DeView ATMP7W User manual

Installation
Choose an appropriate bracket from the two included
(Short or Long).
To change the bracket, remove the screws on each side of the
camera, remove the current installed bracket and then replace it
with a new version. Reinstall the attaching screws to secure the
bracket to the camera.
For specific locations, there are two extended arms which will
allow the camera to be positioned forward.
1. Remove the bracket by loosening the securing screws and
axis screws on both sides.
2. Place the two extended arms and secure the supplied axis
screws to the camera. Then set the positioning screws back
onto the camera.
Note: slightly tighten the axis screw and make sure the
extended arms are still rotatable.
3. Use the axis screws to install the bracket onto the extended
arms and then secure the positioning screws. Adjust the
position required and tighten the positioning screws so as to
fix the camera to the desired view angle.
Note: Some installations require the bracket to be installed in
the ATM machine before attaching to the camera.
In the accessory bag you have securing screws or thumb knobs
that can be used to secure the camera. Choose which works
best for the installation. Once the camera is mounted and
positioned, secure the camera by tightening screws.
Connection
Dual Voltage Version
Mount dual power board in desired location then attach the
camera lead. Next use the wire ended barrel plug to attach the
appropriate power source and plug into the mating connector
coming off the dual power board. Attach video cable and
installation is complete.
12VDC Version
Attach the camera lead then use the wire ended barrel plug to
attach the appropriate power source and plug into the mating
connector in the wire harness. Attach video cable and
installation is complete.
Make sure power is off before any connection is made.
Camera Installation and Connection
700TVL High Resolution
ATM Surveillance Camera Parts and Descriptions
24VAC/12VDC
Video Output
Camera Lead Connector
Dual
Power Board
* Supplied with Dual Power model only
** 12VDC only model cannot connect to dual power board
ATM
Surveillance Camera
OSD
Control Board
OSD
Control Board Cable
Long
Bracket
Extended
Arms
Wire-ended Power
Adaptor Lead
Camera Lead
Connector
* Supplied with 12VDC model only
** 12VDC: connect directly to camera
Screw Accessories
*2 Knurling Knobs
*4 Black Screws
*4 Silver Shoulder Screws
*1 Top Thumb Screw
12VDC
Video Output
Short
Bracket
OSD Control Connector
Camera Lead Connector
Remove the bracket from the camera
1
2
Set up the extended arms
3
Secure the bracket and the extended arms onto the camera
Bracket Adjustments
4
Installation
Short Bracket Long Bracket
Short Bracket
with Extended Arms
Long Bracket
with Extended Arms
Note: There are multiple mounting positions on the extended arms which provide flexible mountings to different ATM machines.
V531-KA005-S00
VER.06/2015
www.devieweurope.com
ATM Surveillance Camera
User Manual

The OSD Control Board and
With power applied to the camera and a video monitor
connected, press and hold the [ENTER] key for three
seconds to access the OSD top level menu. A map of
the setup menu options will be shown as the right of this
sheet presented.
To navigate through the menus, use the arrow keys on
the control board and use the [ENTER] key to select the
menu field desired.
IMPORTANT:
When any changes made to the camera configuration, use
the “SAVE SETTINGS” option in the “SAVE/RESTORE”
menu to save. Otherwise any changes made will be lost
when the camera is next reset or has its power cycled.
OSD Control Board with Cable
OSD
Control Board
OSD
Control Board Cable
LEFT RIGHT
DOWN
ENTER
UP
ATM
Surveillance Camera
Camera Lead Connector
OSD Control Connector
Connect the OSD Control Board Cable to the
OSD Control Board (see image below)
Connect the OSD Control Board to the
Camera (see image below)
Focal Length
2.8mm 2.5mm
F-No. F1.8 F2.5
Iris Range
Fixed Range
Angle Of View :
Diagonal 128.0º 142.7º
Horizontal 98.0º 113.4°
Vertical 81.5º 85.9°
Lens Specifications
FCC COMPLIANCE:
This equipment complies with Part 15 of the FCC rules for intentional radiators and
Class B digital devices when installed and used in accordance with the instruction
manual. Following these rules provides reasonable protection against harmful
interference from equipment operated in a commercial area. This equipment should
not be installed in a residential area as it can radiate radio frequency energy that could
interfere with radio communications, a situation the user would have to fix at their own
expense.
CISPR 22 WARNING:
This is a Class B product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
POWER SUPPLY REQUIREMENTS:
For use with listed Audio/Video Product and only connected to 15W or less power supply.
Power supply should be a NEC Class 2 / LPS Supply.
EQUIPMENT MODIFICATION CAUTION:
Any equipment changes or modifications not expressly approved by the seller could cause
a hazardous condition and invalidate FCC compliance, thus voiding the users authority to
operate the equipment.
Regulatory Compliance
Control Menu Map
Press the [ENTER] key on the control board for three seconds to view the menu.
SCENE SELECT FULL AUTO
INDOOR
OUTDOOR
BACKLIGHT
ITS
CUSTOM
AE LEVEL 001 ~ 250
6.0DB ~ 44.8DB
AUTO / OFF
256FLD ~ 1/10000
6.0DB ~ 44.8DB
256FLD ~ 1/10000
6.0DB ~ 44.8DB
AGC MAX
SENS UP
SHUTTER
AGC MAX
WHITE BAL
SHUTTER /
AGC
MANUAL
HLC/BLC OFF
HLC CLIP LEVEL
ATW (*1)
PUSH
USER1
SPEED
DELAY CNT
ATW FRAME
ENVIRONMENT
RGAIN
PAGE1
AUTO
SHUTTER
AGC MAX
FIX
ANTI CR AUTO/OFF/ON
ON/OFF
DIS
PICT ADJUST
SHARPNESS
HUE
COLOR GAIN
BRIGHTNESS
CONTRAST
EXIT
SYS SETTING
ON POS
SYNC MODE
LENS
COMMNUNICATION
CAMERA ID OFF
INT/LL(*6)
MANUAL
AUTO
FLIP OFF/V/H/VH
LCD/CRT
TYPE
MODE
ADJUST
SPEED
ADDRESS
PROTOCOL
BAUDRATE
DATABIT
PARITY
STOPBIT
000 ~ 255
001∼255
001∼255
000 ~ 255
INDOOR / SUNNY / SHADE / AUTO
000 ~ 255
DAY/NIGHT DAY
NIGHT
BURST
BURST ON/OFF
ON/OFF
INT/EXT1/EXT2CNTL SIGNAL
DELAY CNT
DAY->NIGHT
NIGHT->DAY
AUTO
LENS SHD COMP
SET1 / SET2 / SET3
000 ~ 959
PATTERN
POSH
POSV
OFF
ON
000～490
DEFOG(*5)
LEVEL LOW / MID / HIGH
OFF
ON
EZOOM OFF
ON MAG/PAN/TILT
PRIVACY MASK
AREA SEL 1~15
DISPLAY
POSITION
COLOR
TRANSP
MOSAIC
OFF / ON
WHITE / BLACK / RED /GREEN / BLUE /
YELLOW / CYAN / MAGENTA
0.00 / 0.50 / 0.75 / 1.00
OFF / ON
PAGE2
LANGUAGE
VERSION
MAINTENANCE
EXIT
ENGLISH/中文/ESPANOL/PORTUGUES/PYCCKNN/FRANCAIS/DEUTSCH/日本語
W.PIX MASK
SAVE
NOT SAVE
CANCEL
BACK
MANUAL REGISTRATION
REG.POINT
CURSOR COLOR
BLINK
REG.NUMBER
AUTO
DATA CLEAR
RUN
BACK
CAMERA RESET
IR OPTIMZER OFF
ON MODE AUTO
CENTER
TOP
BOTTOM
IR AREA
LEVEL
﹍﹍﹍﹍﹍﹍
0-12
0~ 6
0~ 6
0~ 8
0~ 8
00~ 15
000 ~ 255
IR LED
FIX
DAY/NIGHT LEVEL MIN
LEVEL
LEVEL MAX
OFF
ON COLOR GAIN
PATTERN
POSH
POSV
LEVEL
COLOR NIGHT
IR SHADE COMP
OFF
001 ~ 255
001 ~ 255
LOW / MID / HIGH
SET1 / SET2 / SET3
000 ~ 959
000～490
OFF / LOW / MID / HIGH
OFF
ON
LEFT
RIGHT
WEIGHT
FLK LESS
MODE GAIN CNTL
SHUTTER FIX
MODE GAIN CNTL
SHUTTER FIX
ON
OFF
AUTO
MOTION DET OFF DETECT SENSE
INTERVAL
BLOCK DISP
MASK AREA
MOTION AREA MODE
AREA SEL
TOP
BOTTOM
LEFT
RIGHT
ON
1~4
BGAIN
USER2 RGAIN
MANUAL
PUSH LOCK
000 ~ 255
000 ~ 255
00 ~ 63
000 ~ 255
BLC(*2)
WDR/
ATR-EX(*3) LOW / MID / HIGH(*4)
LOW / MID / HIGH / OFF
DNR LEVEL 0 ~ 6
BGAIN
LEVEL
OFF
ATR-EX
WDR
CONTRAST
CLEAR FACE
CONTRAST
OFF / LOW / MID / HIGHCLEAR FACE
LOW /MID / HIGH
Menu Description
– The six modes can be selected.
– This Camera system provide functions that enable users to easily adjust the
image quality to suit the image output device used.
– Adjust the digital zoom
– This mode turns off the auto scene recognition. All functions canbe set and
adjusted manually
– Adjusts the brightness.
– Adjusts the image contrast (light and shade differences).
– Adjusts the sharpness.
– Adjusts the hue.
– ON / OFF.
– Magnification rate = ZOOM (0~255)
– Horizontal position settings.
– Vertical position settings.
– Select mask area (1-15).
– Mask to ON or OFF.
– Sets the color blend: RED/ GREEN/ BLUE/ YELLOW/ CYAN/ MAGENTA/
WHITE/ BLACK
– Sets the brightness blend ratio: 0%, /50%/75%/100%
– Open or close the mosaic function
DETECT SENSE
– Select mask area (1-15).
– Sets the MD detection interval. Subjects are detected when an interval
exceeding the set number of fields has elapsed from the previous motion
detection.
– Motion detection result frame display selection.
Outputs the results of the motion detected in each block.
– MD (Motion Detection) setting menu, for setting the no-detection area.
MONITOR AREA
– Sets the position of the monitoring frames in pixel or line increments.
– External synchronization is a function with synchronization of the phase
between an output video signal and an external reference signal. Use line
lock mode to minimize color rolling.
– Set the lens type.
– Select digital Flip / Rotate state Off / V(Top / bottom reversal) / H(Left / right reversal)
/ HV(Rotation by 180 degrees)
– Set the monitor type LCD or CRT.
COMMUNICATION (OPTION)
– Sets the position of the monitoring frames in pixel or
line increments.
– Sets the camera ID to ON or OFF.
– Save the settings (settings are saved).
– Exit menu without saving.
– Changes (restore settings to those selected when the menu was displayed).
– Return to previous menu.
– Return to page on the hierarchical level immediately before.
– LANGUAGE select between: English, Chinese Spanish, Russian, Portuguese,
German, French, Japanese.
– Version Display
– Digital Image Stabilizer.
– The mask function hides one or more areas which the user does not want
to be displayed on the screen.
– By using the motion detection function, it is possible to create surveillance
cameras which are capable of detecting moving objects.
– Adjust the color gain.
.
– This mode supports various shooting scenes. It is not specialized to any
particular scene, so it allows average shooting in any situation.
– This mode is specialized to indoor scenes, such as indoor shop surveillance.
It allows natural shooting with high contrast.
– This mode is specialized to outdoor scenes, Such as outdoor plaza surveillance.
.
It allows natural shooting with high contrast.
– This mode is specialized to scenes that mix indoor and outdoor conditions,
such as entranceway surveillance.
– Monitoring and optimizing model of road.
SCENE SELECT
SETUP MENU
PICT ADJUST
EZOOM
CUSTOM
Brightness
Contrast
Sharpness
Hue
Color Gain
EZoom
MAG
PAN
TILT
AREA SEL
DISPLAY
POSITION
– Privacy regional choice
COLOR
TRANSP
MOSAIC
INTERVAL
BLOCK DISP
MASK AREA
SYNC MODE
LENS
FLIP
LCD / CRT
CAMERA ID
SAVE
NOT SAVE
CANCEL
BACK
RETURN
DIS
PRIVACY MASK
MOTION DET
FULL AUTO
INDOOR
OUTDOOR
BACKLIGHT
ITS
SYS SETTING
EXIT-MENU
LANGUAGE
VERSION
MAINTENANCE
– Equipment maintenance
W.PIX MASK – W.PIX Repair set
CAMERA RESET – Reset the camera
TV System
Image Sensor
Resolution
Scanning Frequency
Effective Picture
Video Output
S/N Ratio
Storage Temperature
Operating Temperature
Power Source
NTSC
Sony 1/3" Super HAD-II Wide Dynamic
976(H) x 494(V) 976(H) x 582(V)
60Hz 50Hz
700 TVL
12 VDC ±10% / 24 VAC ±20%
Power Consumption 2.2W Max.
-10°C ~ +50°C
-20°C ~ +60°C
Input Terminal
DC Jack with fly lead attached
Minimum Illumination
0.3Lux(F1.2,50IRE,AGC ON)
General Specifications
Composite (75 BNC unbalanced connector)
Ω
PAL
50dB (100 IRE, F1.2)
Sense Up
Functional Specifications
NTSC: 1/60 ~ 1/100000 PAL: 1/50 ~ 1/100000
SDN(AUTO ,COLOR ,NIGHT)
Indoor：1800K~10500K Outdoor：6500K~10500K
INT /LL
4 Areas
Full Range
44.8 dB
ON/OFF
Up to 15 Masks
3D DNR
255X Max
ON/OFF
1/50 (1/60), 1/120 (1/100), 1/250, 1/500, 1/1K, 1/2K, 1/4K, 1/10K
OFF/V-FLIP/H-FLIP/HV-FLIP
ON/OFF
OFF/ATR-EX/WDR
ATW / Manual / Push / Push Lock / USER1,2
Auto White Balance Range
White Balance Control
Backlight Compensation (BLC)
Sync System
Privacy Zone
Motion Detection
Shutter Speed
AES
MES
AGC Gain Control
Day/Night
High-Light Compensation (HLC)
Digital Noise Reduction
Digital Zoom
DIS
ON / OFF
Wide Dynamic Range (WDR)
Mirror
Defog
12 VDC ±10%
This can not be changed except CUSTOM mode.
- CE:
--EN55022
--EN55011
- FCC:
--47 CFR Part15 Subpart B
--ANSI C63.4
--ICES-003
- CE:
--EN55024
--EN50130-4
Emissions:
Immunity:
Programming