Suzohapp ARPEGE SECURITY SC-350 Release Note

Technical Handbook 019722-101 Rev. 05
i
SC-350/SC-360
Table of contents
1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . 1
1.2 FCC Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.3 Environmental Compliance . . . . . . . . . . . . . . . . . . . 1
WEEE Directive (valid in the EU only) . . . . . . . . . . . . . . . . . 1
1.4 Responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.5 About this Document . . . . . . . . . . . . . . . . . . . . . . . 2
1.6 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.7 Abbreviations/Acronyms . . . . . . . . . . . . . . . . . . . . . 2
1.8 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.9 Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Hazard Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Installation, Service and Maintenance . . . . . . . . . . . . 4
2.3 Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.4 Warning Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.2 Controls and Operation . . . . . . . . . . . . . . . . . . . . . . 6
3.3 Main Components. . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.4 Positional References. . . . . . . . . . . . . . . . . . . . . . . . 8
3.5 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . 8
3.6 Computer Communication. . . . . . . . . . . . . . . . . . . . 9
3.7 Accessories and Options . . . . . . . . . . . . . . . . . . . . 10
4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1 Installation Requirements . . . . . . . . . . . . . . . . . . . 12
5 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.1 Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2 Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.3 Functional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
>>>

Technical Handbook 019722-101 Rev. 05
ii
SC-350/SC-360
>>>
6 Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.1 Mechanical Description . . . . . . . . . . . . . . . . . . . . . 14
Coin disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Diameter cam. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Thickness cam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Hopper unit - SC-360. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Feed mechanism. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Thickness selector and thickness guide block . . . . . . . . . . . . 15
Swing mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.2 Electronic Description . . . . . . . . . . . . . . . . . . . . . . 17
6.3 CPU Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Reset logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Non-volatile memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Coin sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Coin level sensor (for SC-360 with automatic coin hopper) . 18
Safety switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.4 PSU Board and Transformer . . . . . . . . . . . . . . . . . 19
Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Regulators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Triacs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Miscellaneous. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.5 Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.6 RD/AUX Interface. . . . . . . . . . . . . . . . . . . . . . . . . 21
External start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Full batch indication (FBI) . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Coin feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
External coin pulse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Resetting a remote display . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7 Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.1 Master Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
To reset: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Protection of master reset. . . . . . . . . . . . . . . . . . . . . . . . . . . 22
>>>

Technical Handbook 019722-101 Rev. 05
iii
SC-350/SC-360
>>>
7.2 How to Enter, Change and Exit Set-up . . . . . . . . . . 23
Set-up functions (pages 1-8) . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.3 1 - Software Version and Memory Checks . . . . . . . . 24
Software version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Memory address space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Program memory check sum . . . . . . . . . . . . . . . . . . . . . . . . 24
EEPROM contents check sum . . . . . . . . . . . . . . . . . . . . . . . 24
Highest stack address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.4 2 - Reverse Sequence for Motor and Solenoid . . . . . 25
(a) 0-1 Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
(b) 0-2 Solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
(c) 0-6 Delay period and reverse period. . . . . . . . . . . . . . . . . 26
(d) 0-2 Reversing sequence . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7.5 3 - Miscellaneous Functions #1 . . . . . . . . . . . . . . . 27
(a) Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
(b) C and B+C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
(c) C, M and ACC+C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
(d) Reversing function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
7.6 4 - Adjustments to External Devices . . . . . . . . . . . . 28
(a) SC-350/360 and cascade . . . . . . . . . . . . . . . . . . . . . . . . . 28
(b) SC-350/360 and BDO sachet machine . . . . . . . . . . . . . . 28
(c) Not used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
(d) Not used. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
7.7 5 - Keypad Settings . . . . . . . . . . . . . . . . . . . . . . . . 28
(a) Stops the machine during batching . . . . . . . . . . . . . . . . . 28
(b) Zeroes RD (accessory) when C is pressed . . . . . . . . . . . . 29
(c) Zeroes RD (accessory) when M is pressed . . . . . . . . . . . . 29
(d) Adjusts Start/Stop-function. . . . . . . . . . . . . . . . . . . . . . . 29
7.8 6 - Computer Communication . . . . . . . . . . . . . . . . 29
(a) Not used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
(b) Debugging control programs . . . . . . . . . . . . . . . . . . . . . 29
(c) One character via the serial port . . . . . . . . . . . . . . . . . . . 29
(d) Disables the handshake signals . . . . . . . . . . . . . . . . . . . . 29
7.9 7 - Miscellaneous Functions #2 . . . . . . . . . . . . . . . 30
(a) and (b) Not used. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
(c) Fine tuning of reverse period. . . . . . . . . . . . . . . . . . . . . . 30
>>>

Technical Handbook 019722-101 Rev. 05
iv
SC-350/SC-360
>>>
(d) Batch in steps of 1,000 (1“). . . . . . . . . . . . . . . . . . . . . . . 30
7.10 8 - Adjustment of Sensitivity
of Hopper (SC 360). . . . . . . . . . . . . . . . . . . . . . . 31
(a), (b) and (c) Time delay settings . . . . . . . . . . . . . . . . . . . . 31
7.11 Accessing Statistics Registers. . . . . . . . . . . . . . . . . . 31
7.12 Service Intervals . . . . . . . . . . . . . . . . . . . . . . . . . . 32
To enable/disable the servicing function: . . . . . . . . . . . . . . . 32
3 - Number of coins counted . . . . . . . . . . . . . . . . . . . . . . . . 33
4 - Service interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5 - Setting the service interval . . . . . . . . . . . . . . . . . . . . . . . . 33
6 - Service interval mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Changing mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7 - Service interval demonstration mode. . . . . . . . . . . . . . . . 34
8 - Disabling service interval . . . . . . . . . . . . . . . . . . . . . . . . . 35
9 - Exiting the service interval menu. . . . . . . . . . . . . . . . . . . 35
7.13 Entering Password . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.14 Password Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Selection of password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Entering password menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Setting password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Disabling password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Exiting the password menu. . . . . . . . . . . . . . . . . . . . . . . . . . 37
7.15 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Text shown on display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8 Disassembly and Assembly . . . . . . . . . . . . . . . . . . . . . . 40
8.1 Exchanging Fuses . . . . . . . . . . . . . . . . . . . . . . . . . 40
8.2 Coin Guides - Removal . . . . . . . . . . . . . . . . . . . . . 41
Left coin guide, Fig. A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Right coin guide, Fig. B . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
8.3 Covers - Removal . . . . . . . . . . . . . . . . . . . . . . . . . 42
Top Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Bottom cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
8.4 Lid Switch - Removal. . . . . . . . . . . . . . . . . . . . . . . 43
8.5 Level Sensor - Removal . . . . . . . . . . . . . . . . . . . . . 43
8.6 Coin Chute - Removal . . . . . . . . . . . . . . . . . . . . . . 44
>>>

Technical Handbook 019722-101 Rev. 05
v
SC-350/SC-360
>>>
8.7 Hopper Unit - Removal . . . . . . . . . . . . . . . . . . . . . 45
8.8 Hopper Belt - Removal . . . . . . . . . . . . . . . . . . . . . 46
8.9 Hopper Motor - Removal. . . . . . . . . . . . . . . . . . . . 47
8.10 Coin Disc - Removal . . . . . . . . . . . . . . . . . . . . . . . 48
8.11 Coin Disc Drive - Removal . . . . . . . . . . . . . . . . . . 48
8.12 Diameter Selector Unit - Removal. . . . . . . . . . . . . . 50
8.13 Feed Unit - Removal . . . . . . . . . . . . . . . . . . . . . . . 51
8.14 Thickness Selector Unit - Removal . . . . . . . . . . . . . 52
8.15 Thickness Unit - Removal . . . . . . . . . . . . . . . . . . . 54
8.16 Thickness Guide Plate - Removal . . . . . . . . . . . . . . 55
8.17 Motor - Removal. . . . . . . . . . . . . . . . . . . . . . . . . . 55
8.18 Pulley Stand, Feed Unit - Removal . . . . . . . . . . . . . 56
8.19 Support Roller - Removal. . . . . . . . . . . . . . . . . . . . 57
8.20 Belt Stretcher Unit - Removal. . . . . . . . . . . . . . . . . 58
Belt stretcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Belt stretcher pulley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
8.21 CPU and PSU Board - Removal . . . . . . . . . . . . . . . 59
8.22 Solenoid - Removal . . . . . . . . . . . . . . . . . . . . . . . . 60
8.23 Count Sensor - Removal . . . . . . . . . . . . . . . . . . . . 61
8.24 Plates - Removal . . . . . . . . . . . . . . . . . . . . . . . . . . 62
9 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
9.1 Display is Blank at Switch On . . . . . . . . . . . . . . . . 63
9.2 Motor Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
9.3 Removing a Coin Blocking the Coin Exit. . . . . . . . . 64
9.4 Small Coins not Off-sorted. . . . . . . . . . . . . . . . . . . 64
9.5 Good Coins Off-sorted. . . . . . . . . . . . . . . . . . . . . . 64
9.6 Frequent Coin Jams. . . . . . . . . . . . . . . . . . . . . . . . 65
9.7 Miscount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
9.8 Batch Count Incorrect . . . . . . . . . . . . . . . . . . . . . . 65
9.9 Faulty Electronics . . . . . . . . . . . . . . . . . . . . . . . . . 65
10 Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
10.1 Exchanging the Feeding Belt. . . . . . . . . . . . . . . . . . 66
>>>

Technical Handbook 019722-101 Rev. 05
vi
SC-350/SC-360
>>>
10.2 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
10.3 Cleaning the Coin Track . . . . . . . . . . . . . . . . . . . . 67
10.4 Cleaning the Feeding Belt . . . . . . . . . . . . . . . . . . . 68
10.5 Exchanging Motor Drive Belt . . . . . . . . . . . . . . . . . 68
10.6 Exchanging Belt - Pulley Stands . . . . . . . . . . . . . . . 69
10.7 Exchanging Belt, Pulley Stand - Feed Unit . . . . . . . . 70
11 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
11.1 Coin Disc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
11.2 Thickness Guide Block . . . . . . . . . . . . . . . . . . . . . 72
Thickness guide block - Height position. . . . . . . . . . . . . . . . 72
Thickness guide block - Parallelism. . . . . . . . . . . . . . . . . . . . 73
11.3 Height Adjustment of the Coin Feed Belt . . . . . . . . 74
11.4 Feeding Belt Pressure . . . . . . . . . . . . . . . . . . . . . . 74
11.5 Coin Rail System. . . . . . . . . . . . . . . . . . . . . . . . . . 75
Left and Right Sorting Rails. . . . . . . . . . . . . . . . . . . . . . . . . . 75
Parallelism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
12 Computer Communication. . . . . . . . . . . . . . . . . . . . . . . 77
12.1 Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
12.2 Protocol Structure . . . . . . . . . . . . . . . . . . . . . . . . . 77
12.3 Logging On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
12.4 Logging Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
12.5 Reading Revision State for Software and Protocol . . . 79
12.6 Reading Program Information . . . . . . . . . . . . . . . . 80
12.7 Reading Counting Register . . . . . . . . . . . . . . . . . . . 81
12.8 Reading Memory Contents . . . . . . . . . . . . . . . . . . . 81
12.9 Transferring the Number of Counted Coins to Memory 81
12.10 Reading the Number of Counted Coins . . . . . . . . . 82
Revision 1.xx of the protocol: . . . . . . . . . . . . . . . . . . . . . . . 82
Revision 2.xx of the protocol: . . . . . . . . . . . . . . . . . . . . . . . 82
12.11 Reading Batch Quantity Value . . . . . . . . . . . . . . . 83
Revision 1.xx of the protocol: . . . . . . . . . . . . . . . . . . . . . . . 83
Revision 2.xx of the protocol: . . . . . . . . . . . . . . . . . . . . . . . 83
12.12 Setting a New Batch Quantity . . . . . . . . . . . . . . . . 84
>>>

Technical Handbook 019722-101 Rev. 05
vii
SC-350/SC-360
>>>
Revision 1.xx of the protocol: . . . . . . . . . . . . . . . . . . . . . . . 84
Revision 2.xx of the protocol: . . . . . . . . . . . . . . . . . . . . . . . 84
12.13 Resetting Counting Register to Zero. . . . . . . . . . . . 85
12.14 Resetting Memory Contents to Zero. . . . . . . . . . . . 85
12.15 Resetting Number of CountedCoins toZero . . . . . 85
12.16 Reading Machine Status . . . . . . . . . . . . . . . . . . . . 86
12.17 Disabling Keypad. . . . . . . . . . . . . . . . . . . . . . . . . 86
12.18 Disabling Keypad Except for Start/Stop . . . . . . . . . 87
12.19 Enabling Keypad . . . . . . . . . . . . . . . . . . . . . . . . . 87
12.20 Starting Machine . . . . . . . . . . . . . . . . . . . . . . . . . 87
12.21 Stopping Machine . . . . . . . . . . . . . . . . . . . . . . . . 88
12.22 Program Example . . . . . . . . . . . . . . . . . . . . . . . . 88
12.23 Electrical Connections . . . . . . . . . . . . . . . . . . . . . 92
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
12.24 ASCII Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
13 Interconnection Diagram . . . . . . . . . . . . . . . . . . . . . . . . 93
13.1 Electrical Block Diagram . . . . . . . . . . . . . . . . . . . . 93
13.2 CPU Board Circuit Diagram - Connector . . . . . . . . 94
13.3 CPU Board Circuit Diagram - CPU . . . . . . . . . . . . 95
13.4 CPU Board Circuit Diagram - Display/Keys. . . . . . . 96
13.5 CPU Board Layout . . . . . . . . . . . . . . . . . . . . . . . . 97
13.6 PSU Board Circuit Diagram . . . . . . . . . . . . . . . . . . 98
13.7 PSU Board Layout. . . . . . . . . . . . . . . . . . . . . . . . . 99
13.8 Serial Interface Board Circuit Diagram . . . . . . . . . 100
13.9 Serial Interface Board Layout . . . . . . . . . . . . . . . . 101
13.10 RD/AUX Interface Circuit Diagram. . . . . . . . . . . 102
13.11 RD/AUX Interface Board Layout. . . . . . . . . . . . . 103

General Information
Technical Handbook 019722-101 Rev. 05
1
SC-350/360
1 General Information
SUZOHAPP reserves the right to revise and improve its products as
it sees fit. This publication describes the product at the time of
publication and may not reflect the product at all times in the future.
This publication, or parts thereof, may not be reproduced in any
form, by any method, for any purpose other than the purchaser’s
personal use, without the express permission of SUZOHAPP.
1.1 Declaration of Conformity
We, SUZOHAPP, declare under our sole responsibility, that the
product in this manual, to which this declaration relates, is in
conformity with the following standards or other normative
documents:
EN 60 950-1:2006 + A11, EN 61000-6-1:2007 and EN 61000-6-3:2007
following the provisions of Directive:
• Low Voltage Directive 2006/95/EC;
•EMC Directive 2004/108/EC.
1.2 FCC Standard
FCC Part 15 (2008): Radio frequency device, subpart B:
Unintentional radiators. Class B equipment.
1.3 Environmental Compliance
Note! If the equipment contains batteries or accumulators, dispose these
separately according to local requirements.
WEEE Directive (valid in the EU only)
Waste Electrical and Electronic Equipment Directive 2002/96/EC.
Equipment marked with this symbol must be treated separately and
in accordance with the local legislation that requires proper treatment
of, recovery and recycling of used electrical and electronic
equipment.
Contact your SUZOHAPP representative for further details.

General Information
Technical Handbook 019722-101 Rev. 05
2
SC-350/360
1.4 Responsibility
The supplier of the equipment accepts no responsibility for injury or
damage to personnel or equipment, if the equipment is altered in any
way or used in a manner for which it was not intended at the time of
delivery.
If the conditions for use of the equipment are changed, the supplier
must be contacted or the declaration of conformity is invalidated.
1.5 About this Document
This technical handbook is valid for SC-350 and SC-360.
It provides information required by qualified personnel to carry out
repairs, maintenance and servicing.
Throughout this manual the instructions given apply to both
machines unless otherwise stated.
1.6 Revision History
1.7 Abbreviations/Acronyms
Revision Major Changes
05 Template updated.
Coin diameter and thickness ranges corrected.
04 Added new logos for SUZOHAPP and SCAN COIN on the
front page and changed from SCAN COIN AB to SUZOHAPP
on page 1.
03 Coin diameter range changed to 37.5 mm
5.3 “Functional” on page 13
Updated 3.7 “Accessories and Options” on page 10
02 Updated with new PSU board and Declaration of Conformity.
01 Added WEEE directive. Template updated.
Abbreviation Description
AC Alternating Current
AUX Auxiliary
BDO Bag Draw-Off
CPU Central Processing Unit
DC Direct Current
DMM Digital Multi Meter
ESD Electrostatic Discharge
LED Light Emitting Diode
PSU Power Supply Unit

General Information
Technical Handbook 019722-101 Rev. 05
3
SC-350/360
1.8 Related Documents
1.9 Software Version
This document describes machines with software versions:
•v.4.03 for SC-350
•v.4.03 for SC-360
Document Document number
(Main number)
User’s Guide 019223-xxx
Service Manual, including:
•Technical Handbook
• Spare Parts List
019721-101
•This document
• 019624-101

Safety Precautions
Technical Handbook 019722-101 Rev. 05
4
SC-350/360
2Safety Precautions
2.1 Hazard Notices
This handbook contains hazard information which must be
regarded by all users.
The hazard information is presented as a warning or a caution, as
follows:
WARNING!
Warnings indicate a potential hazard to the health and safety of
users. They clearly state the nature of the hazard and how to avoid it.
They appear at their points of application in this handbook, but with
different illustrations.
Caution! Cautions indicate a potential hazard to the physical integrity of the
machine, but not a danger to personnel. They clearly state the nature
of the hazard and how to avoid it. They appear at their points of
application in this handbook. They look like this notice, but with
different illustrations.
Note! The servicing information and instructions contained in this
technical handbook are for use by qualified personnel only.
Any unauthorised attempt, by unqualified persons, to service or
repair the machine, will nullify the equipment warranty.
2.2 Installation, Service and Maintenance
WARNING!
Risk of electric shock
High voltage inside the machine may be fatal
for anyone in contact with it. Always switch
OFF and disconnect the machine from mains
supply before disassembling.
Caution! Electrostatic discharge (ESD) may damage
the electronic components. All electronic
circuit boards in the machine are sensitive to ESD.
To prevent damage from ESD, always observe the following
precautions:
•Always wear a suitably grounded wrist wrap — make it first on,
last off.
•An unboxed or unbagged board is an unprotected board!
•Keep non-conducting materials (for example sleeves, ties, scarves)
away from electrostatic safe work areas.

Safety Precautions
Technical Handbook 019722-101 Rev. 05
5
SC-350/360
2.3 Operation
WARNING!
Risk of tipping!
The machine may fall over during bagging. Always make sure that the
bag can rest on a shelf. Maximum weight to avoid tipping is 10 kg (22
lbs).
WARNING!
Risk of jamming!
This machine contains moving parts and sharp edges. Always be
careful. Do not touch the components inside the machine while it is
running.
WARNING!
Risk of impaired hearing!
Use ear protectors while the machine is running.
2.4 Warning Labels
The following warning labels are attached to the machine.
SC-360

Introduction
Technical Handbook 019722-101 Rev. 05
6
SC-350/360
3Introduction
3.1 General
The SC-350/360 are universal, compact desktop machines for
counting coins and tokens.
The SC-350 has a manual coin tray and the SC-360 has an
automatic one.
3.2 Controls and Operation
Refer to the User’s guides for information.
SC-350
SC-360
1a
10
3
4
5
12
13
7
9
Rear of the machine
1 a Coin tray SC-360
b Coin tray SC-350
2Inspection lid
3 On/Off switch
4 Thickness selector
5 Reject cup
6RD/AUX connections
7 Serial interface connection
8 Power cord/Mains Inlet
9Fuse
10 Coin outlet
11 Diameter selector
12 Control panel
13 Coin diverter
Caution!
Do not use as a lifting handle.
2
11
1b
6
8

Introduction
Technical Handbook 019722-101 Rev. 05
7
SC-350/360
3.3 Main Components
>>>
1
SC-360
1 Hopper, SC-360 only
2 Hopper motor, SC-360 only
3Thickness unit
4 Coin disc
5 Feed unit
6Coin chute
7 Diameter unit
8 Control panel, CPU, PSU
2
3
4
5
6
7
8

Introduction
Technical Handbook 019722-101 Rev. 05
8
SC-350/360
>>>
3.4 Positional References
Unless stated the contrary, positions and directions such as left, right,
upper, lower, clockwise and counterclockwise are given with respect
to the machine when viewed from the front.
3.5 Modes of Operation
Refer to the User’s guides for information.
Machine turned upside down
9 Serial Interface & RD/AUX box
10 Pulley stand - Coin disc drive
11 Gear - Coin disc drive
Shaft and Bearing
12 Main motor
13 Pulley stand - Feeding
14 Belt stretcher
15 Support roller
16 Power supply box
9
10 11
12
13
14
15
16

Introduction
Technical Handbook 019722-101 Rev. 05
9
SC-350/360
3.6 Computer Communication
The SC-350/360 can communicate with many computer controlled
applications. A serial interface is fitted at the rear of the machine.The
machine can be used in many ways, for example:
•As a dispenser (SC-350/360):
The machine is used for dispensing coins. A cashier uses a
computer to control the machine so that it delivers the correct
amount of coins to each customer.
•In a cascade:
Several machines are connected in a cascade arrangement to form
a fast and efficient coin sorter. Each machine is connected to a
central computer and sorts only one coin denomination. The
computer carries out the accounting work by producing receipts
or by updating a database.
•As a massive coin counter:
Several machines are connected in a parallel arrangement to form
a coin sorter of considerably increased capacity. Each machine is
connected to a central computer which controls the operation of
the massive coin counter and carries out the accounting work by
either producing receipts or by updating a database.

Introduction
Technical Handbook 019722-101 Rev. 05
10
SC-350/360
3.7 Accessories and Options
All electrical accessories are plugged into sockets on the back of the
machine.
Accessories
Accessory Description
RD 8
012547-003
Remote customer display
Extra display showing the number of coins counted
(the same as normally shown on the display of the
machine).
BA 5
002726-004
Bagging attachment
Bag holder replacing the coin cup.
BG 1
010686-000
Bag guide without shelf
Mounted on the coin outlet. For small paper and
plastic bags.
BGS 1
002959-000
Bag guide with shelf
Same as BG 1 but with a shelf for the bag to rest on.
Note!
Only available until 2013-01-01
FC 3
015317-001
Foot control
For starting and stopping the machine.
SCAN COIN