Sussex SCALA User manual

SCALA
WALL BATH/BASIN MIXER
OUTLET SYSTEM: DRESS KIT
Tapware is to be installed by a Licensed Plumber in
accordance with AS/NZS 3500:2003
Water pressure is not to exceed 750 Kpa
Recommended working water pressure 300 - 500 Kpa.
Maximum water temperature is 65 deg.C.
To complete installation, operate the Mixer(s) checking the flow of both hot and cold water from the Outlet.
Check all fittings and fixtures for water leaks
NOGGIN
80 mm
B/Plate
Finished
Wall Surface
Set
Screw
Handle
Body
Handle
Pin
Apply Silicone
56mm
Dress
Ring
Masterfit
Apply Silicone
Stud Face
MIXER DRESS KIT
- Remove Mixer protective cover.
- Using silicone, seal the wall surface around
the Mixer and Outlet threads.
- Apply a small amount of silicone to the rear
of the backplate prior to mounting onto the wall.
- After Backplate has been mounted, fit the
Mixer Dress Ring.
- Fit the Handle Body onto the Mixer Cartridge
Lever and ensure full engagement.
- Secure the Handle Body by tightening the
Set screw using the Allen Key provided
(tighten well).
- Attach the Handle Pin.
NOTE: Apply a small amount of silicone or
adhesive to the thread of the Handle Pin to
prevent the Pin from becoming loose.
OUTLET FIT OFF
- Apply sealing tape (Teflon) to male thread.
- Place Dress Ring and Dress Flange over prepared
male thread.
- Fit and align the Outlet.
NOGGIN
Backplate
Dress Ring
Masterfit
Stud Face
Finished
Wall Surface
Dress Flange
Bath Outlet
INSTALLATION GUIDE
CRAFTED IN MELBOURNE
SUSSEXTAPS.COM.AU

WALL BATH/BASIN MIXER OUTLET
SYSTEM RH: ROUGH-IN
Tapware is to be installed by a Licensed Plumber in
accordance with AS/NZS 3500:2003
Water pressure is not to exceed 750 Kpa
Recommended working water pressure 300 - 500 Kpa.
Maximum water temperature is 65 deg.C.
ROUGH IN PLUMBING
Prior to installing calculate the finished Wall thickness, maximum is 30mm thick.
If Wall thickness is greater than 30mm, contact manufacturer for further options.
Prepare a Nogging to be fixed parallel between the Wall Studs.
The Nogging must be fitted to enable the base of the Masterfit to be 30-32mm back from the Stud Face
The Masterfit will be marked "This side Up" to indicate orientation.
Using the screws (x4) provided, mount the Masterfit to the Nogging. Ensure the Masterfit is level and square.
Pipe Connections
The Hot and Cold ports are marked on the Masterfit. (Mixers have individual Hot/Cold inlet ports).
Flush all water feed lines. All lines must be free from any dirt and debris before connecting to the Masterfit.
Connect Hot and Cold lines to the corresponding1/2" BSP ports of the Masterfit. (see Drawing )
Do not remove or disturb any factory fitted pressure plugs or Fixings.
Once all water connections are made, check Hot/Cold water flow by operating the Mixer Cartridge.
Check all fittings and fixtures for leaks.
Leave the Mixer(s) in the closed position and replace the Mixer protective cover.
Store the Dress Kit in a safe place until required (see Dress Finishing Guide)
PLUMBER NOTE:
On-site high pressure line testing must be conducted with the Mixer in the closed
position. (STATIC TEST ONLY)
Under no circumstances is the Mixer to be opened when exceeding the maximum
stated water pressure.
At the completion of the testing, do not relieve any high pressure by opening the Mixer.
Exposing the internals of the Mixer Cartridge to higher than specified water pressures,
will void the manufacturer's warranty.
Masterfit
NOGGING
Back Plate
180 x 80 mm
56mm
Dress Ring
Handle
Body
1/2" BSP
Male Outlet 1
30-32mm
Wall Covering
Max. 30mm
View from above
90
70
2
4.5
Mixer
Stud face
Min.
8mm
This
side
UP
Outlet
Hot
Cold
Mixer Outlet
Pipe Connections
INSTALLATION GUIDE
CRAFTED IN MELBOURNE
SUSSEXTAPS.COM.AU