilt-in constant temperature control system

z2 installation methods: Drop ceiling installation, wall mounted installation

zWorking temperature: -20° C--+65° C

zWorking humidity: less than 95%

zPower: DC12V/5A

2. Mounting size drawing

2.1 Wall mount

2.2 hoisting mount

3. hardware setting

3.1 Dial codes switch setting

Open the codes cover on top of dome cover, see the dial codes of 10 numbers, you can turn every number ON or OFF

3.2 Baud rate setting

High speed dome camera can auto identify the Pelco-D / Pelco-P, then starting work, so you just need to set baud rate

and address codes of the camera, it can starting normal working. Baud rate can set through the 9th ~10th dial codes,

setting method as below: factory default as 2400bps.

Baud rate and dial codes switch matching sheet

Dial codes 2400 bps 4800 bps 9600 bps 19200 bps

No. 9 OFF ON OFF ON

No. 10 OFF OFF ON ON

3.3 Address codes setting

10numbers dial codes switch, (picture 01) No.1~ No.8 are use to set the address codes, you can set address codes

within the range 1~256, factory default as 1. Use binary, dial every number to be "ON" is means as 1, dial to be "OFF"

is means as 0, details please reference the sheet.

Address codes and dial codes switch sheet (Binary), calculate it according to this sheet

Binary Add Binary Add Binary Add Binary Add

0000000 0 11110000 15 01111000 30 10110100 45

10000000 1 00001000 16 11111000 31 01110100 46

01000000 2 10001000 17 00000100 32 11110100 47

11000000 3 01001000 18 10000100 33 00001100 48

00100000 4 11001000 19 01000100 34 10001100 49

10100000 5 00101000 20 11000100 35 01001100 50

01100000 6 10101000 21 00100100 36 11001100 51

11100000 7 01101000 22 10100100 37 00101100 52

00010000 8 11101000 23 01100100 38 10101100 53

10010000 9 00011000 24 11100100 39 01101100 54

01010000 10 10011000 25 00010100 40 11101100 55

11010000 11 01011000 26 10010100 41 00011100 56

00110000 12 11011000 27 01010100 42 10011100 57

10110000 13 00111000 28 11010100 43 01011100 58

01110000 14 10111000 29 00110100 44 11011100 59

If you use other equipments to control the camera, because of the protocol limitation, some special function maybe

cannot use. When you use other equipments to control the camera, you need to set the protocol (auto identify), baud

rate, address codes to be right. Different factories have different address codes, so sometimes you need to add 1 or cut

1 when you setting address codes. For example, you set the address code of camera to be 2, then you need to set

DVR controlling address code to be 3 or 1, then you can control it.

Remarks: alarming output switch always opening, K1~K8 are use to connect outside input signal

4. OSD menu setting

4.1 menu setting operating introductions

When the camera power on, its basic informations will display, like protocol, baud rate, address code. After finish the

checking and accept your controlling, these informations will disappear. ( user can see all setting info at here ) OSD

menu setting method:

Enter the main OSD menu: call #59 / #95 preset position to enter the main menu, then can set every item.

Use the keyboard: call 59 / 95 number keys (call preset position) to enter main menu, then shake the joystick to shift up

/ down / left / right ( ←↑→↓ ), every keys functions as below:

menu setting functional keys

No. Original functions of the keyboard Functions after enter the OSD menu

1 joystick: up Menu cursor: up

2 joystick: down Menu cursor: down

3 joystick: left Menu cursor: left

4 joystick: right Menu cursor: right

5 Iris close/ Iris (Iris - ) Menu: back

6 Iris open/ Iris (Iris + ) Menu: enter

4.2 Basic introduction

4.2.1 Select item

Use the keyboard: call 59# / 95 # preset position to enter main menu, then see a sheet as below:

Use the joystick up / down to select item, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to

confirm select this item, or enter the next sub menu:

Change the language to be English: move the joystick down to the bottom, press the key "Iris+" (or the key "OPEN"

on the keyboard ) to confirm select the item of "LANGUAGE", shake the joystick to change language to be "ENGLISH".

SYSTEM SETUP

CAMERA SETUP

PAN SETUP

CALENDAR

LANGUAGE ENGLISH

4.2.2 Parameters setting operation

Shake the joystick up / down to change number of every item, press the key "Iris+" (or the key "OPEN" / "ENTER" on

the keyboard ) to confirm select this item and save this setting.

Press the key "Iris-" (or key "CLOSE" / "RETURN" on the keyboard ) to exit this menu, or back to the previous menu.

4.3 System setting of the dome camera

Shake the joystick up / down to make the cursor be under the "SYSTEM SETUP" item, then press the key "Iris+" (or the

key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, or enter the next sub menu: as the sheet:

INFO DISPLAY

SYSTEM ACT

SET DOME TITLE

4.3.1 Info display setting

Shake the joystick up / down to make the cursor be under the "INFO DISPLAY" item, then press the key "Iris+" (or the

key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, or enter the next sub menu: as the sheet:

TITLEINFO OFF

COORDINATE OFF

TEMPERATURE OFF

Shake the joystick up / down to select, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to

confirm select this item.

CAMERA

TITLE ON/OFF

COORDINATE ON / OFF

TEMPERATURE ON / OFF

ZOOM OFF

Press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, then shake the

joystick up / down, you can select "DISPLAY" or "OFF". Finish the setting select, press the key "Iris+" (or the key

"OPEN" / "ENTER" on the keyboard ) to confirm and save your set value. You can press the key "Iris-" (or the key

"CLOSE" / "RETURN" on the keyboard ) to exit this menu , and back to the previous menu.

4.3.2 System act setting

Shake the joystick up / down to make the cursor be under the "SYSTEM ACT" item, then press the key "Iris+" (or the

key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, or enter the next sub menu: (as the sheet:)

POWER UP ACT NOTHING

LEISURE ACT NOTHING

LEISURE TIME 003~240 (SECONDS)

RESET

Power up act: means after camera power on and finish checking, the action that users want it to do, the factory default

is "nothing (no any action)":

Shake the joystick up / down to make the cursor under the "POWER UP ACT" item, press the key "Iris+" (or the key

"OPEN" / "ENTER" on the keyboard ) to confirm select this item, then shake joystick up / down to select what action you

want, there are 10 options can be selected: nothing / pattern scan route / cruise route scan / limiting position scan/ auto

scan/ fixed position scan (home). Select one, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard )

to confirm and save your set value. You can press the key "Iris-" (or the key "CLOSE" / "RETURN" on the keyboard ) to

exit this menu, and back to the previous menu.

Leisure act: means the camera haven't any actions after a period of time which you set, if you don't control it beyond

this time, it will auto working a action you set before. The factory default is "nothing":

Shake the joystick up / down to make the cursor be under the "LEISURE ACT" item, then press the key "Iris+" (or the

key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, then shake joystick up / down to select what action

you want, there are 10options can be selected: nothing / pattern scan route / cruise route scan / limiting position scan /

auto scan / fixed position scan. Select one, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard )

to confirm and save your set value. You can press the key "Iris-" (or the key "CLOSE" / "RETURN" on the keyboard ) to

exit this menu , and back to the previous menu.

Leisure time: (factory default is "30 seconds")

Shake the joystick up / down to make the cursor be under the "LEISURE TIME" item, then press the key "Iris+" (or the

key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, then shake joystick up / down to select time

(3~240 seconds). Finish the setting select, press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to

confirm and save your set value. You can press the key "Iris-" (or the key "CLOSE" / "RETURN" on the keyboard ) to

exit this menu, and back to the previous menu.

Reset:

Shake the joystick up / down to make the cursor be under the "SYSTEM RESET" item, then press the key "Iris+" (or the

key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, then screen appears "?", you need to enter the

camera secret codes, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm, 2 seconds

later, the camera will restore to factory defaults.

Set camera title:

Shake the joystick up / down to make the cursor be under the "SET DOME TITLE" item, then press the key "Iris+" (or

the key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, then screen appears "?", shake the joystick up

/ down to select the letters (a~z, A~Z) and numbers (0~9) you want, move the joystick left or right will move the cursor

location, then press the key "Iris+" (or the key "OPEN" / "ENTER" on the keyboard ) to confirm.

4.4 Camera setup

Shake the joystick up / down to make the cursor be under the "camera setup" item, different camera have different

parameters for selection, different modules have different menu. Our standard module menu generally as below:

After enter the main menu, you can choose these menu items as below by the key "zoom" (the key "zoom" original

function is for change the image zoom definition ), or use the joystick, use "focus" to change value.

F RANGE: 5M /3M /1M--------the range of the FOCUS

CAMERA ID: 000:--------000-255(selectable by useing the key "zoom")

ID DISPLAY: ON/OFF:--------"ON" means display, "OFF" means no display(selectable by useing the key "zoom")

FOCUS: MANUAL/AUTO: --------manual zoom (defaults)/ auto zoom(selectable by useing the key "zoom")

ZOOM START: 01:--------default is 01X,(selectable by useing the key "zoom")

ZOOM END: 23:--------default is 23X,(selectable by useing the key "zoom")

MENU TIR16

FRANGE:5M/3M/1M

CAMERA ID: 000 (optional)

ID DISPLAY: OFF / ON

FOCUS: AUTO / MANUAL

ZOOM START: 01 (changeable)

ZOOM END: 23 (changeable)

BLC: ON/OFF

ID: 1

FOCUS:

WHITE BALANCE:

AGC:

MODE:

MENU MODE:

IR LIGHT:

INITIALIZE: OFF

EXIT

BLC: ON/OFF:--------back light compensation is selectable,ON/OFF(selectable by useing the key "zoom")

RESET:--------restore factory settings

EXIT:--------return

ID: --------ID of every camera, in order to control all cameras more conveniently, from 1~255

FOCUS: FOCUS MODE----AUTO: real time, default; MANU: manual focus; PUSH: find image clear point when the

zoom stopping, then focus, will not focus again. (MANUAL MODE, if change zoom, focus mode will auto change to

AUTO FOCUS MODE; AUTO MODE, if change zoom, focus mode will auto change to MANUAL FOCUS MODE)

FOCUS DISTANCE----5 / 20 CM / 1M

INITIALIZE----5K / 15K / 25K / 35K / EXEC / OFF (in order to solve lens lose steps, when it focus certain times, the

module will auto check itself again, EXEC means REBOOT AND SELFCHECK)

ZOOM START----1, means the zoom starting time of the zoom module

ZOOM END----30, mean the biggest zoom times of the zoom module (initialization can clear this set)

EXIT

WHITE BALANCE: MODE----AUTO / SPECIAL / WAWB / OUTDOOR / INDOOR

R----1~255

B----1~255

EXIT

AGC: AGC----AUTO / MANU

LEVEL----1~16

BEIGHTNESS----AUTO / 1~15

SHUTTER----AUTO / 1/50~10K

EXIT

MODE: BLC----ON / OFF

D/N----AUTO / DAY / NIGHT

MIRROR----ON / OFF

PROTOCOL----VISTA / PELCO D (Don't change this protocol, otherwise you can not control the PTZ anymore)

EXIT

MENU MODE: LANGUAGE----CHS/ENG

MODE----PUSH / OFF / ON

ID----OFF / ON

FOCUS----OFF / ON

EXIT

IR LIGHT: FUNCTION (MODE)----OFF / ON

IR LIGHT (LEVEL)----1 / 2 / 3 (IR light turn on set)

SWITCH----OFF / ON

ZOOM STAR----1 (changeable)

ZOOM END----30 (changeable)

EXIT

INITIALIZE: ON / OFF

EXIT

4.5 PAN setup

Shake the joystick up / down to make the cursor be under the "PAN SETUP" item, then press the key "Iris+" (or the key

"OPEN" / "ENTER" on the keyboard ) to confirm select this item, and enter the next sub menu: as the sheet:

SCAN SETUP

AUTO FLIP

HOME PLACE

4.5.1 Scan setup:

Shake the joystick up / down to make the cursor be under the "SCAN SETUP" item, then press the key "Iris+" (or the

key "OPEN" / "ENTER" on the keyboard ) to confirm select this item, and enter the next sub menu: as the sheet:

PATTERN SCAN

TOUR SCAN

AUTO SCAN

LIMIT SCAN

Pattern scan setting:

Shake the joystick up / down to make the cursor be under the "PATTERN SCAN" item, then press the key "Iris+" (or the