Suunto CB-71/STD User manual

en
SUUNTO COMBOS AND MECHANICAL
INSTRUMENTS
INSTRUCTION MANUAL
Combo Consoles I Console Compasses CB-71/STD and CB-71/DS
Depth Gauge SM-16 I Pressure Gauge SM-36

2
SUUNTO Combo Consoles
Introduction
The Suunto combo consoles for recreational use, allow you to create a personal combo according to your own specific
needs.Analog gauges, dive computers and compasses fit together like building blocks.
The combos consist of four main modules: the pressure gauge module, the instrument module and two different compass
modules.
The pressure gauge module is designed for the Suunto pressure gauges and it can also be used with the new Suunto Quick
Release (QR). The basic combinations are displayed below:

3
Assembling the Combo Modules
1
2
5
(5)
4
(3)
3
1. CB-ONE module front cover with SM-36 pressure gauge in place (see section CB-ONE Module assembly)
2. CB-IN-LINE module front cover
3. CB-end piece or CB-71/STD compass (optional)
4. CB-IN-LINE module back cover with instrument
5. CB-ONE module back cover or CB-71/DS compass (optional)

4
CB-ONE Module Assembly
The CB-ONE Module is designed to fit the Suunto SM-36 analog pressure gauges.
Before assembling the CB-ONE module the hose cover needs to be fitted on the pressure hose. The hose cover ensures
that the SM-36 pressure gauge fits properly on the CB-ONE module.
If the Suunto Quick Release is used, the hose cover is not to be used (See section CB-ONE module assembly using the
SUUNTO Quick Release).
After attaching the hose cover the pressure hose and gauge are assembled on the CB-ONE front cover according to the
picture.
After the pressure gauge is in place the CB-ONE back cover (or alternatively the CB-71/SK-7/DS compass) is attached with
four screws.

5
CB-ONE Module Assembly when using the SUUNTO Quick Release
If the SUUNTO Quick Release (QR) is used the hose cover should be attached on the high pressure hose below the female
end of the QR. The male part is attached to the pressure gauge which is then fitted onto the CB-ONE front cover according
to the picture below.
CB-IN-LINE Module Assembly
The CB-IN-LINE module fits the Suunto Vyper and Zoop dive computers or the SM-16 round depth gauge.
The Vyper locks in place on the IN-LINE module back cover. For the other instruments there are lugs on the back cover
aiding the orientation.
The Suunto Vyper and Zoop are delivered with a display shield.

6
SUUNTO Console Compasses CB-71/SK-7/STD and CB-71/SK-7/DS
The CB-71/SK-7 is available in two versions: the CB-71/SK-7/STD for attachment on top of the combo modules or the
Cobra dive computer, and the CB-71/SK-7/DS for attachment on the back side of the CB-ONE module.
Compass use for divers
General instructions
Usually a compass must be held precisely in a horizontal position, otherwise the needle will sting. The SK-7 compass may
however be inclined about ±30 degrees.
Sighting a compass bearing
Hold the compass so that the compass is in a horizontal position and the direction line points away from you. Turn with the
compass until the direction line points at your destination, then turn the direction ring until the magnetic North needle is
aligned between the slit marks. The front end of the direction line on the SK-7 shows your compass bearing, and as long as
the North needle is aligned between the slit marks, the direction points toward your destination. The SK-7 compasses also
have a side reading window, which also enables you to take a bearing by directing the compass towards the destination
and by reading the compass bearing from the side window. This bearing can be memorized by turning the direction ring to
that bearing.
Setting a given bearing or direction
The scale division on the SK-7 is 360 degrees clockwise from 0 degrees at North. Turn the direction ring until the front end
of the direction line is at the desired direction. Turn the compass until the needle falls between the slit marks. The direction
line now points in the desired direction.
Magnetic declination
Maps and marine charts are drawn in correlation to the geographic poles, while the magnetic compass needle is subject to
magnetic declination which varies according to the location.
General orientation on the diving site
Before diving, check the main compass bearings at the dive site, paying special attention to memorizing the direction of the
shoreline and bearings of landmarks that may be of importance.
Natural aids to underwater navigation
• The underwater extension of the shore’s inclination tells the diver if he is following the shoreline. Be careful however
as underwater ridges may lead you astray. Surface occasionally to check your position.
• The dip and stratification of rocks on the shore can often be followed over large areas under water.

7
• Sand ripples usually form long lines parallel to the shore.
• The direction of currents should be noted by their effect on algae or drifting particles. Use the compass to check the
bearing of the current.
• In shallow water, the sun’s direction can be seen from shadows on the bottom, or by looking towards the surface.
• Swimming in a straight line along the bottom is greatly facilitated if you can line up three distinctive objects in your line
of vision.As you reach the first one, line up a new one farther away, so that you again have three points determining
your course. This way you can counteract the effects of side current.
Compass Balancing
The horizontal and vertical components of earth’s magnetic field vary in different locations. For this reason Suunto compass-
es are balanced for 2 different zones. If the compass is used in an adjacent balancing zone the compass needle will tilt only
slightly. However, the farther the compass is used from it’s intended zone, the more the needle will tilt. In extreme situations
the needle might stick. For this reason it is very important to know in which country the compass will be used.
Compass zone map

8
SUUNTO Mechanical Gauges
Suunto depth gauge SM-16
Models available: 45 m, 70 m, 150 ft, 230 ft
Suunto pressure gauge SM-36
Models available: 300 bar and 4000 psi
Before usage
Depth gauge:
Before diving, check the position of the depth indicating pointer.Atmospheric conditions (altitude, temperature) may cause
the point to not indicate zero. If this is the case, turn the adjusting screw located at the right side of the gauge to align the
pointer to zero. The adjustment is to be made at the temperature of usage. Repeated unnecessary adjustments may cause
excessive wear to the seals and eventual leakage.
CAUTION!
Do not attempt to adjust the water entry port located at the left side of gauge. Tampering with the port can cause
damage to internal components. Do not pressure test gauge in air.Always immerse the gauge in water while pressure
testing it.
Pressure gauge:
The hose has an end fitting with 7/16” 20 UNF-thread. If your regulator has a different thread size in the high pressure (HP-
output) port, ask your dealer for the correct adapter.Always inspect the o-ring at the male thread to be sure it is clean and
undamaged before connecting it to the regulator.
Always turn your air supply on slowly.Always turn the pressure gauge dial face away from your face when turning on the
air supply.
Do not overtighten the hose at the gauge, the fitting is pressure proof even when tightened with fingers.
Service
Avoid subjecting the gauges to excessive shock loads such as those that might occur from being dropped or hit against an

9
immovable object. Do not subject the gauges to pressures beyond their maximum range. Temperature extremes can be
damaging. In general, the gauges should not be exposed to temperatures to which you would not expose yourself.
CAUTION!
After use, rinse the gauges or the console with fresh water and store them out of direct sunlight, in a dry place at room
temperature.
CAUTION!
Do not attempt to clean the gauges with anything other than water. Use of cleaning agents or compressed air can cause
permanent damage. The introduction of any probe into the water entry port of the depth gauge or the pressure relief
valve opening of the pressure gauge can also damage internal components.
Before prolonged storage the instruments should be removed from the console, rinsed with fresh water and stored
separately.
CAUTION!
Do not attempt to disassemble the gauges. Special tools and training are required to perform the adequate service.
The instruments must be serviced by an authorized dealer every second year or after 200 dives (whichever comes first).

10
Operating and Storage Temperatures
SM-16 Operating temperature 0° C to 40° C [32° F to 104° F]
Storage temperature -20° C to 50° C [-4° F to 122° F]
SM-36 Operating and storage temperature 0° C to 40° C [32° F to 104° F]
Technical Specifications
The Suunto depth gauge SM-16 complies with the prEN 13319 standard.
The tolerances for depth gauges are:
At 3m +0.8 / -0.4 m
At 6m +0.8 / -0.4 m
At 9m ±0.8 m
At 15m +1/ -1.2 m
At 30m +1/ -1.2 m
At 45m +1/ -1.5 m
At 60m +1 / -1.5 m
The SM-36 pressure gauges comply with the EN 250 standard.
The tolerances for pressure gauges, measured at decreasing pressure are:
At 40 bar ± 5 bar
At 100 bar ± 10 bar
At 200 bar ± 10 bar
At 300 bar ± 10 bar

11
Suunto Limited Warranty
Suunto warrants that during the Warranty Period Suunto or a SuuntoAuthorized Service Center (hereinafter Service Center)
will, at its sole discretion, remedy defects in materials or workmanship free of charge either by a) repairing, or b) replacing,
or c) refunding, subject to the terms and conditions of this Limited Warranty. This Limited Warranty is only valid and enforce-
able in the country of purchase, unless local law stipulates otherwise.
Warranty Period
The Limited Warranty Period starts at the date of original retail purchase. The Warranty Period is two (2) years for display
devices. The Warranty Period is one (1) year for accessories and consumable parts, including but not limited to chargeable
batteries, chargers, docking stations, straps, cables and hoses.
Exclusions and Limitations
This Limited Warranty does not cover: 1. a) normal wear and tear, b) defects caused by rough handling,
or c) defects or damage caused by misuse contrary to intended or recommended use; 2. user manuals or any third-party
items; 3. defects or alleged defects caused by the use with any product, accessory, software and/or service not manufac-
tured or supplied by Suunto; 4. replaceable batteries.
This Limited Warranty is not enforceable if item: 1. has been opened beyond intended use; 2. has been repaired using
unauthorized spare parts; modified or repaired by unauthorized Service Center; 3. serial number has been removed, altered
or made illegible in any way, as determined at the sole discretion of Suunto; 4. has been exposed to chemicals including but
not limited to mosquito repellents.
Suunto does not warrant that the operation of the Product will be uninterrupted or error free, or that the Product will work
with any hardware or software provided by a third party.
Access to Suunto warranty service
You must have proof of purchase to access Suunto warranty service. For instructions how to obtain warranty service, visit
www.suunto.com/warranty, contact your local authorized Suunto retailer, or call Suunto Help Desk [phone] (national
or premium rates may apply).

12
Limitation of Liability
To the maximum extent permitted by applicable mandatory laws, this Limited Warranty is your sole and exclusive remedy
and is in lieu of all other warranties, expressed or implied. Suunto shall not be liable for special, incidental, punitive or
consequential damages, including but not limited to loss of anticipated benefits, loss of data, loss of use, cost of capital, cost
of any substitute equipment or facilities, claims of third parties, damage to property resulting from the purchase or use of the
item or arising from breach of the warranty, breach of contract, negligence strict tort, or any legal or equitable theory, even if
Suunto knew of the likelihood of such damages. Suunto shall not be liable for delay in rendering warranty service.

SUUNTO HELP DESK
GLOBAL [phone]
USA (toll-free) [phone]
CANADA (toll-free) [phone]
www.suunto.com
© Suunto Oy 11/2005, 09/2006, 11/2011. All rights reserved.
Suunto is a registered trademark of Suunto Oy.