Suzohapp Vision Pro 150TFT 2214 Series User manual

22" LCD Monitor
Model: 150TFT[X]2214[XX]
Manual
Version 1.4 / January 2015
Antonie van Leeuwenhoekstraat 9
3261 LT Oud Beijerland
The Netherlands
Phone :
[phone]
Fax :
[phone]
Email :
[email protected]
Web :
eu.suzohapp.com

Page 2 of 10
Index
1. Introduction..................................................................................................................................... 3
2. Safety ............................................................................................................................................... 3
3. Model descriptions .......................................................................................................................... 3
4. Monitor connection......................................................................................................................... 3
5. Monitor specifications..................................................................................................................... 4
6. Operation......................................................................................................................................... 5
7. OSD MENU....................................................................................................................................... 6
8. Driver software touch screen (optional 150TFT2214XX) ................................................................ 8
9. Mounting instructions ..................................................................................................................... 9
10. Accessories .................................................................................................................................... 10

Page 3 of 10
1. Introduction
Congratulations with the purchase of your monitor. This LCD monitor is a color active matrix thin-film-
transistor (TFT) liquid crystal (LCD) to provide superior display performance.
2. Safety
This monitor is only suitable for use in an indoor environment where there are not sealed, not subject
to dust, dirt, condensation (Pollution Degree 2) (IP20).
It is not allowed to connect appliances to the monitor which does not comply to SELV or Class II
qualification.
Turn off the monitor before cleaning.
The slots located on the backside of the monitor case are for ventilation. Do not block or insert
anything inside the ventilation slots.
It is important that your monitor remains dry. Do not pour liquid into or onto the monitor. If the monitor
becomes wet do not attempt to repair it yourself.
Unplug the monitor from the power outlet before cleaning. Do not use alcohol (methyl, ethyl or
isopropyl) or any strong dissolvent. Do not use thinner or benzene, abrasive cleaners or compressed
air. To clean the monitor, use a cloth lightly damped with a mild detergent.
If the liquid crystal materials leaks from the panel, it should be kept away from the eyes or mouth. In
case of contact with hands, legs or clothes, it must be washed away thoroughly with soap.
Warning: This is a class B product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
3. Model descriptions
Part number
Description
150TFT2214
Monitor 22”
150TFTG2214
Monitor 22” with 4mm tempered glass
150TFTS2214M
Monitor 22” with 3M touch screen serial
150TFTS2214MU
Monitor 22” with 3M touch screen USB
Further models to be announced.
4. Monitor connection
1. Connect the 12V power supply to the monitor.
2. Connect one end of the video cable to the computer and the other to the monitor. Tighten by
turning the two thumb screws clockwise to ensure proper grounding.
3. Connect one end of either the touch screen cable to the computer and the other end to the
monitor.
4. Press the power button on the rear panel to turn the monitor power on.

Page 4 of 10
5. Monitor specifications
Panel
Manufacturer
Part No.
Samsung
LM220MT12
Absolute Maximum Ratings
Item
Unit
Min
Typical
Max
Remarks
Operating Temperature
°c
0
-
50
Storage Temperature
°c
-20
-
60
Operation Humidity
%
20
-
90
Storage Humidity
%
35
-
75
Input characteristics
Description
Signal
Unit
Min
Typical
Max
Remarks
Power in (12Vdc)
Input
VDC
11.4
12
12,6
Consumption
A
0.5
0.8
1.2
Panel / Blue / Total
RGB Input
Analog RGB
VPP
0
0.7
-
Sync
VDC
0
5
5.5
H Frequency
KHz
31
64
80
Depends on Mode
V Frequency
Hz
55
75
76
Depends on Mode
DVI-D Input
DATA/CLK
VPP
450
500
900
Differential +/-
Display Characteristics
Item
Unit
Specifications
Screen Diagonal
[inch]
22
Active Area
[mm]
473.76 (H) x 296.1 (V)
Pixels
1680x3(RGB) x 1050
RoHS Compliance
RoHS Compliance
Optical Characteristics
Item
Unit
Conditions
Min.
Typ.
Max
Remarks
White Luminance
[cd/m2]
IRCFL=6.5mA(center
point)
240
300
-
1 (4mA)
Uniformity
%
9 Points
75
80
-
-
Contrast Ratio
1600
2000
-
Cross talk
%
-
-
1,5
-
Response Time
[msec]
Rising + Faling
-
20
-
-
Viewing Angle
[degree]
[degree]
Horizontal (Right)
CR = 10 (Left)
75
75
89
89
-
-
-
[degree]
[degree]
Vertical (Upper)
CR = 10 (Lower)
75
75
89
89
-
-
Color Gamut
%
-
72
-
Signal Input (Analog RGB, TMDS(DVI))
Item
Description
Resolution
Supported Resolutions
VGA
640x480
SVGA
800x600
XGA
1024X768
WXGA
1280X768
WXGA
1360X768
SXGA
1280X1024
WSXGA+
1680X1050

Page 5 of 10
6. Operation
Color LED: This LED shows the state of controller.
Green is the “normal state”.
Red is the “Off mode”. (Can’t find Sync. signals)
Blink is the “DPMS mode” (Display Power Management Signaling).
PC Settings: The PC needs to be set to an appropriate graphics mode that has the same resolution
with the LCD panel to have clear screen image. And the vertical refresh rate should be set to one of
56~75Hz, non-interlaced signal.
LCD display System Settings: The OSD (On Screen Display) provides certain functions to have
clear image and others. This board supports 5 buttons OSD operation as a standard. The control
functions defined on OSD operation are as below.
Pc Graphics Output: Signal quality is very important, if there is noise or instability in the PC graphics
output this may result in visible noise on the display. Refer to the graphic modes table in specification
section for supported modes. Non-interlaced & interlaced video input is acceptable.
USB cable (if installed): Plug the USB cable to the connector on the backside of the monitor.
Note: Use a USB cable with two ferrite bead’s at each end.
VGA cable: Plug the VGA cable to the connector on the backside of the monitor.
DVI-D Cable: Plug the DVI-D Cable to the connector on the backside of the monitor.
Power supply: Plug the 12V power supply (Not included) to the connector on the backside of the
monitor.
Power on: Switch on the monitor by using the on/off switch on the OSD control buttons.
PC Setting: The controller has been designed to take a very wide range of input signals however to
optimize the PC’s graphic performance we recommend choosing 60Hz vertical refresh rate this will not
cause screen flicker.
OSD Control Board: The OSD (On Screen Display) provides certain functions to have clear image
and others. This board supports 4 buttons OSD operation as a standard. The control functions defined
on OSD operation are as below.
The chosen OSD settings will be stored in memory. The OSD menu can be cleared from the screen
from the screen by moving the selection bar to the EXIT MENU icon pressing the SEL button
otherwise it will be automatically cleared after a few second of non-use.

Page 6 of 10
7. OSD MENU
The chosen OSD settings will be stored in memory. The OSD menu can be cleared from the
screen by pressing the MENU button otherwise it will be automatically cleared after a few seconds of
non‐use.
OSD Main Menu
[PICTURE] [COLOR]
[SCREEN] [OSD]
[SETUP]

Page 7 of 10
OSD GUI Control Table
MAIN
MENU
SUB MENU
CONTROL
Picture
Picture
Brightness
50(0~100)
Contrast
50(0~100)
Sharpness
2( 0 ~ 4)
Color
Color Status Management
User(User, Warm, Normal, Cool)
Red
50(0~100)
PC ONLY
Green
50(0~100)
Blue
50(0~100)
Auto Color
To Start
Screen
Auto Configure
To Start
H Position
50(0~100)
PC ONLY
V Position
50(0~100)
Clock
50(0~100)
Phase
30(0~100)
OSD
Language
English(English, Deutsch, Francais, Italiano,
Espanol, Korean)
H Position
50(0~100)
V Position
50(0~100)
Transparency
33 (0~100)
OSD Time
10(3~30)
SETUP
Source
RGB, DVI, AUTO
Factory reset
To Start
Aspect
Off(On/Off)

Page 8 of 10
8. Driver software touch screen (optional 150TFT2214XX)
3M Touch Systems provides driver software that allows your touch monitor to work with your
computer. Drivers are located on “3M Touch Systems” web site for the following operating
systems:
• Windows
• Linux
• Mac OSX
The latest versions of drivers and driver information for other operating systems are available
on the “3M Touch Systems” web site at:
http://solutions.3m.com/wps/portal/3M/en_US/TouchSystems/TouchScreen/
Your monitor is Plug-and-Play compliant. Information on the video capabilities of your
monitor is sent to your video display adapter when Windows starts. If Windows detects your
monitor, follow the instructions on the screen to install a generic Plug-and-Play monitor.
Depending upon whether you connected the USB communication cable, you should
install only the USB driver.

Page 9 of 10
9. Mounting instructions
Monitor Mounting
This monitor can be mounted with twenty M4 mount holes. Follow the steps described below:
Place the monitor into the machine.
Place the M4 screws on the both sides of the monitor. Tighten the nuts until the monitor is firmly
secured to the machine.
*Dimensions without glass
With glass standard +4,0mm
*
*
*
*

Page 10 of 10
10.Accessories
Part number
Description
150-0049
Power supply input 100/240V output
12V 5A
22-0012-4
Power cable Euro lead 1.80M
149-0112-11
VGA cable 1.80m
149-0121
DVI-D Cable 2 mtr. 18+1
149-0111-2
Serial cable 2m
98-0003-2209-3
22 “ Touch screen (without controller)